EASTMAN 534 Setup guide

779 Washington St., Buffalo, N.Y. 14203-1396 U.S.A. • [phone] • Fax [phone] or [phone]
Manufacturers of Eastman Cutting and Spreading Machines
[email protected] www.EastmanCuts.com
Instruction Book and
Illustrated Parts List
Please read completely before attempting
to operate your new Cardinal.
Round Knife
Machines
CLASS 534, 548, 562
AND 567
Form C-1063
Eastman®
Eastman
Over a Century of Cutting Expertise
®
Technical Support:
1-800-872-5595
This machine is equipped with a very sharp
knife. Keep hands, arms, and hair away from
the knife area at all times.
Misuse of this machine or failure to follow all
safety instructions on this machine and in the
instruction manual may result in serious per-
sonal injuries.
WARNING
E
A
S
T
M
A
N
®
®
ARDINAL
EASTMAN
R

2Form C-1063
Eastman
®
IMPORTANT
The purchaser must instruct all operators on the proper use of this equipment. All standard
industrial safety measures and equipment should be provided to protect the operator. Opera-
tors must be cautioned that improper or careless use of this equipment may cause personal
injury. If you do not have qualied operators to instruct new persons, contact your EASTMAN
sales representative or EASTMAN factory direct.
Electrical connections and servicing to this equipment should be made by a qualied electri-
cian who is familiar with applicable codes and regulations. Disconnect this equipment from
electrical power source before proceeding with any disassembly for adjustment or repair.
Table of Contents
Safety Information...................................................3
General Safety Precautions..................................3
Safety And Indemnication...................................3
Operation...........................................................4
Maintenance..................................................4
Knife Replacement.........................................4
To Adjust Emery Wheels.......................................5
Replacement Knives...........................................5
Lubrication Maintenance.......................................5
Cardinal Familiarization.............................................6
Guard Assembly......................................................7
Standard Assembly, 4H, 52H And 6H..........................8
Standard Assembly 6X and 75X................................10
Sharpener Assembly................................................12
534 4H and 534BK4H - Single Phase Motors............16
534 4H and 534BK4H - Three Phase Motors.............18
548BK5H and 548CC5H - Single Phase Motors......20
548BK5H and 548CC5H - Three Phase Motors......22
548 52H - Single Phase Motors..................................24
548 52H - Three Phase Motors..................................26
548 6H - Single Phase Motors...................................28
548 6H - Three Phase Motors...................................30
562 6X - Single Phase Motors...................................32
562 6X - Three Phase Motors...................................34
562 75X and 562BK75X - Single Phase Motors........36
562 75X and 562BK75X - Three Phase Motors........38
567 6X - Single Phase Motors..................................40
567 6X - Three Phase Motors...................................42
567 75X and 567BK75X - Single Phase Motors......44
567 75X and 567BK75X - Three Phase Motor........46
534/548 BK And Carpet Cutter Assembly..............48
562/567 BK Assembly..............................................49
Slitter And CC Base Plate Assembly 4H and 5H .....50
Slitter Base Plate Assembly 6X And 75X ...................51
Moistening Attachment With Guard........................ 5 2
Moistening Attachment With Guard 7 1/2". ...........54
RK Push Swivel Handle Assembly 36" ...................56
Stationary Baseplate 548-52H Slitter .....................57
Stationary Baseplate 562/567BK Slitter.................57
Wiring Diagrams......................................................58
Electrical Connections...........................................59
Technical Data.........................................................60

3
Eastman
Over a Century of Cutting Expertise
®
Form C-1063
A warning contains critical information regard-
ing potential safety hazards that can occur dur-
ing proper use or misuse of the machine. Failure
to follow these procedures may result in serious
personal injury to the user.
A caution contains instructions for the use or
maintenance of the machine. Failure to follow
these procedures may result in damage to the
machine.
An electrical hazard calls attention to a proce-
dure, practice, or the like, which, if not correctly
performed or adhered to, could result in personal
injury. Do not proceed beyond an Electrical Haz-
ard.
During the life of the machine, the purchaser agrees
to provide to all machine users (including its own
employees and independent contractors) all rel-
evant safety information, including warning labels
and instruction manuals. The purchaser also agrees
to maintain the safety features and working condi-
tion of the machine, and to adequately train all users
in the safe use and maintenance of the machine.
The purchaser agrees to defend, protect, indem-
nify, and hold Eastman Machine Company and its
subsidiaries harmless from and against all claims,
losses, expenses, damages, and liabilities to the ex-
tent that they have been caused by the purchaser’s
failure to comply with the terms and instructions of
this manual.
• Do not modify this machine or disable safety
features. Unauthorized modication may result
in serious personal injuries to the user. Electri-
cal connections to this machine must be made
by a qualied electrician familiar with applicable
codes and regulations.
• Safety labels must be kept clean and legible at
all times. Call the Eastman Machine factory to
order replacement labels.
WARNING
ELECTRICAL HAZARD
CAUTION
• This machine is equipped with very sharp and
dangerous tools. Keep hands, arms, and hair
away from the cutting area and drive system at
all times. Safety gloves, glasses, and appropri-
ate clothing may prevent serious personal inju-
ries.
• Disconnect the power supply to the machine
when it is not in use or during routine mainte-
nance, including cleaning and lubrication.
• The purchaser must instruct all operators in the
proper use of the machine according to the in-
structions in this manual. This training must in-
clude instruction on the potential safety hazards
arising from the use or misuse of the machine. In
addition to such training, the purchaser should
provide written work instructions as necessary
to ensure correct use of the machine for specic
cutting and spreading applications.
General Safety Precautions
WARNING
Safety and Indemnication
Safety Information
Throughout this manual, safety information is presented
by the use of the terms WARNING, CAUTION, ELECTRI-
CAL HAZARD, and NOTE. These terms have the follow-

