Dynasty Fireplaces DY-BTW40 Quick start guide

Homeowner’s
Installation Instructions &
Operating Manual
Model: DY-BTW40 - DY-BTW84
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN
THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE
TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR
PROPERTY DAMAGE.
Dynasty Fireplaces
#10-3071 No.5 Road, Richmond, BC V6X 2T4 Canada
WARNING! To reduce the risk of fire, electric shock, or personal
injury, read all the instructions before using this heater.

1

2
CONTENTS
CSA / Power Cord Labels
…………………………………………………………………………………..
2
Important Safety Information & Warnings……..
…………………………………………………………….
3
Preparation
……………………………………………………………………………………………..............
5
Packing List
.…………………………………………………………………………………………….
5
Product Dimension
……………………………………………………………………………………………..
6
Assembly
………………………………………………………………………………………………………
7
Battery Information
…………………………………………………………………………………………
11
Operation
………………………………………………………………………………………………………..
11
Control Panel
…………………………………………………………………………………………..
12
Remote Control
……………………………………………………………………………………….
13
Care and Maintenance
………………………………………………………………………………………
14
CSA / POWER CORD SAFETY LABELS
CSA Rating Label
Power Cord Warning Label
IMPORTANT SAFETY INFORMATION!

3
WARNING
Read all instructions before using this heater!
This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If
provided, use handles when moving this heater. Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front
of the heater, and keep them away from the sides and rear.
Extreme caution is necessary when any heater is used by or near children or invalids and
whenever the heater is left operating and unattended.
DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions,
has been dropped or damaged in any manner. Discard heater, or return to authorized
service facility for examination and/or repair.
DO NOT run power cord under carpeting. DO NOT cover power cord with throw rugs,
runners, or similar coverings. DO NOT route power cord under furniture or appliances.
Arrange power cord away from traffic area, and where it will not be tripped over.
DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening, as
this may cause electric shock or fire, or damage the heater.
To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. Doing so
could cause a fire. DO NOT use on soft surfaces, like a bed, where openings may become
blocked.
A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where
gasoline, paint, or flammable liquids are used or stored.
Use this heater only as described in this manual. Any other use not recommended by
the manufacturer may cause fire, electric shock, or injury to persons.
ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an
extension cord or relocatable power tap (outlet/power strip).
DO NOT place the heater near a bed because objects such as pillows or blankets can fall
off the bed and be ignited by the heater.
NEVER use this heater in bathrooms, laundry rooms, or any other location where the
heater could fall into a bathtub or pool, become damp, or come in contact with water.
AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other
blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.
NEVER hang this unit on a wall directly below an electrical outlet.
NEVER permanently install in a recessed area of the wall. This may result in blocked air
flow, overheating, or fire.
ALWAYS mount to wall bracket before use.
NEVER use a wall mount bracket from another manufacturer.
WARNING

4
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK---DO NOT USE THIS
HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.
For residential use only! NOT for commercial use! Any commercial or public use of this
heater voids all warranties, and could cause injury.
This product is not intended to be a primary heat source. It is for supplemental heat
only.
INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric
shock!
Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
NEVER modify this heater. Doing so could result in personal injury or property
damage. Modification of this fireplace completely voids all warranties.
ALWAYS turn this heater off before unplugging it from the outlet.
ALWAYS disconnect this unit from the power supply before performing any assembly or
cleaning, or before relocating the electric fireplace.
NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.
ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet.
ONLY use this heater on a 120V AC 15-Amp circuit. NEVER overload the circuit. If this
heater trips the circuit breaker, unplug all other appliances on the same circuit before the
next use. Avoid plugging other appliances into the same circuit as this heater.
NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or
connections. Plugging this heater into a faulty outlet could result in electric arcing
within the outlet that could cause the outlet to overheat or catch fire.
ALWAYS check your heater cord and plug connections with each use!
a. MAKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or loose plugs
can cause the outlet to overheat.
b. Heaters draw more current than small appliances. Overheating may occur even if it has
not occurred with the use of other appliances.
c. During use check frequently to see if the plug outlet or faceplate is HOT! If the outlet or
faceplate is HOT, discontinue use immediately and have a qualified electrician inspect
and/or replace the faulty outlets.
This heater has a polarized plug (one blade is wider than the
other). As a safety feature to reduce the risk of electrical shock,
this plug is intended to fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not attempt to
defeat this safety feature.
SAVE THESE INSTRUCTIONS!

