EASTMAN RS2 User manual

779 Washington St., Buffalo, N.Y. 14203-1396 U.S.A. • [phone] • Fax [phone] or [phone]
Manufacturers of Eastman Cutting and Spreading Machines
www.EastmanCuts.com
Instruction Book
and Parts List
Please read completely before attempting
to operate your new RS2 Cutting Machine.
RUBBER
SLITTER
Form C-1519
Technical Support:
1-800-872-5595
[email protected]
This machine is equipped with a very sharp
knife. Keep hands, arms, and hair away from
the knife area at all times.
Misuse of this machine or failure to follow all
safety instructions on this machine and in the
instruction manual may result in serious per-
sonal injuries.
WARNING
MODEL RS2
Safety glasses must be worn at all times when
operating or servicing this equipment.
WARNING
SILAC - Italy

2Form C-1519
Before operating machine, read these instructions care-
fully. Familiarize yourself with all functions and adjust-
ments of this equipment.
Operation,
Lubrication
And Care
The purchaser must instruct all operators on the proper
use of the equipment. All standard industrial safety mea-
sures and equipment should be provided to protect the
operator. Operators must be cautioned that improper use
of this equipment can cause bodily injury. If you do not
have qualied operators to instruct new persons, contact
your Eastman sales representative or write to Eastman
Machine factory direct.
CAUTION
Read instructions carefully before starting motor. Be
sure that voltage and current are the same as stamped
on nameplate. This machine is equipped with sharp
blade and extreme caution should be used when this
machineisputintouse. Usecontrolleversandhandles
only when operating or handling machine. When mak-
ing a cut, the knife guard should be raised only enough
to clear the material being cut. When machine is not
in operation the front knife guard should be kept in the
lowered position and lubricator turned off. When this
equipmentisnotbeingutilized,thepowersupplyshould
be disconnected from the equipment.
OPERATING INSTRUCTIONS
Loosen thumb screw for adjustment of knife guard and
spongeholder. Raiseguard enoughto clearmaterial tobe
cut. Turn sight tube valve counterclockwise for lubrication
of knife. Switch machine to ON position, if cutter does not
startimmediately,returnswitchtoOFFposition. Checkthe
line output and be sure the unit is plugged in properly and
is making full contact. Then repeat procedure. DO NOT
attempt to start this unit while in material to be cut. After
knife has gathered full speed, material can now be cut. To
keepfrictionandheat builduptoaminimumacombination
of low speed and ow of lubricant are used. The blade
speed setting, depending on operator preference, can be
decreasedbyturningthespeedcontrolknobcounterclock-
wisetoalowernumber(0=65RPM)orincreasebyturning
clockwise to a higher setting (10 = 150 RPM).
Limited Warranty. Eastman warrants to the buyer that the RS2 Rubber Slitter shall be free from defects in materials
or workmanship for a period of 90 days commencing on the date of invoice. Any goods or parts claimed by the buyer
to be defective must be returned to Eastman, freight charges prepaid, within the 90-day warranty period. If Eastman
determines that the goods or parts are defective in materials or workmanship, Eastman’s sole obligation under this
warranty shall be, at Eastman’s sole option, to repair or replace the defective goods or parts or to provide the buyer
a credit equal to the portion of the purchase price allocable to the defective goods or parts. This warranty shall not
apply if defects are caused by product misuse or neglect, if the machine has been altered or modied by the buyer,
or if other than genuine Eastman parts are used in the machine. THIS WARRANTY IS THE ONLY WARRANTY
APPLICABLE TO THIS PURCHASE. SELLER DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE.
Limitation of Liability. Eastman’s liability to the buyer, and the buyer’s remedies from Eastman, whether in contract,
negligence, tort, under any warranty or otherwise, shall be limited to the remedies provided in the foregoing Limited
Warranty. In no event shall Eastman have any responsibility or liability to the buyer for (a) any special, indirect,
incidental, or consequential damages, including, but not limited to, loss of use, revenue, or prot, even if Eastman
has been advised of the possibility of such damages, or (b) any claim against the buyer by any third party. The price
stated for the product sold is a consideration for limiting Eastman’s liability.
SILAC - Italy