4Form C-1063
Eastman
®
MAINTENANCE
CAUTION
Before performing any of the following procedures make
sure that the attachment is disconnected from this system.
Knife Motor
WARNING
This machine is equipped with a sharp knife. Keep hands
away from knife area at all times. Use handle and control
lever when operating or handling the machine. Knife guard
should be raised only enough to clear the material being
cut. When not in use, knife guard should be set at the low-
est position. DO NOT OPERATE THIS MACHINE WITH
KNIFE GUARD REMOVED.
Maintenance Procedures
1. Be sure that the rollers of the base plate are kept free
of debris.
2. Be sure that the terminal pins on the terminal block are
kept in good condition to make full contact with the female
receptacle.
3. Inspect the operating switch periodically to make sure
that it is making full contact when in the "ON" position.
4. When replacing the knife on this cutting unit, be sure
that any cutting debris between the knife and the standard
is cleaned out.
5. If the cutting unit seems to lag while not cutting, the knife
should be removed and the unit should be run without the
knife to see if the machine has been over-greased or is
there is an obstruction somewhere.
Knife Sharpening
Take the machine out of the material to be cut. Switch
power to ON position (use CAUTION when sharpening
blade). To obtain a ne, keen edge on the blade, press
and hold sharpener trigger lightly, the sharpening stones
will contact the blade. Press and hold trigger with constant
pressure for 10 seconds, then release. Repeat process as
necessary.
D
F
E
L
C
K
Knife Replacement
WARNING
This knife is very sharp. Failure to follow proper precau-
tions when handling may result in serious injury. Discard
used knife with care!
Loosen thumb screw "E" and swing guard "F" to outward
position as shown on dotted lines. Turn the knife so the
small hole lines up with hole "G" in the standard. Insert
the small pin that is with the supplies in hole "G." Remove
the lock nut that retains the blade with the special spanner
wrench. When installing a new knife, be sure the name
"Eastman Machine Company" is facing outward, and that
the knife seats on the gear. Install knife lock nut and be
sure that throat plate is adjusted as outlined.
SPANNER WRENCH
SMALL PIN
PART NO. BLADE DIA.
95C1-12 4",5"
95C1-13 5 1/4",6", 7 1/2"
PART NO.
17C11
OPERATION
Turn the switch to the on position; if cutter does not start
immediately, return the switch to the off position. Check the
line output and be sure that the unit is plugged in properly
and is making full contact, then repeat procedure. Do not
attempt to start this unit while it is in the material being cut.