5
PREPARATION
This carton includes GLASS! ALWAYS use extreme caution when handling glass.
Failure to do so could result in personal injury or property damage.
Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts
and assembly steps are grouped for free-standing or wall-hanging use. Check the parts list to make
sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever
possible.
PACKING LIST
A - Fireplace (1)
B-Glass Panel (1)
C-Remote Control (1)
D-AAA Battery (2)
E-Larger Crystal Stones (1 set)
F-Small Crystal Stones (1 set)
G- ST 3*8 Metal Screws (2)
H- ST 4*10 Metal Screws (4)
I- ST 4*25 Wood Screws (4)
J- Fixing Brackets (2)
K- Washers (4)
L- Owner’s Manual (1)

6
PRODUCT DIMENSION
Model
A
B
C
D
E
F
G
EF172B(DY-BT40)
40 9/16″
(1030mm)
20 1/4″
(515mm)
31 1/2″
(800mm)
11 1/4″
(285mm)
35″
(888mm)
17 13/16″
(453mm)
5 11/16″
(145mm)
EF173B(DY-BTW48)
48 7/16″
(1230mm)
20 1/4″
(515mm)
39 3/8″
(1000mm)
11 1/4″
(285mm)
42 13/16″
(1088mm)
17 13/16″
(453mm)
5 11/16″
(145mm)
EF174B(DY-BTW60)
60 1/4″
(1530mm)
20 1/4″
(515mm)
51 3/16″
(1300mm)
11 1/4″
(285mm)
54 5/8″
(1388mm)
17 13/16″
(453mm)
5 11/16″
(145mm)
EF175B(DY-BTW68)
68 1/8″
(1730mm)
20 1/4″
(515mm)
59 1/16″
(1500mm)
11 1/4″
(285mm)
62 1/2″
(1588mm)
17 13/16″
(453mm)
5 11/16″
(145mm)
EF176B(DY-BTW84)
83 7/8″
(2130mm)
20 1/4″
(515mm)
74 13/16″
(1900mm)
11 1/4″
(285mm)
78 1/4″
(1988mm)
17 13/16″
(453mm)
5 11/16″
(145mm)

7
ASSEMBLY
STEP 1. Find a safe location. Minimum clearance from the ceiling and the mantel must be at
least 8 inches (200mm); minimum clearance from the front must be at least 3 feet (900 mm).
Choose a location near an outlet so an extension cord is not required. DO NOT position the unit
directly below a power outlet. See Safety Information on pages 3 and 4 for more warnings
about placement, installation, and use of this product.
MODEL
DY-BT48
EF173B
DY-BT60
EF175B
EF176B
A
36 7/16″
(925mm)
44 5/16″
(1125mm)
56 1/8″
(1425mm)
64″
(1625mm)
79 3/4″
(2025mm)
STEP 2. Take model EF173B as an example. Prepare a wall with a framed opening of 44 5/16”
(1125mm) wide ×18 1/8” (460mm) high. Make sure the width of the wood block on both sides
which used to fix the fireplace is 3”. (76mm) Make sure that the revealed wood block width on
both sides is about 1 1/2”(37.5mm) after finishing the plasterboard. Measure the depth D from the
plasterboard surface to the wood block and write it down.

8
STEP 3. Take out the two fixing brackets and 4pcs ST4X10 screws with 4 washers to fix on the left
and right side panel of the unit. Make sure the distance from the fixing brackets to the fireplace
surface is equal to D in order to make sure the firebox surface is not lower than the plasterboard
surface.
A.
B.
STEP 4. There are two kinds of electrical connections. A. Existing appliance installation. Drag the
power cord through the hole and plug it into the outlet and push the unit into the recessed wall in
parallel. If an existing grounded outlet is near the appliance, the power cord can run behind the
appliance. If the cord is not long enough to reach the outlet, a grounded extension cord minimum
AWG No. 14 wiring and rated to a minimum or 1875 watts may be used. B. Hard-wire installation.
If it is necessary to hard wire this appliance, a qualified electrician may remove the cord
connection, and wire the appliance directly to the house hold wiring. The appliance must be
electrically connected and grounded in accordance with local codes. 1. Remove the cord
connection. 2. Wire to a properly grounded, 120volt, 60Hz, 15 AMP circuit. 3. Ensure all junction
block connections are tight. 4. Replace the cover and retaining screws.
NOTE! To reduce the risk of fire, do not run the power cord under rugs, carpets, etc.
Arrange the power supply cord away from high traffic areas where it may be pose a
tripping hazard.