Form C-1519 3
MAINTENANCE PROCEDURES
1. Be sure the baseplate rollers are kept lint free.
2. Be sure the terminal pins on the terminal block are in
good condition to make full contact with the female
receptacle.
3. Inspect the operating switch periodically for full contact
when in the ON position.
4. When replacing the knife on this cutting unit, remove
any lint build-up between the knife and the standard.
5. Ifthecuttingunitseemstolagwhilenotcutting,theknife
should be removed and the unit should be run without
the knife to see if the machine has been overgreased
or if there is an obstruction somewhere.
OPTIONAL
The RS2 Rubber Slitter has been designed for quick and
easy conversion between the standard Baseplate and the
optionalStripGauge. Tomake the conversion;disconnect
the power attachment plug. Remove (5) screws, (308C15-
2)and (308C15-3) betweenthe bracketandstandard.The
new strip gauge can now be mounted using the same (5)
screwsand readyfor useinminutes asshown onpage 18.
Strip gauge operation is identical to that of the standard
Baseplate with the added advantage of a Strip Gauge for
cutting strips up to 11" wide and
1 1/2" thick.
KNIFE SHARPENING
Takethemachineoutof materialtobecut.Switchmachine
toON position,note settingofvariable speedand increase
speed to full capacity. To obtain a ne, keen edge on blade,
press lightly on sharpener lever with a constant pressure.
Hold lever until blade is sharp, then release. Return vari-
able speed setting to cutting speed.
TO REPLACE THE KNIFE
Loosen thumb screw and slide guard to upward position.
Turn the knife so the small hole lines up with hole in the
standard and insert knife removal pin (17C11) into hole.
Loosen three (3) setscrews in the locknut and remove the
locknut that retains the blade with the special spanner
wrench (95C1-13). When installing a new knife, be sure
the name Eastman Machine Company is facing outward
and the knife seats on the knife gear. Install knife locknut
and secure setscrews. Secure guard in operating position.
Refer to page 13 for replacement knives.
CAUTION: Discard used sharp knives with care.
CAUTION
Do not use sewing machine oil or detergent oil. It is
entirely too light for cutting machine lubrication. For
best results use specially compounded Eastman Oil.
Do not oil Base Plate Rollers.
ITEM PART NO. DESCRIPTION QTY.
WARNING
Before performing any of the following procedures,
make sure that the attachment plug has been discon-
nected from power source.
1 See Page 11 Knives 1
2 95C1-13 Spanner Wrench 1
3 17C11 Knife Removal Pin 1
4 See Page 12 Emery Wheels 1
5 242C1 Eastman Oil 1
6 242C2 Eastman Gear Lubricant 1
7 242C2-2 Eastman Lubriko
Bearing Grease 1
8 See Page 15 Plastic Master Fluid 1
Maintenance Supplies
SILAC - Italy

4Form C-1519
LUBRICATION
DO NOT USEAN EXCESS AMOUNT OF OIL
Twice A Day
Oil emery wheel spindles at "C"
with specially compounded
Eastman Oil (242C1).
Once A Month
Grease Knife gear bearing. Re-
move bearing locknut with spanner
wrench and use a small amount of
Eastman Lubriko grease (242C2-2)
from tube.
Once A Day
Lubricate gears. Screw grease
cup down one-half turn. Rell
cup, as required with Eastman
Gear Lubricant special formula
(242C2).
LUBRICATION
With electrical cord disconnected, ll water can assembly at
"E" with diluted EASTMAN Concentrated PLASTIC MAS-
TER FLUID (242C3-0 or 242C3-3). Fluid must be diluted
with plain water before use. Add two ounces of uid with
one gallon of water. Shake or stir thoroughly.
NOTICE
TheEastman Machine Companydoes notwarrant this
Plastic Cutting Fluid and disclaims all liability for any
damage that may occur through its use.
SPONGE REPLACEMENT
With electrical cord disconnected and sight tube valve
"F" turned off, remove sponge holder cap from holder as
shown on page 17. Remove sponge. Install new sponge
and secure cap. Place sponge holder in working position
to continue operation.
SILAC - Italy