5
Eastman
Over a Century of Cutting Expertise
®
Form C-1063
L
G
H
F
K
B
J
E
D
C
A
To Adjust the Throat Plate
It is very important that the edge of the knife be as close as
possible without touching to the forward position in the slot
on the throat plate. The slot in the throat plate "J" should
straddle the blade and screws "H" can be loosened and
re-tightened to accomplish this adjustment.
To Adjust Emery Wheels
As the Emery Wheels wear away and become farther
apart, they must be adjusted. Adjust Emery Wheels from
both sides to assure proper centering of the wheels over
the knife. Proceed as follows:
1. Loosen slotted head screws "K."
2. With ngers, turn adjusting bushings "L" until Emery
Wheels are as close together as possible without touching,
and are centered over the knife. Both wheels should grind
at the same time when pressed lightly against the knife
and there should be no more than 1/32"-inch clearance
between the two Emery Wheels.
3. Tighten slotted head screws "K".
To Replace Emery Wheels
1. With front of machine facing serviceman, guard rod in
down safe position, remove right hand grinding wheel and
arm by loosening screw "D" and sliding arm off shaft.
2. Remove slotted head screw "C" and replace grinding
wheel with spindle in right hand arm.
3. No need to remove left hand arm from machine. Remove
slotted head screw "C" from left hand arm and replace
grinding wheel with spindle.
4. Re-assemble right hand arm to shaft and adjust wheels
to knife as covered above.
CAUTION
Do not use sewing machine oil or detergent oil. It is
entirely too light for cutting machine lubrication. For
best results use specially compounded Eastman Oil.
Do not oil base plate rollers.
We recommend our Eastman Gear Lubricant special
formula (242C2) for gears and Eastman Lubriko grease
(242C2-2) for knife gear ball bearings. Do not use East-
man Gear Lubricant for ball bearings, or Eastman Lu-
briko grease for gears.
Carbon
Steel
80C1-59 1
80C1-101 1
80C1-61 1
80C1-39 1
80C1-77/100 1
High Speed
Steel
80C1-59 2
80C1-101 2
80C1-61 2
80C1-39 2
80C1-77/100 2
High Speed
Steel Grooved
80C1-59 5
80C1-101 5
80C1-61 5
80C1-39 5
80C1-77/100 5
High Speed Steel
Teon Coated
80C1-59 6
80C1-101 6
80C1-61 6
80C1-39 6
80C1-77/100 6
Knife
Diameter
4
5
5-1/4
6
7-1/2
Carbon
Slotted
-
-
-
-
80C1-120 1
Dbl-Bevel
Hi-Speed
-
-
-
-
80C1-154 6
Replacement Knives
Lubrication Maintenance
TWICE A DAY ONCE A DAY
Oil Emery Wheel Spindles
at location
"C."
DO NOT USE AN EXCESS
AMOUNT OF OIL
Lubricate gears, screw
grease cup "A" down
one-half turn.
Rell cup, as required with
Eastman Gear Lubricant,
special formula:
(242C2)

6Form C-1063
Eastman
®
Guard Assembly
See Page 7
Sharpener Assembly
See Pages 12
Motor Assembly
See Pages 16-47
Base Plate Assembly
See Pages 14-15
Standard Assembly
See Pages 8-11
E
A
S
T
M
A
N
®
®
Cardinal Familiarization

7
Eastman
Over a Century of Cutting Expertise
®
Form C-1063
8
9
1
2
3
4
6
7
5
Guard Assembly
(A) 699C1-3 (534 4H and 534BK4H)
(B) 699C1-4 (548BK5H, 548CC5H and 548 52H)
(C) 699C1-5 (548 6H)
(D) 699C1-6 (562 6X and 567 6X)
(E) 699C1-7 (562 75X and 567 75X)
ITEM PART NO. DESCRIPTION QTY.
1 4C2-93 Spline Nut 1
2A 62C9-81 Guard Rod Holder Bracket 1
2B 62C9-80 Guard Rod Holder Bracket 1
2C 62C9-80 Guard Rod Holder Bracket 1
2D 62C9-85 Guard Rod Holder Bracket 1
2E 62C9-85 Guard Rod Holder Bracket 1
3A 33C4-23 Guard Rod Holder 1
3B 33C4-23 Guard Rod Holder 1
3C 33C4-24 Guard Rod Holder 1
3D 33C4-26 Guard Rod Holder 1
3E 33C4-26 Guard Rod Holder 1
4 20C4-38 Lock Screw 1
5 17C15-123 Pin 1
6 12C15-103 Washer 1
7A 65C2-66 Guard Rod 4" Knife 1
7B 65C2-67 Rod Knife Guard 5-6 1
7C 65C2-67 Rod Knife Guard 5-6 1
7D 65C2-35 Rod Knife Guard 6X 1
7E 65C2-50 Rod Knife Guard 75X 1
8 20C5-2 Guard Rod Screw 1
9 300C12-13 Screw,Rd.Hd.#8-32 X 5/16 2
Item numbers are for reference only.
Please Specify MODEL SERIAL
NUMBER and PART NUMBER when
ordering replacement parts.

