EarthPulse E-Stim User manual

E-Stim User Guide
Before using the device
New electrode pads should be used with care as user can easily
burn area without knowing. Please check the area every few
minutes to start with especially when pads are new or attached
to sensitive skin.
You agree that you are wishing to do electric experimentation
and assume all responsibility for use of EarthPulse™ systems.
Please return the product if you do not agree as done online. Do
not use the system without reading this manual in its entirety, if
you have any doubts, please contact us.
Please Note:
E-stim is the only square wave electric stim device allowing
both AC and DC use from the same device. In AC mode, it works
like a powerful Beck device (although it can be used at very low
amplitudes too) and in DC mode so it works like a
Becker microampere device too.
Cautions
•Do not use more than 30 mins for first few applications to
avoid Herxheimer’s reaction. Be careful using on sensitive skin
until pads are well used and you are familiar with unit’s power
to avoid burning skin.

•If using like a Beck machine, cut one pair pads in line with
wire and cut to shorten the length so current can be
focused. Secure these small pads in place using tape. Rubber
bands will cut circulation so not good. Or you can put one blue
and one white on opposite sides of the wrist(s) with one pad
directly over pulse point.
•If using as Beck device do not use more than 30 min every
other day to start and an hour per day week two to avoid
Herxheimer reaction.
•This is not a TENS machine.
•This device is permanently set to 9.6Hz regardless of
amplitude setting.
•Always start (ON / OFF toggle) with Amplitude turned to
lowest setting (counter clockwise until stop) and turn up
gradually to comfortable setting once pads are affixed.
•Keep sets of pads together on either side of body. Don’t run
current through the heart but from pad to pad. Set of White /
Blue will run current between them and not though the heart.
Keep pairs of electrodes (white / blue) somewhat close to each
other.
•Two (2) pads can be used rather than two SETS of pads (4).
Leave the un-used pads attached to plastic or leave cable
connectors on unused set with no pads.
•Be sure BARE ends do not touch each other or skin, or
electrical shock can occur.

•White cable pad should never touch blue cable pad or device
will short. Try never to short device.
•The E-Stim gives you enough power to use on larger areas
than any electric stim device we know of and ability to go DC
when AC killing is not needed.
Please Note:
•Use 4 pads to totally surround area or split up and use on two
areas at once.
•Four leads are in two colors - Blue (plus / anode) and White
(minus / cathode). Be sure to use either two or four pads at a
time in pairs of blue/white, not one. Each pair of pads should
have one blue and one white lead. Current will go between any
White and Blue cable so be aware of that when using three
pads if you use that way.
•Give body a day or two between uses so body can catch up if
you find this helpful. Use DC only if AC not needed or if AC
causes more discomfort in area. Body will tell you no AC is
needed and to use DC only. Only you can judge this.
•Use DC at end of each use for at least a few minutes or 1/10
total time or if body says AC is no good due to discomfort.
•In DC mode switch Blue with White cable half way though so
current goes opposite way during application (no need to
switch pad position just cables in AC mode). Only you can tell

which is better if there is a difference for you. In AC mode
switched cables do no good as current goes both ways in AC.
•Research on electric stim will show you this is NOT TENS like
comparing apples to oranges.
•Microcurrent stim can be achieved by using at sub sensory
level. Reduce amplitude to where you can’t feel it, then drop
another 10th turn or so. We found little results with
Microcurrent use though better than nothing. Vision restoration
work can be done at lowest setting. Use AC or DC and you judge
which is better.
•Use on eyes by applying pads to closed eye lids and use at
lowest amplitude. Device was tested amply this way. Normally,
you will “see” light flashing and this is normal. Use comfort level
always. Lowest setting may be used on closed eyes. We did lot
of vision restoration experimentation with the prototype, the
lowest setting is designed for eye lids or microcurrent use
though we feel microcurrent studies and approval was to play
“hide” the ball. Our stim unit adds electrons where they are
needed. Use it wisely.
•Pads may be washed under room temperature water
rubbing sticky side with finger to extend life of pads.