Form C-1519 5
TO ADJUST EMERY WHEELS
As the Emery Wheels wear away and become farther
apart, they must be adjusted. Emery Wheels must be
adjusted from
both sides to assure proper centering of the wheels over
the knife.
To adjust, loosen slotted head screws “A”. With ngers, turn
adjusting bushings “B” until Emery Wheels are as close
together as possible without touching and are centered
over the knife. Both wheels should grind at the same time
when pressed lightly against the knife and there should be
no more than 1/32 inch clearance between the two Emery
Wheels. Tighten slotted head screws “A”.
TO REPLACE EMERY WHEELS
With front of machine facing serviceman, guard rod in
down safe position, remove right hand grinding wheel and
arm by loosening setscrew “D” and sliding arm off shaft.
Removeslottedheadscrew“C”andreplacegrindingwheel
with spindle in right hand arm. Do not remove left hand
arm from machine. Remove slotted head screw “C” from
left hand arm and replace grinding wheel with spindle.
Re-assemble right hand arm to shaft and adjust wheels to
knife as described above.
MOTOR BRUSH REPLACEMENT
With electrical cord disconnected, unsnap Brush Cover
(53C11-165)frommotorandremovecover. RemoveBrush
Spring (34C1-62) from brush holder by pushing in, then
release. Gently pull brush wire to remove Brush (708C1-
18) and check for wear. If brush is less than
3/8"inlength,brushmustbereplaced. Disconnectterminal
from tab on motor.
Before inserting new brushes, use air hose or bellows with
proper eye protection and blow dust out of motor. When
inserting new brushes, brush wire must face slot in brush
holder. Connect brush terminal to tab on motor. Place
brush spring in guide with spring facing brush. With small
screwdriverslideclipdownandlockclipinplace,asshown.
Snap brush cover in place.
SILAC - Italy

6Form C-1519
Please specify model and serial number of ma-
chine when ordering parts.
Item numbers are for reference only.
Please specify PART NUMBERS when ordering
replacement parts.
NOTE:
Your Eastman RS2 Rubber Slitter Round Knife has been
carefully designed to provide many hours of trouble free
operation. The comprehensive exploded parts illustra-
tions have been carefully prepared to enable you to
easily order replacement parts, as required. Replace-
ment parts for this machine may be ordered thru your
nearest Eastman representative or directly from the
Eastman factory.
1 308C18-1 Screw, Socket Hd. Cap
1/4-20 x 1 1
2 302C12-5 Screw, Flat Hd. Cap
8-32 x 1/2 2
3 20C8-2 Screw 1
4 308C15-3 Screw, Socket Hd. Cap
10-32 x 3/8 2
5 308C15-2 Screw, Socket Hd. Cap
10-32 x 1/2 3
6 17C1-4 Pin, Taper 1
7 308C14-4 Screw, Socket Hd. Cap
10-24 x 3/4 3
ITEM PART NO. DESCRIPTION QTY.
Illustrated
Parts List
IMPORTANT:
Always specify machine model and
serial number when ordering parts for
faster more efcient service.
Index
EXPLODED PARTS ILLUSTRATIONS
The exploded part illustrations and part lists in this section
have been divided into major assemblies as follows:
Knife Replacement......................................... Page 3
Motor Assembly & Control Box....................... Page 8
Electrical Upgrade Kit..................................... Page 10
Standard Assembly......................................... Page 12
Sharpener Assembly ...................................... Page 14
Moistening Attachment & Guard Assembly .... Page 16
Baseplate Assembly....................................... Page 18
Service Record............................................... Page 23
Terminal Block, Attachment Plug.................... Page 24
OPTIONAL
Stationary Baseplate Assembly...................... Page 18
Strip Guage .................................................... Page 20
Motor Mounting Bracket ................................. Page 22
NOTE:
Three different abrasive Emery Wheel grits
(designed to provide you with a selection of
edges) may be ordered for this machine. See
page 12 of this manual for more information.
SILAC - Italy

