Early Childhood Resources ELR-0728 User manual

C
D
E
F
G
H
I
J
K
L
M
Top Panel (1)
Left & Right
Side Panels (1/1)
Parts List
A
B
BEFORE ASSEMBLING, MAKE SURE YOU HAVE ALL THE PARTS
Front
Crossbar (1)
Lower Back
Panel (1)
Rear
Dividers (2)
Front
Divider (1)
Shelves (3)
Decorative Hex Screws (22)
Flat Head Hex Screws (4)
Cam Posts & Cam Locks (6/6)
M1 M2
Bottom Shelf (1)
Lower Dividers (2)
Upper Back Panel (1)
Batch ID Sticker
located on underside
Use the
Hex Tool.
Use the
Hex Tool.
Use a Phillips
Screwdriver.
A1 A2
Book Display with Storage
- 3 Compartment -
Model# ELR-0728
Adult Assembly Required.
Two adults recommended.
- Contains small parts, sharp points and edges.
- Do not stand, sit, kneel, climb, lean or pull on
unit for support.
- Never leave children unattended.
- Do not place unit near high heat or moisture.
- Adult supervision recommended.
WARNING:
TOOLS INCLUDED
Hex Tool (1)
TOOLS NEEDED
Phillips Screwdriver
Mt. Laurel, NJ 08054 USA
www.ecr4kids.com

1Install Lower Dividers
2Install Front Crossbar & Front Divider
3Connect Top Panel to Lower Dividers
4Insert the Lower Back Panel
Connect the Upper Back Panel
5
Install the Lower Dividers (D) onto the Bottom Shelf (C) with four Decorative Hex Screws (K)
using the Hex Tool.
Note: The groove on
the Bottom Shelf is
toward the ground.
Install the Front Crossbar (G) and Front Divider (I) onto the Top Panel (B) with four Flat Head
Hex Screws (L) using the Hex Tool.
Place two Cam Locks (M2) into the recessed holes on each Lower Divider (D) with the arrow
facing the closest edge.
Place two Cam Locks (M2) into the recessed holes on the Upper Back Panel (E) with the
arrow facing the closest edge.
Install four Cam Posts (M1)
into the threaded plastic
inserts on the underside of
Top Panel (B) with a Phillips
screwdriver.
Reminder: Do not
overtighten, as the plastic
threads can be stripped.
Insert the Top Panel (B)
Cam Posts into the holes on
the top edge of the Lower
Dividers (D). Turn the Cam
Locks clockwise with a
Phillips screwdriver to lock
the Lower Dividers (D)
onto the posts.
Insert the Upper Back Panel (E)
onto the Cam Posts (M1) on the
topside of Top Panel (B). Turn
the Cam Locks clockwise with a
Phillips screwdriver to lock the
Upper Back Panel (E) onto the
posts.
Batch ID Sticker
See Next Page
Slide the Lower Back Panel (F) into the grooves on the underside of Top Panel (B) and topside
of the Bottom Shelf (C) as shown, center the panel so it will seat into the grooves on the inside
of the Side Panels.
Tip: If the Back Panel does not slide in easily, wiggle the panel while pushing into place.
Install two Cam Posts (M1) into the threaded plastic inserts on the topside of Top Panel (B) with
a Phillips screwdriver.
Reminder: Do not overtighten, as the plastic threads can be stripped.

6Install the Left Side Panel
Install the Rear Dividers
7
8Install the Shelves
Install the Right Side Panel
9
Install the Left Side Panel (A1) onto the Top Panel (B), Bottom Shelf (C), Upper Back Panel (E)
and Front Divider (I) with seven Decorative Hex Screws (K) using the Hex Tool.
Reminder: Make sure the pre-installed wood dowels on the ends of the Front Divider and
Crossbar enter the corresponding holes on the inside of the Side Panels before final tightening.
Install the Right Side Panel (A2) onto the Top Panel (B), Bottom Shelf (C), Upper Back Panel (E)
and Front/Rear Dividers (G/H) with nine Decorative Hex Screws (K) using the Hex Tool.
Reminder: Make sure the pre-installed wood dowels on the ends of the Front/Rear Dividers and
Crossbar enter the corresponding holes on the inside of the Side Panel before final tightening.
Slide the Shelves (J) into the grooves on the sides of Upper Back Panel (E) and Front/Rear
Dividers (G/H) as shown, until seated against the inside of Left Side Panel (A1).
Tip: If the Shelves do not slide in easily, wiggle them while pushing into place.
Install the Rear Dividers (H) onto the Left Side Panel (A1) with two Decorative Hex Screws (K)
using the Hex Tool, with the pre-installed wood dowels on the ends entering their corresponding
holes.
Reminder: Make sure the grooves on the Rear Dividers (H) align with those on the Upper Back
Panel (E) and Front Divider (I).
See Next Page
Reminder: Push the Lower Back Panel (F)
so it is fully seated into the groove on the
inside of the Left Side Panel (A1)

©2011 ECR LLC Version: ELR-0728.2011.04.04
We appreciate your purchase of the Book Display with Storage - 3 Compartment.
Early Childhood Resources has made every effort to supply a quality product,
that with proper use and care, will bring you many years of trouble free use!
“Early Childhood Resources® guarantees the quality of all of our products. You can
trust the quality and safety of our furniture and materials, along with the peace of mind
that our products are made to last. If for any reason, you are not satisfied with the
quality and workmanship of our products, we will replace the item or refund the sale.”
Care and Cleaning
Clean unit with a damp cloth or sponge
using warm water and mild soap. Wipe dry.
Do not place near heat, moisture or
vaporizer which may cause panels to warp
and peel.
Check for loose or worn parts periodically
and tighten or replace as necessary.
Record the manufacture date here.
Information is located on the Batch ID
sticker and on the shipping carton.
Save this sheet in an accessible place.
Model Number: ELR-0728
Factory Code: D
Manufacture Date:
Batch ID Number:
(Located on Part C)
If you experience any difficulties with this product, please email us at
[email protected] or call toll-free at [phone]
(Monday - Friday, 7:00am - 4:00pm Pacific Standard Time)
Please do not return to place of purchase as Early Childhood Resources
will replace defective part(s) and/or product.