8Form C-1063
Eastman
®
Standard Assembly, 4H, 52H and 6H
(A) 534 4H
(B) 548 52H
(C) 548 6H
ITEM PART NO. DESCRIPTION QTY.
17A 20C4-29 Bearing Lock Screw 4"/5" 1
17B 20C4-28 Bearing Lock Screw 5-1/4"/6" 1
17C 20C4-28 Bearing Lock Screw 5-1/4"/6" 1
18A 4C1-114 Bearing Locking Nut 4"/5" 1
18B 4C1-113 Bearing Locking Nut 5-1/4"/6" 1
18C 4C1-113 Bearing Locking Nut 5-1/4"/6" 1
19A 4C1-81 Knife Lock Nut 4"/5" 1
19B 4C1-82 Knife Lock Nut 5-1/4" 6" 1
19C 4C1-82 Knife Lock Nut 5-1/4" 6" 1
20A 216C1-2 Bearing Seal 4"/5" 1
20B 216C1-1 Bearing Seal 5-1/4" 6" 1
20C 216C1-1 Bearing Seal 5-1/4" 6" 1
Item numbers are for reference only.
Please Specify PART NUMBER when
ordering replacement parts.
ITEM PART NO. DESCRIPTION QTY.
1A 531C1-13 Operating Handle 1
1B 531C1-53 Operating Handle 1
1C 531C1-53 Operating Handle 1
2A 4C1-115 Operating Handle Lock Nut 1
2B 4C1-130 Operating Handle Lock Nut 1
2C 4C1-130 Operating Handle Lock Nut 1
3B 57C1-56 Switch Lever 1
3C 57C1-56 Switch Lever 1
4B 302C12-2 Screw, Flat, Hd #8-32 x 5/16 1
4C 302C12-2 Screw, Flat, Hd #8-32 x 5/16 1
5 17C1-4 Standard Pin 2
6 4C4 Side Guide Nut 1
7 72C4-20 Grease Cup 1
8A 53C4-64 Gear Cover 4H 1
8B 53C4-36 Gear Cover 52H 1
8C 53C4-47 Gear Cover 6H 1
9 300C12-7 Screw, Rd. Hd. #8-32 x 5/8 2
10B 13C2-5 Switch Lever Knob 1
10C 13C2-5 Switch Lever Knob 1
11A 511C1-97 Standard Complete 4H 1
11B 511C1-96 Standard Complete 52H 1
11C 511C1-101 Standard Complete 6H 1
12A 12C9-8 Knife Gear Shim 4H 1
12B 12C9-7 Knife Gear Shim 52H 6H 1
12C 12C9-7 Knife Gear Shim 52H 6H 1
13A 25C4-137 Side Guard 4" 1
13B 25C4-138 Side Guard 5-1/4" 1
13C 25C4-140 Side Guard 6" 1
14 24C6 Side Guard Screw 1
15A 521C1-37 Gear Set and Bearing 4H/5H 1
15B 521C1-21 Gear Set and Bearing 52H/6H 1
15C 521C1-21 Gear Set and Bearing 52H/6H 1
16A 90C6-9 Knife Gear Bearing 4H/5H 1
16B 90C6-33 Knife Gear Bearing 52H/6H 1
16C 90C6-33 Knife Gear Bearing 52H/6H 1

9
Eastman
Over a Century of Cutting Expertise
®
Form C-1063
1
2
3
4
5
6
8
7
9
10
12
11
13 14
15
16
17
18
19
20
Part of
675C1-11 4H/5H
675C1-14 52H/6H
For Knife Options
See Page 5

10 Form C-1063
Eastman
®
Standard Assembly 6X and 75X
(A) 562 6X and 567 6X
(B) 562 75X and 567 75X
Item numbers are for reference only.
Please Specify PART NUMBER when
ordering replacement parts.
ITEM PART NO. DESCRIPTION QTY.
1 531C1-53 Operating Handle 1
2 4C1-111 Operating Handle Lock Nut 1
3 29C6-50 Handle Adapter 1
4 17C1-4 Standard Pin 2
5 72C4-20 Grease Cup 1
6A 511C1-64 Standard Complete 6X 1
6B 511C1-63 Standard Complete 75X 1
7A 25C4-93 Side Knife Guard 6X 1
7B 25C4-59 Side Knife Guard 75X 1
8 20C7-1 Screw, Thumb 1
9 302C7-2 Screw,Flt.Hd.#4-36 X 1/4 4
10 53C4-52 Gear Cover 6X/75X 1
11A 20C4-26 Inter Screw Lock 1
11B 20C4-38 Inter Screw Lock 1
12 4C1-103 Locknut Inter Gear 1
13 87C5-14 Gear Intermediate 1
14 308C8-1 Screw,Skt.Hd.#4-40 X 1/4 6
15 90C6-9 Ball Bearing 1
16 521C1-26 Gearing/Bearing Set 6X/75X 1
17 87C2-25 Gear Knife 6X/75X 1
18 90C6-33 Ball Bearing 1
19 20C4-30 Screw Lock Knife Bearing 1
20 4C1-113 Locknut Knife Gear Bearing 1
21 4C1-82 Knife Locknut

11
Eastman
Over a Century of Cutting Expertise
®
Form C-1063
1
2
3
4
5
67
8
15
13
12
11
10
9
16
20
19
18
For Knife Options
See Page 5
21
14
Part of
675C1-16 6X/75X
17