Form C-1519 7
SILAC - Italy

8Form C-1519
Motor Assembly &
Control Box
Illustrated Parts List ITEM PART NO. DESCRIPTION QTY.
1 517C1-1215 Gear Motor, 110V 1
517C1-1280 Gear Motor, 220V
2 79C2-61 Label, Caution Sharp Blade 1
3 79C2-62 Label, Caution 1
4 300C7-1 Screw, Round Hd. Cap
4-36 x 1/8 1
5 254C1-2 Tie Mount 1
6 145C2-8 Cord #18-3 Wire 1
7 254C1 Cable Tie 1
8 21C14-19 Bushing, Strain Relief 1
9 199C1-11 Lug Ring 3
10 4C2-101 Nut, Wire Connector 2
11 308C20-116 Screw, Socket Hd. Cap
1/4-28 x 1 4
12 608C1-20 Intermediate Gear w/o Bearing
(Includes 87C1-31 Gear) 1
608C1-21 Intermediate Gear w/Bearing
(Includes 87C1-31 Gear) 1
13 12C11-18 A Washer, Spacer (.002 Thick) A/R
12C11-18 B Washer, Spacer (.003 Thick) A/R
12C11-18 C Washer, Spacer (.004 Thick) A/R
12C11-18 D Washer, Spacer (.005 Thick) A/R
12C11-18 E Washer, Spacer (.010 Thick) A/R
14 29C6-171 Adaptor, Motor 1
15 305C8-1 Screw, Binding Hd.
4-40 x 1/4 2
16 12C1-35 Washer 2
17 308C12-2 Screw, Socket Hd. Cap
8-32 x 1/2 2
18 783C1-10 Ground Wire Assembly 1
19 20C13-111 Screw, Grounding
10-32 x 3/8 1
20 104C1-6 Dial Indicator 1
21 830C1-56 Speed Control (110V) 1
22 4C2-106 Nut, Hex #4-40 2
23 8C13-87 Insulation 1
24 182C14-9 Control Box 1
25 306C80-201 Screw, Pan Hd.
8-18 x 3/8 4
26 580C1-124 Switch, 1 Phase 1
27 708C1-18 Motor Brush (Not Shown) 2
28 34C1-62 Brush Spring (Not Shown) 2
29 53C11-165 Brush Cover (Not Shown) 2
53C11-178 Brush Cover for Metal Top 2
A/R-As Required
Please specify model and serial number of ma-
chine when ordering parts.
Item numbers are for reference only.
Please specify PART NUMBERS when ordering
replacement parts.
NOTE:
SILAC - Italy

Form C-1519 9
WARNING: Terminal Block must be grounded. Attach
ground wire to ground terminal "E" on ter-
minal Block.
SILAC - Italy