9
STEP 5.Fix the 4pcs ST4X25 screws on the wood block. Make sure the front of the firebox is not
lower than the surface of the wall.
STEP 6. Carefully spread the small crystal stones across the fuel bed. Then evenly arrange the
larger crystal stones along the inset window ledge at the front of the firebox.
The next step requires installation of a GLASS panel! The manufacturer recommends
that two adults install the glass panel. Always use extreme caution when handling
glass. Failure to do so could result in personal injury or property damage.
STEP 6. Carefully set both hooks of the front glass panel onto the firebox. NOTE: Make sure
the glass fully attached to the firebox so that the control panel can work properly. This will
keep the decorative glass in place and enable the control panel work.

10
STEP 7. Thread the ST3x8 screws (2)into the threaded holes on the glass panel. Check the
alignment of the glass panel and securely tighten the screws.

11
BATTERY INFORMATION
Remote Control Battery
This remote control uses two AAA batteries (included).
Instructions for battery installation are inside the Remote Control battery compartment.
Always replace the battery in the remote control with the same type of battery.
NEVER dispose of batteries in fire. Failure to observe this precaution may result in an
explosion.Dispose of batteries at your local hazardous material processing center, or
as required by local ordinances.
OPERATION
Read and understand this entire owner’s manual, including all safety information,
before plugging in or using this product. Failure to do so could result in electric
shock, fire, serious injury, or death.
Power
Make sure the ON/OFF switch, located on the control panel, is in the OFF position. Plug the power
cord into a 110~120 Volt 15 Amp outlet (see IMPORTANT SAFETY INFORMATION on Pages 3
and 4). Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the
maximum amperage for the circuit. DO NOT plug other appliances into the same circuit.
Temperature Limiting Control
This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe
temperature (212F / 100C), the heater will automatically turn OFF. To reset:
1. Unplug the power cord from the outlet.
2. Turn the ON/OFF switch on the CONTROL PANEL to OFF. Wait at least 5 minutes.
3. Inspect the fireplace to make sure no vents are blocked, or clogged with dust or lint. If they
are, use a vacuum to clean the vent areas.
4. With the POWER switch in the OFF position, plug the power cord back into the outlet.
5. If it switches off again, UNPLUG THE HEATER RIGHT AWAY! Have the outlets, wiring,
and breaker box inspected by a professional. Make necessary repairs before using the
heater.
Heater Rating
Maximum Heat Output: 1500 W (5120 BTU); Maximum Heating Area: 400 square feet.
Methods of Operation
CONTROL PANEL: Located on the front glass panel of the fireplace (see figure below).
Controls ON/OFF, FLAME EFFECT, HEATER and FUEL BED.
REMOTE CONTROL (Battery included):
Controls ON/OFF, FLAME EFFECT, HEATER, THERMOSTAT, TIMER and FUEL BED.
Review the IMPORTANT SAFETY INFORMATION on Pages 3 and 4 before operating.

12
CONTROL PANEL
BUTTON
FUNCTION
ACTION & INDICATION
ON/OFF
ON: Turns on.
OFF: Turns off.
1. Press to turn the power on.
2. Press to turn the power off.
FLAME
Controls the flame effect brightness.
Cycles through 4 levels of flame
brightness.
1. Press once to turn the flame effect on.
2-4. Press again to cycle through 4 levels
of flame brightness.
HEATER
Controls the 3 levels heat.
The heater will be cycled Low –High –
Heater Off. You will see the indicator light
illuminates. The indicator light goes out
within 10s.
Low: (●○)
High: (●●)
FUEL BED
Controls the LED light strips at the bottom
of the fuel bed. The LED lights include
alternating color combinations.
1. Press once to turn the fuel bed light on.
2-14. Press again to cycle through 14
color options of the fuel bed.
NOTICE
When the heater is first turned on, a slight odor may be present. This is
normal and should not occur again unless the heater is not used for a
long period of time.
NOTICE
Do not move or remove the glass panel when the appliance is plugged in
and operating. This will cause the control panel to no longer function.