12 Form C-1063
Eastman
®
Sharpener Assembly
(A) 637C1-25 - 4" Round Knife
(B) 517C1-26 - 5" Round Knife
(C) 517C1-27 - 5 1/4" Round Knife
(D) 517C1-28 - 6" Round Knife
(E) 637C1-30 - 7 1/2" Round Knife
ITEM PART NO. DESCRIPTION QTY.
23 35C5-57 Arm Sharp Rd. Knife LH 1
24 300C10-5 Screw, Rd. Hd. #6-32 x 7/16 1
25 20C6-11 Screw, Emery Adjusting Whl. 1
26 304C10-3 Screw,Truss, Hd. #6-32x3/16 1
27A 25C4-160 Knife Guard 4" 1
27B 25C4-161 Knife Guard 5 1/4" 1
27C 25C4-161 Knife Guard 5 1/4" 1
27D 25C4-163 Knife Guard 6" 1
27E 25C4-163 Knife Guard 6" 1
28 300C8-8 Screw, Rd. Hd. #4/40 X 5/16 2
29 541C1-XX See Chart 2
30 92C1-12 Spindle Grind Whl 1
31 12C15-70 Washer,Paper 1
32 12C1-28 Washer,Lock,Special 1
33 20C13-20 Screw,Oval Hd.#8-32 X 3/8 1
34 133C1-XX See Chart 1
Emery Wheel Options
133C1-11 120 Grit 4" Knife
133C1-12 120 Grit 5"/5-1/4"/6"/6x/75x Knife
133C1-13 150 Grit 4" Knife
133C1-14 150 Grit 5"/5-1/4"/6"/6x/75x Knife
133C1-24 220 Grit 4" Knife
133C1-25 220 Grit 5"/5-1/4"/6"/6x/75x Knife
Emery Wheel Assembly Options
541C1-9 120 Grit 5"/5-1/4"/6"/6x/75x Knife
541C1-10 120 Grit 4" Knife
541C1-13 150 Grit 5"/5-1/4"/6"/6x/75x Knife
541C1-14 150 Grit 4" Knife
541C1-20 220 Grit 5"/5-1/4"/6"/6x/75x Knife
541C1-21 220 Grit 4" Knife
ITEM PART NO. DESCRIPTION QTY.
1 17C15-71 Pin,Cotter 1/16 X 1/2 2
2 77C1-67 Link Sharp Contact 1
3 57C2-17 Lever Sharp 3
4 20C8-2 Screw, Sharpener Arm Pivot 1
5 34C1-20 Spring Tension 1
6 309C12-3 Screw, Skt, Set #8-32 X 3/8 1
7 46C3-13 Block Sharpener Arm 534 1
7A 46C3-22 Block Sharpener Arm 4 1
8 11C10-19 Sharpener Shaft 1
9 302C12-3 Screw,Flt.Hd.#8-32 X 3/8 Sp. 2
10 12C15-29 Washer, Flat 2
11A 636C1-8 Sharpener Bracket Assy 4" 1
11B 636C1-9 Sharpener Bracket Assy 5" 1
11C 636C1-10 Sharpener Bracket Assy 5 1/4 1
11D 636C1-11 Sharpener Bracket Assy 6" 1
11E 636C1-13 Sharpener Bracket Assy 7 1/2 1
12 300C12-3 Screw, Rd. Hd. #8-32 X 3/8 1
12E 308C12-1 Screw, Skt. Hd. #8-32 X 3/8 1
13 12C1-21 Washer, Lock #8 1
14A 540C1-53 Arm Emery Wheel RH4 1
14B 540C1-54 Arm Emery Wheel RH5&5 1/4 1
14C 540C1-54 Arm Emery Wheel RH5&5 1/4 1
14D 540C1-55 Arm Emery Wheel RH6 1
14E 540C1-56 Arm Emery Wheel RH7 1/2 1
15 300C8-8 Screw, Rd. Hd. #4-40 x 5/16 2
16A 25C4-160 Knife Guard 4" 1
16B 25C4-161 Knife Guard 5 1/4" 1
16C 25C4-161 Knife Guard 5 1/4" 1
16D 25C4-163 Knife Guard 6" 1
16E 25C4-163 Knife Guard 6" 1
17 304C10-3 Screw,Truss, Hd. #6-32x3/16 1
18 20C6-11 Screw, Emery Adjusting Whl. 1
19 35C5-65 Arm Sharp Rd. Knife RH 1
20 300C10-5 Screw, Rd. Hd. #6-32 x 7/16 1
21A 540C1-45 Arm Emery Wheel LH4 1
21B 540C1-47 Arm Emery Wheel LH5&5 1/4 1
21C 540C1-47 Arm Emery Wheel LH5&5 1/4 1
21D 540C1-49 Arm Emery Wheel LH6 1
21E 540C1-51 Arm Emery Wheel LH7 1/2 1
22 309C12-3 Screw, Skt, Set #8-32 x 3/16 1
Item numbers are for reference only.
Please Specify MODEL SERIAL
NUMBER and PART NUMBER when
ordering replacement parts.