10 Form C-1519
Electrical Upgrade Kit
820C4-5
Illustrated Parts List (After 1/20/2002)
ITEM PART NO. DESCRIPTION QTY.
1 104C1-6 Dial Indicator 1
2 580C1-124 Switch Dpst, Rocker
16A-250VAC 1
3 332-M3-16 Screw, Socket Flat Head
M3 x 0.5 x 16 4
4 182C14-14 Control Box 1
5 11-1316 Fuse, 2 Amp 2
6 4C2-82 Nut, Hex #6-32 2
7 11-1348 Fuse Holder, 2 Position 1
8 21C14-19 Bushing, Strain Relief 1
9 302C15-10 Screw, Flat Head
#10-32 x 1&3/8 2
10 313-86-6 Screw, Round Head
#6-32 x 3/8 2
11 305C15-2 Screw, Binding Head
#10-32 x 1/4 2
12 332-93-10 Screw, Socket Flat Head
#8-32 x 5/8 2
13 62C16-343 Mounting Bracket 1
14 308C12-1 Screw, Socket Head
#8-32 x 3/8 2
15 211-102 Nut, Elastic Hex #10-32 2
16 332-86-4 Screw, Socket Flat Head
#6-32 x 1/4 2
17 830C1-73 Speed Control, 110V 1
830C1-75 Speed Control, 220V
18 79C12-439 Nut Plate 1
19 4C2-110 Nut, Elastic Stop #8-32 2
20 236C1-137 Label, On/Off 1
Please specify model and serial number of ma-
chine when ordering parts.
Item numbers are for reference only.
Please specify PART NUMBERS when ordering
replacement parts.
NOTE:
P1
P3
L2L1
12 25
2411
BLUE
GRAY
BLACK
BLACK
WHITE
WHITE
BLACK
YELLOW/GREEN
GROUND
BLACK
WHITE
A+
F+
A-
F-
WHITE
BLACK
YELLOW/GREEN
GROUND
MOTOR
ON
OFF
SWITCH
580C1-124
POTENTIOMETER
5K
128C1-24
DRIVE BOARD
(110V) 830C1-73
(220V) 830C1-75
TERMINAL BLOCK
(220V) 508C1-101
(110V) 508C1-102
FUSE HOLDER 11-1348
FUSE 11-1316
NUT PLATE
517C1-1215
79C12-439
MIN IR CL MAX
P3
SET TRIMPOTS
REPLACE PLUG IN RESISTOR
WITH .1 OHM
P/N: 234C1-119
AS SHOWN
USE RIGHT ANGLE ON ALL OTHERS
USE STRAIGHT QUICK CONNECTS ON
lI AND L2 CONNECTIONS
SILAC - Italy

Form C-1519 11
1
2
3
4 7
5
6
19 18 17
16
15
4
8
9
Terminal Block
(Refer to back cover
for detailed parts list)
14 13
12
11
10
20
WARNING: Terminal Block must be grounded. Attach
ground wire to ground terminal "E" on ter-
minal Block.
SILAC - Italy

12 Form C-1519
ITEM PART NO. DESCRIPTION QTY.
Standard
Assembly
Illustrated Parts List
1 308C15-2 Screw, Socket Hd. Cap
10-32 x 1/2 3
2 308C15-3 Screw, Socket Hd. Cap
10-32 x 3/8 2
3 79C12-247 Bracket, Ref. Only 1
4 4C2-133 Insert Nut 10-32 5
5 72C4-20 Cup, Grease 1
6 88C1-184 Standard 1
7 29C6-173 Adaptor, Operating Handle 1
8 4C1-111 Locknut, Handle 1
9 531C1-53 Handle 1
10 25C4-157 Knife Guard 1
11 20C7-1 Screw, Thumb 1
12 12C9-8 Gear Spacing Washer 1
13 608C1-20 Intermediate Gear w/o Bearing
(Includes 87C1-31 Gear) 1
608C1-21 Intermediate Gear with Bearing
(Includes 87C1-31 Gear) 1
14 90C6-9 Internal Gear Bearing 1
15 20C4-26 Screw, Bearing Lock 1
16 4C1-103 Locknut, Internal Gear 1
17 53C4-52 Cover, Gear 1
18 302C7-2 Screw, Flat Hd. 4-36 x 1/4 4
19 309C12-3 Setscrew, 8-32 x 3/16 3
20 4C1-178 Locknut, Knife 1
21 * 7 1/2 Knife 1
22 4C1-113 Locknut, Knife 1
23 20C4-30 Screw, Lock 1
24 90C6-33 Bearing, Knife 1
25 87C2-25 Gear, Knife 1
26 521C1-26 Knife Gear Assembly 1
27 12C9-7 A Washer, Spacer (.002 THK) A/R
12C9-7 B Washer, Spacer (.003 THK) A/R
12C9-7 C Washer, Spacer (.004 THK) A/R
12C9-7 D Washer, Spacer (.005 THK) A/R
12C9-7 E Washer, Spacer (.010 THK) A/R
12C9-7 F Washer, Spacer (.020 THK) A/R
A/R-As Required
* See Table
Please specify model and serial number of ma-
chine when ordering parts.
Item numbers are for reference only.
Please specify PART NUMBERS when ordering
replacement parts.
NOTE:
SILAC - Italy