13
Remote Control
NOTICE
Aim the remote control at the remote receiver. Make sure you hear a beep
each time you press the button! If not, the fireplace will not respond to the
signal.
BUTTON
FUNCTION
ACTION & INDICATION
ON/OFF
ON: Turns on.
Note:
All the functions are off in the standby mode, it
will memorize the working condition of flame
effect and heating.
OFF: Returns the unit to standby mode.
1. Press. The flame effect and the
remote control functions are enabled.
The flame setting will display on the
remote control screen.
2. Press. The flame effect and all the
functions will turn off. The remote
control screen will go blank.
FLAME
Controls the flame effect brightness.
Cycles through 4 levels of flame brightness .
1. Press once to turn the flame effect
on.
2-4. Press again to cycle through 4
levels of flame brightness .
HEATER
Press once turns Fan on, and 10s later Low
heat on. (Pilot lights illuminated ●○)
Press again turns on High heat. (Pilot lights
illuminated ●●)
Press third time turns heat off. 10s later fan off
(Pilot lights illuminated ○○)
1. Press. The heater turns on low
heat.
2. Press. The heater turns on high
heat.
3. Press. Turn off the heat.
TEMP
Controls the thermostat setting.
Thermostat: Automatically turns the heater
on and off to maintain the temperature.
If the thermostat is set below the room
temperature, the heater will turn off.
NOTE: The thermostat only works when the
heater is on.
1) NOTE: The heat will not change as the room
temperature change when there is no
temperature shows on the remote screen.
NOTE: It will change between C and F after
pressing the button for 3s. 60-84F
corresponds to 16-28C. It can not be
operated in the standby mode, but the
temperature still displays on the remote
control screen.
1. Turn the heat on. Press.
The temperature displays 24C.
2-13. Press again to increase the
temperature by 1C interval up from
16C to 28C (maximum setting).
14. Press again. The thermostat
turns off. No temperature is
displayed.
15. Press. Start at 23C.
TIMER
Controls the timer settings.
The timer turns off the fireplace at the set time,
from 0.5 hours to 9.0 hours.
1-10. Press .
Timer setting: 0.5H, 1.0H,
and then each hour up to 9.0H.
11. Press. Off. No time is displayed.
FUEL BED
Controls the LED light strips at the bottom of
the fuel bed.
1. Press once to turn the fuel bed
light on.
2-14. Press again to cycle through
14 color options of the fuel bed.

14
CARE AND MAINTENANCE
ALWAYS turn the heater OFF and unplug the power cord from the outlet before
cleaning, performing maintenance, or moving this fireplace. Failure to do so could
result in electric shock, fire, or personal injury.
Cleaning
NEVER immerse in water or spray with water. Doing so could result in electric
shock, fire, or personal injury.
Metal:
Buff using a soft cloth, slightly dampened with a citrus oil-based product.
DO NOT use brass polish or household cleaners as these products will damage the metal
trim.
Glass:
Use a good quality glass cleaner and dry thoroughly with a paper towel or lint-free cloth.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
Plastic:
Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
Vents:
Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
Clean the exterior of the fireplace with a slightly damp cloth or duster.
Maintenance
Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
ALWAYS turn the heater OFF and unplug the power cord from the outlet before
cleaning, performing maintenance, or moving this fireplace. Failure to do so could
result in electric shock, fire, or personal injury.
Electrical and Moving Parts:
The fan motors are lubricated at the factory and will not require lubrication.
Electrical components are integrated in the fireplace and are not serviceable by the
consumer.
Storage:
Store heater in a clean dry place when not in use.
Replacement parts:
Use only replacement parts supplied by the manufacturer. Use of any other parts, or
modifying the fireplace in any way, will void all warranties.
No internal parts are replaceable or serviceable.

15
In the unlikely event of a problem occurring due to a manufacturing fault within 24 months from the
date of purchase of the appliance it will be repaired or replaced free of charge.
This warranty does not cover consumable items such as the bulbs and fuses which have a limited
lifespan.
If a problem should occur, the nature of the problem together with the date of a purchase should be
immediately reported to the retailer that the appliance was purchased from. Proof of purchase will
be required so the original invoice should be retained.
Dynasty Fireplaces
#10-3071 No. 5 Road, Richmond, BC V6X 2T4 Canada
Telephone: [phone] Toll free: 1-877-521-1009
WARRANTY