13
Eastman
Over a Century of Cutting Expertise
®
Form C-1063
1
1
2
3
4
6
7
58
9
10
11
10
23
21
24
25
26
22
28
27
30
31
34 32
33
29
12
13
20 18
19
17 15
16
14

14 Form C-1063
Eastman
®
ITEM PART NO. DESCRIPTION QTY.
1A 76C2-44 Filler Plate 1
1B 76C2-44 Filler Plate 1
1C 76C2-49 Filler Plate 6X 1
2A 538C1-74 Plate Flat & Wing 1
2B 538C1-79 Plate Flat & Wing 1
2C 538C1-61 Plate Flat & Wing 1
3 302C14-11 Screw,Flt.Hd.#10-24 X 1/2 2
4 20C13-72 Screw, Base Plate to Stand. 3
5 300C10-3 Screw,Rd.Hd.#6-32 X 5/16 4
6 12C15-3 Throat Plate Washer 4
7 622C1-2 Roller Plate Front 14
8 18C6-10 Ring Rubber 8
9 12C8-1 Washer,Plate Roller 8
10 41C2 Roller Plate 40
11 61C1-1 Shell Plate Roller 4
12 11C2-4 Shaft Plt Roller 4
13 98C4-12 Clip Roller Shaft 2
14 98C4-11 Clip Roller Shaft 2
15 302C10-1 Screw,Flt.Hd.#6-32 X 3/16 10
16 79C5-XXX See Chart 1
10
11
12
14
15
9
8
8
9
8
9
9
8
12
13
15
11
10
5
4
3
2
1
6
16
7
7
Base Plate Assembly 4H, 52H and 6H
(A) 505C3-191 E (548 52H and 548 6H)
(B) 505C3-203 E (534 4H)
(C) 505C3-150 E (562 6X and 567 6X)
THROAT PLATES
79C5-155 4" and 5-1/4" Knife
79C5-184 6" Knife
79C5-185 5" Knife
79C5-188 6X and 75X Knife
Item numbers are for reference only.
Please Specify MODEL SERIAL
NUMBER and PART NUMBER when
ordering replacement parts.

15
Eastman
Over a Century of Cutting Expertise
®
Form C-1063
Base Plate and Roller Assembly 6X and 75X
505C3-51 E (562 75X and 567 75X)
1
3
5
6
4
16
19
17
18
17
20
16
17
18
17
19
13 14
13 14
8
9
13 14
9
12
8
11
10
7
15
2
ITEM PART NO. DESCRIPTION QTY.
1 76C2-21 Filler Plate 7L&75X 1
2 79C5-188 Throat Plate 6X and 75X 1
3 538C1-25 Plate Flat & Wing 1
4 305C14-1 Scrw,Binding Hd.#10-24X3/8 2
5 12C15-3 Throat Plate Washer 4
6 300C10-3 Screw,Rd.Hd.#6-32 X 5/16 4
7 622C1-4 Roller Plate Front 2
8 18C6-10 Ring Rubber 4
9 12C8-1 Washer,Plate Roller 4
10 11C2-13 Shaft Plt Roller 2
11 41C2-7 Roller Plate 20
12 61C1-5 Shell Plate Roller 2
13 98C4-11 Clip Roller Shaft 4
14 302C10-1 Screw,Flt.Hd.#6-32 X 3/16 8
15 619C1-8 Roller Plate Rear 1
16 41C2-7 Roller Plate 20
17 12C8-1 Washer,Plate Roller 4
18 61C1-5 Shell Plate Roller 2
19 18C6-10 Ring Rubber 4
20 11C2-14 Shaft Plt. Roller 1
Item numbers are for reference only.
Please Specify MODEL SERIAL
NUMBER and PART NUMBER when
ordering replacement parts.

