E-matic PMSCF User manual

PMSCF Instructions Rev02
MODEL: PMSCF
INSTALLATION AND OPERATING INSTRUCTIONS FOR CEILING PIR SENSOR
Thank you for choosing PMSCF PIR s nsor. This s nsor is suitabl for INDOOR us only. Pl as r ad th s instruction b for
installation and k p for futur r f r nc .
IMPORTANT: Installation must be performed by a skilled/competent person w o is familiar wit t e appropriate standards and
tec nical requirements of t e appliance and its proper installation.
Never modify t e unit, t ere are no user serviceable parts inside. Not suitable for use wit dimmer switc es. Install in accordance
wit IEC Wiring Regulations.
■ POSITIONING THE UNIT
W en selecting t e mounting position, please take t e following points into account:
1. T e sensor is designed for optimum performance to be mounted on t e ceiling (see Figure 2)
2. Ensure t at t e sensor cannot pick up or is close to eat sources suc as eater or eat extraction units, w ic may cause
false triggering.
3. If you set t e Lux control level to nig t (), ensure t at t e sensor cannot detect brig t lig t as t at t e unit will not work.
4. Do not fit t e sensor near strong electromagnetic fields as false activations may occur.
■ FITTING THE UNIT (S Figur 1)
B for any l ctrical work, nsur mains supply cabl s is isolat d by switching off and r moving th r l vant fus .
1.Drill a circle ole of around 2.5-inc (63.5mm) diameter in t e ceiling w ere you are to mount t e sensor
2.Remove t e terminal cover ① and unscrew t e cable clamp ② (see Figure 1)
3.Connect t e main supply cable to t e corresponding terminals
Figure 1
Black(Load)
Blue(Load)
1
2
Blue (Main
power Neutral)
Brown (Main
power Activel)
LN L
out in
in
out
L
N
L
Ceiling
360°
RadiusMax 4.5M Max 4.5M
360°
Ceiling
RadiusMax 4M Max 4M
Detection Area Figure 2

PMSCF Instructions Rev02
4.Secure t e cable by re-screwing t e cable clamp. Fix t e terminal cover back
5.Press t e side springs up, old t em and mount t e sensor into t e ceiling ole (see Figure 3)
Aft r finishing th fitting op ration, you can adjust th d t ction ar a and working stat of PIR s nsor
■ OPERATION MODE:
WALK TESTING:
W en t e mains supply is switc ed on to t e PMSCF, t e PMSCF sensor will enter into a “WARM-UP” period for approximately 1
minute and t en automatically c ange to “AUTO MODE”. W ile sensor is in t e AUTO MODE, you can t en carry out a Walk-Test
by placing t e LUX control to day position () and t e TIME control to minimum (-). Once t e PMSCF sensor receives a valid
trigger signal (suc as movement of a person) wit in its detection area, t e lamp(s) (load) will be turned on for t e pre-set period
of time. You will be able to determine t e detection area by walking slowly.
Pl as Not : Movement across t e detection area is more effective t an movement directly toward or away from t e sensor.
(Refer Fig.4A). If movement is towards or away from t e sensor, not across, t e detection range will be reduced. (Refer Fig. 4B)
Aft r compl ting th walk-t st, s t th LUX DIAL to th r quir d night position to nsur PMSCF only op rat s at night or
r quir d light l v l and s t TIME DIAL to th d sir d “ON’ tim .
ADJUSTING THE LUX CONTROL LEVEL:
T e Lux control module as a built-in p otocell t at detects daylig t and darkness.
() position denotes t at t e lamp(s) (load) will be turned on by PIR during day and nig t.
( ) position denotes t at t e lamp(s) (load) will be turned on by PIR only at nig t.
You can set to operate t e unit at t e desired level by adjusting t e LUX knob
ADJUSTING THE DURATION TIME:
T e duration time is “t e lengt of time t at t e PMSCF switc es t e load ‘on’ after activation”. T e duration time can be adjusted
from (10±5) seconds to (30±3) minutes. Rotating t e TIME knob from (+) to (-) will reduce t e duration time.
Not : Once t e lamp(s) (load) as been triggered by t e PIR sensor any subsequent detection will start t e timed period again
from t e beginning.
■ ATTENTION:
1. B for any l ctrical work, nsur mains supply cabl is isolat d by switching off and r moving th r lativ fus .
2. Th r ar not any s rvicing parts insid , do not att mpt to modify or s rvic th unit.
3. It is normal that th load will d lay s v ral s conds to b turn d on wh n pow r on.
Fig. 4(B) Not
Good
Fig. 4(A)
Good
Figure3

PMSCF Instructions Rev02
■ IMPORTANT:
N v r att mpt to r mov th l ns cov r as this will damag th s nsor and r nd r all guarant s invalid.
■ TECHNICAL DETAILS:
Voltag ：
：：
： 220 -240VAC 50 Hz
Wattag ：
：：
： Max. 2000W incandescent bulb (resister-load) or 600W fluorescent load, LED 60W-200W (depends on
different quantity LED driver)
D t ction rang : 360°, radius 4.5 meters wit installation eig t of 2.8 meters
Duration tim ：
：：
： From (10±5) seconds to (30±3) minutes adjustable
Lux control l v l: From daylig t to nig t
Due to our policy of continuous improvement we reserve t e rig t to c ange specification wit out prior notice.
Errors and omissions excepted. T ese instructions ave been carefully c ecked prior to publication. However, no responsibility can
be accepted by E-Matic for any misinterpretation of t ese instructions.
E-Matic Energy Management Solutions
10 Sandersons Way, Marton,
Blackpool, FY4 4NB
Tel: [phone], Fax: [phone]
Email: [e-mail]
Web: www.e-matic.co.uk