Early Childhood Resources ELR-0634 User manual

G
G
G
G
D
Q
J
F
F
F
F
F
F
FF
4
A1
2
D
G
G
G
G
F
F
F
F
D
C
E
GGGG
EX8
K
X8
Q
2A. Two Adults Suggested: On a carpet, or protected surface, attach
Upper Dividers(F) to the Lower Center Shelf(D) using 8 Flat Hex-Head
Screws(L), using 2 in each. Tighten with the Hex Key Tool(M).
2B. Insert 8 Metal Dowels(J) into the plastic plugs located underneath
Lower Center Shelf(D). Tighten with a Phillips Head Screwdriver.
B
Left Side Panel
Right Side Panel
Top Shelf
Upper Center Shelf
Lower Center Shelf
Bottom Shelf
Upper Divider(4)
Lower Divider(4)
Lower Back
Upper Back(5)
Metal Dowels(16)
RoundHexHead
Screw(24)
FlatHexHead
Screw(8)
Hex Key Tool
Hooks(10)
Posts(12)
Post Screws(12)
Cams(16)
D
E
F
A1
A2
C
H
I
J
K
L
G
M
N
O
P
Q
NOTE:
A Phillips Head Screwdriver
will be needed for
assembly (not included)
E
FFFF
G
G
GG
A2
B
A2
IIIII
H
B
C
5-Section Coat Locker
with Bench
Model # ELR-0634
Mount Laurel,NJ 08054 USA
www.ecr4kids.com
1
!
WARNING:
-AdultAssembly Required.Two
adultsrecommended.
-Containssmall parts,sharppoints
andedges.
-Donot stand,sit,kneel, climb,lean
orpullon unitforsupport.
-Neverleave childrenunattended.
-Donot placeunitnear highheator
moisture.
-AdultSupervisionRecommended.
TIP！
DO NOT FULLY
TIGHTEN SCREWS
UNTIL ALL SCREWS
HAVE BEEN LOOSELY
POSITIONED。
BEFORE ASSEMBLING,
MAKE SURE THERE
ARE NO
MISSING PARTS.
Attach Lower Dividers to
Bottom Panel
1A.Attach 4 Lower Dividers(G) to the Base(E) using 8 Round Hex Head
Screws(K), using 2 in each. Tighten with the Hex Key Tool(L).
Attach the Upper Dividers to the
Lower Center Shelf
L
X8 X8
J
3Attach the Top Section to the
Bottom Section
3C. Turn Cams(Q)
with a Phillips Head
Screwdriver until
locked onto the Metal
Dowels(J).
4A. Insert Upper Center
Shelf(C) onto the slots in
the 4 Upper Dividers(F) as
shown, until fully engaged.
I
III
H
D
E
I
C
Version: ELR-0634.D.2010.01.02
4B. Two Adults
Suggested: Carefully
stand the unit upright.
4C. Slide the 5 Upper
Backs(I) into the grooves
between the Upper
Dividers(F) and into the
groove in the Lower Middle
Shelf(D) until fully inserted.
4D. Slide the Lower
Back(H) into the grooves
between Lower Middle
Shelf(D) and Bottom
Shelf(E) until fully inserted.
F
F
F
F
Attach the Upper Center Shelf
and Back Panels
3A. Lay the assembled Base(E,G) on its side. Insert 8 Cams(Q) into the
large holes located in the 4 Lower Dividers(G), using 2 in each. Make
sure the arrows on Cams(Q) point toward the holes in the closest ends.
3B. Two Adults Suggested: Position the assembled Upper Section(D,F)
so the Metal Dowels(J) attached to Lower Center Shelf(D) enter the holes
in the top edges of the Lower Dividers(G) as shown.
- If the Back Panel does
not slide easily into the
grooves, wiggle the Back
while pushing the panel
into the slot.
- You may also turn the
rear Cams on the shelf
above or below to unlock,
push the Back until fully
inserted into the slot, then
turn Cams to the locked
position again.
TIP:

5
6
7
8
We appreciate your purchase of the 5-Section Coat Locker
with Bench. Early Childhood Resources has made every
effort to supply a quality product, that with proper use and care,
will bring you many years of trouble free use!
Clean wood with a damp cloth or sponge using warm water and
mild soap. Wipe dry.
Do not place near heat, moisture or vaporizer which may cause
wood to warp and peel.
Check for loose or worn parts periodically and tighten or
replace as necessary.
Care and Cleaning
“Early Childhood Resources® guarantees the quality
of all of our products. You can trust the quality and
safety of our furniture and materials, along with the
peace of mind that our products are made to last. If
for any reason, you are not satisfied with the quality
and workmanship of our products, we will replace the
item or refund the sale.”
JQ
C
E
D
IF
F
F
BJ
Q
F
Attach the Top Shelf
5A. Insert 8 Metal
Dowels(J) into the plastic
plugs located underneath
Top Shelf(B). Tighten with
a Phillips Screwdriver.
5B. Insert 2 Cams(Q) into
the large holes in each of
the 4 Upper Dividers(F).
Make sure the arrow on the
Cams(Q) point toward the
holes in the closest edge.
5C. Position Top Shelf(B)
so the attached Metal
Dowels(J) enter the holes
in top edges of the Upper
Dividers (F). Turn Cams(Q)
with Phillips Screwdriver
until locked onto the Metal
Dowels(J).
Attach the Side Panels
K
Ｘ８
C
E
D
I
F
F
F
B
F
A1
6A.Attach the Left Side Panel(A1) to the assembled unit as shown,
using 8 Round Hex Head Screws(K). Tighten using the Hex Key
Tool(M).
C
E
I
F
F
F
B
F
A2
A1
D
K
Ｘ８
K
K
6B.Attach the Right Side Panel(A2) to the
assembled unit as shown, using 8 Round
Hex Head Screws(K). Tighten using the
Hex Key Tool(M).
!
CAUTION:
- Do not allow children to climb or stand on shelves.
- Do not use as a stepladder.
Attach the Coat Hooks
7A.Attach 8 Hooks(N) to the 4 Upper Dividers(K) using 8 Posts(O)
and 8 Post Screws(P). Tighten with a Phillips Head Screwdriver.
7B.Attach 8 Hooks(N) to the Side Panels (A1,A2) using 4 Posts(O)
and 4 Post Screws(P). Tighten with a Phillips Head Screwdriver.
You are done!
A1
FFFF
A2
N
Ｘ１０ O
Ｘ１２ P
Ｘ１２
Version: ELR-0634.D.2010.01.02
Purchase Order Number:
Record the Purchase Order Number here. Information is
located on a label enclosed, and on the shipping carton.
Place label and this sheet in an accessible place.
Model Number: ELR-0634