16 Form C-1063
Eastman
®
534 4H and 534BK4H - Single Phase Motors
(A) 517C1-1236 - (110V, 60Hz, 1Ph, 2Pole)
(B) 517C1-1029 - (110V, 60Hz, 1Ph, 4Pole)
(C) 517C1-1238 - (220V, 50Hz, 1Ph, 2Pole)
(D) 517C1-1237 - (220V, 60Hz, 1Ph, 2Pole)
ITEM PART NO. DESCRIPTION QTY.
1 4C1-87 Locknut Front Bearing 1
2 90C6-29 Bearing Ball 1
3 90C2-146 Bearing Housing, Front 1
4 10C2-30 Fan, Rotor 1
5 513C3-238 Rotor Shaft 534 4H 1
6A 514C4-241 Stator & Band, 1106012 1
6B 514C4-221 Stator & Band, 1106014 1
6C 514C4-243 Stator & Band, 2205012 1
6D 514C4-242 Stator & Band, 2206012 1
7A 90C1-158 Bearing Housing, Rear 534 1
7B 582C2-58 Bearing Housing, Rear 534 1
7C 90C1-158 Bearing Housing, Rear 534 1
7D 582C2-58 Bearing Housing, Rear 534 1
8 4C1-118 Locknut, Rear Bearing 1
9A 597C2-21 Cut-Out Auto 60CY 2PL 1
9B 597C2-23 Cut-Out Auto 60CY 4PL 1
9C 597C2-22 Cut-Out Auto 50CY 2 PL 1
9D 597C2-21 Cut-Out Auto 60CY 2PL 1
10 580C1-70 Cut-Out Switch 625 1
11 300C12-3 Scr. Round Hd. #8-32x3/8 2
12 8C5-10 Insulation for Switch 1
13 90C6-46 Bearing Ball 1
ITEM PART NO. DESCRIPTION QTY.
14 12C1-12 Washer, Loading Spring 1
15 20C3-37 Screw 534 4
16 53C7-39 Cover, Rear Bearing 534 1
17 301C10-3 Scr. Round Hd. #6-32x3/8 3
18 4C1-180 Nut Bearing Screw 4
19 675C1-11 Gear Set, 4H & 5H 1
20 302C15-8 Scr. Flat Hd. #10-32x1&1/8 2
21 53C2-107 Switch Cover 534 1
22 300C10-4 Scr. Round Hd. #6-32x3/8 2
23 8C4-20 Switch Insulation 1
24 580C1-85 Switch, On/Off 1
25 52C5-175 Switch Base (Bracket) 1
26 300C10-2 Scr. Round Hd. #6-32x1/4 2
27 8C4-72 Switch Insulation 1
28 305C10-1 Scr. Binding Hd. #6-32x1/4 1
29 12C1-32 Washer, Lock #6 1
30 783C1-3 Ground Wire Asm. (Grn/Yel) 1
31 12C11-17 Spacing Washer A/R
32 1C5-32 Drive Gear Spacing Sleeve 1
33 22C1-33 Carrying Handle 1
34 300C14-4 Screw, Rd. Hd. #10-24 X 1/2 2
A/R = As Required
Item numbers are for reference only.
Please Specify MODEL SERIAL
NUMBER and PART NUMBER when
ordering replacement parts.

17
Eastman
Over a Century of Cutting Expertise
®
Form C-1063
5
6
7
8
9
10
11
12
13
14
16
17
20
21
22
23
24
25
26
27
28
30
1
2
3
4
18
31
32 19
29
15
33
34
Part of 675C1-11
See Page 59 for Complete Parts List

18 Form C-1063
Eastman
®
534 4H and 534BK4H - Three Phase Motors
(A) 517C1-1147 - (220V, 50Hz, 3Ph, 2Pole)
(B) 517C1-1239 - (220V, 60Hz, 3Ph, 2Pole)
(C) 517C1-1281 - (380V, 60Hz, 3Ph, 4Pole)
ITEM PART NO. DESCRIPTION QTY.
1 4C1-87 Locknut Front Bearing 1
2 90C6-29 Bearing Ball 1
3 90C2-146 Bearing Housing, Front 1
4 10C2-30 Fan, Rotor 1
5A 513C1-221 Rotor Shaft 534 4H 1
5B 513C1-238 Rotor Shaft 534 4H 1
5C 513C1-238 Rotor Shaft 534 4H 1
6A 514C4-125 Stator & Band, 2205032 1
6B 514C4-244 Stator & Band, 2206032 1
6C 514C4-260 Stator & Band, 3806034 1
7 90C1-158 Bearing Housing, Rear 1
8 4C1-118 Locknut, Rear Bearing 1
9 4C1-180 Nut Bearing Screw 4
10 675C1-11 Gear Set, 4H & 5H 1
11 302C15-8 Scr. Flat Hd. #10-32x1&1/8 2
12 1C4-10 Sleeve Cutout, 548 1
13 90C6-46 Bearing Ball 1
14 12C1-12 Washer, Loading Spring 1
15 20C3-37 Screw 534 4
ITEM PART NO. DESCRIPTION QTY.
16 53C7-39 Cover, Rear Bearing 1
17 301C10-3 Scr. Round Hd. #6-32x3/8 3
18 305C10-1 Scr. Binding Hd. #6-32x1/4 1
19 12C1-32 Washer, Lock #6 1
20 783C1-3 Ground Wire Asm. (Grn/Yel) 1
21 300C14-4 Screw, Rd. Hd. #10-24 X 1/2 2
22 53C2-107 Switch Cover 534 1
23 300C10-4 Scr. Round Hd. #6-32x3/8 2
24 8C4-20 Switch Insulation 1
25 580C1-85 Switch, 1Ph 1
26 52C5-175 Switch Mounting Bracket 1
27 300C10-2 Scr. Round Hd. #6-32x1/4 2
28 8C4-72 Switch Insulation 1
29 12C11-17 Spacing Washer A/R
30 1C5-32 Drive Gear Spacing Sleeve 1
31 22C1-33 Carrying Handle 1
A/R = As Required
Item numbers are for reference only.
Please Specify MODEL SERIAL
NUMBER and PART NUMBER when
ordering replacement parts.

19
Eastman
Over a Century of Cutting Expertise
®
Form C-1063
1
2
3
4
5
6
7
8
13
14
16
17
9
11
12
23
24
25
26
27
28
21
18
20
22
29
30 10
19
15
31
Part of 675C1-11
See Page 59 for Complete Parts List

20 Form C-1063
Eastman
®
548BK5H and 548CC5H- Single Phase Motors
(A) 517C1-1048 - (110V, 50Hz, 1Ph, 2Pole)
(B) 517C1-1101 - (110V, 60Hz, 1Ph, 2Pole)
(C) 517C1-1051 - (110V, 60Hz, 1Ph, 4Pole)
(D) 517C1-1106 - (220V, 50Hz, 1Ph, 2Pole)
(E) 517C1-1109 - (220V, 50Hz, 1Ph, 4Pole)
(F) 517C1-1049 - (220V, 60Hz, 1Ph, 2Pole)
ITEM PART NO. DESCRIPTION QTY.
1 4C1-87 Locknut Front Bearing 1
2 90C6-29 Bearing Ball 1
3 90C2-143 Bearing Housing, Front 1
4 10C2-27 Fan, Rotor 1
5 513C3-233 Rotor Shaft 548 5H 1
6A 514C4-209 Stator & Band, 1105012 1
6B 514C4-206 Stator & Band, 1106012 1
6C 514C4-221 Stator & Band, 1106014 1
6D 514C4-208 Stator & Band, 2205012 1
6E 514C4-212 Stator & Band, 2205014 1
6F 514C4-207 Stator & Band, 2206012 1
7 589C2-56 Bearing Housing, Rear 1
8 4C1-118 Locknut, Rear Bearing 1
9A 597C2-22 Cut-Out Auto 50CY 548 1
9B 597C2-21 Cut-Out Auto 60CY 548 1
9C 597C2-23 Cut-Out Auto 60CY 4PL 1
9D 597C2-22 Cut-Out Auto 50CY 548 1
9E 597C2-24 Cut-Out 50CY 4PL 1
9F 597C2-21 Cut-Out Auto 60CY 548 1
10 580C1-70 Cut-Out Switch 625 1
11 300C12-3 Scr. Round Hd. #8-32x3/8 2
ITEM PART NO. DESCRIPTION QTY.
12 8C5-10 Insulation for Switch 1
13 90C6-46 Bearing Ball 1
14 12C1-12 Washer, Loading Spring 1
15 20C3-34 Screw, Bearing (Special) 4
16 53C7-36 Cover, Rear Bearing 548 1
17 301C10-3 Scr. Round Hd. #6-32x3/8 3
18 4C1-186 Nut Bearing Screw 4
19 675C1-11 Gear Set, 4H & 5H 1
20 302C15-8 Scr. Flat Hd. #10-32x1&1/8 2
21 53C2-104 Switch Cover 3Ph 548 1
22 300C10-4 Scr. Round Hd. #6-32x3/8 2
23 8C4-41 Switch Insulation 1
24 580C1-85 Switch, On/Off 1
25 52C5-171 Switch Mounting Bracket 1
26 300C10-2 Scr. Round Hd. #6-32x1/4 2
27 8C4-72 Switch Insulation 1
28 305C10-1 Scr. Binding Hd. #6-32x1/4 1
29 12C1-32 Washer, Lock #6 1
30 783C1-3 Ground Wire Asm. (Grn/Yel) 1
31 12C11-17 Spacing Washer A/R
32 1C5-33 Drive Gear Spacing Sleeve 1
33 22C1-32 Carrying Handle 1
34 300C14-4 Screw, Rd. Hd. #10-24 X 1/2 2
A/R = As Required
Item numbers are for reference only.
Please Specify MODEL SERIAL
NUMBER and PART NUMBER when
ordering replacement parts.