Form C-1519 13
For best results use only
GENUINE
EASTMAN Knives
The guarantee covering your RS2 Round Knife
is not valid if knives other than those
manufactured by Eastman are used.
7 1/2" DIAMETER
ROUND KNIFE SELECTION CHART
80C1-77 Carbon Steel
80C1-77G Carbon Steel, Grooved
80C1-77HS High Speed Steel
80C1-77HSG High Speed Steel, Grooved
Teon coated knives available.
Order by adding "T" to end of knife number.
WARNING
When cutting with the standard baseplate the knife
must be reversed. The name will face the outside.
When cutting with optional strip gauge the knife must
be reversed. The name will be on the inside.
See page15 for sharpener modication.
SILAC - Italy

14 Form C-1519
Sharpener
Assembly
Illustrated Parts List
ITEM PART NO. DESCRIPTION QTY.
1 57C2-22 Sharpener Lever 1
2 20C8-2 Screw 1
3 17C15-71 Cotter Pin, 1/16 x 1/2 2
4 77C1-34 Link, Sharp Contact 1
5 34C1-20 Spring, Tension 1
6 309C12-3 Setscrew, 8-32 x 3/16 2
7 46C3-13 Block, Sharpener Arm 1
8 11C10-19 Shaft, Sharpener 1
9 25C4-163 Knife Guard 2
10 540C1-51 LH Arm with Wheel L.H.
(120 Grit) 1
11 540C1-52 RH Arm with Wheel R.H.
(120 Grit) 1
12 309C12-1 Setscrew, 8-32 x 3/16 2
13 636C1-13 Sharpener Bracket 1
14 12C15-29 Washer, Flat 2
15 35C5-57 Arm, Sharpener 1
16 300C8-8 Screw, Round Hd.
4-40 x 5/16 4
17 300C10-5 Screw, Round Hd.
6-32 x 7/16 2
18 304C10-3 Screw, Truss Hd.
6-32 x 3/16 2
19 20C6-11 Screw, Bushing 1
20 541C1-9 Emery Wheel Ass’y(120 Grit) 2
541C1-13 Emery Wheel Ass’y(150 Grit) 2
541C1-21 Emery Wheel Ass’y(220 Grit) 2
21 92C1-12 Spindle 1
22 12C15-70 Washer 1
23 133C1-12 Emery Wheel (120 Grit) 2
133C1-14 Emery Wheel (150 Grit) 2
133C1-25 Emery Wheel (220 Grit) 2
24 12C1-28 Washer, Lock 1
25 20C13-20 Screw, Oval Hd. 8-32 x 5/16 1
26 300C12-3 Screw, 8-32 x 3/8 1
27 12C1-21 Lock Washer 1
28 35C5-65 Sharpener Arm 1
LH-Left Hand
RH-Right Hand
Please specify model and serial number of ma-
chine when ordering parts.
Item numbers are for reference only.
Please specify PART NUMBERS when ordering
replacement parts.
NOTE:
SILAC - Italy

Form C-1519 15
Warning
When interchanging Base Plate and Optional Strip
Gauge, the following changes must be performed:
1. With Standard Base Plate (page 18) the blade
isusedwiththeEASTMANnamefacingoutward.
The operator can then see the Eastman name.
When using the optional Strip Gauge, the blade
is used with the EASTMAN name facing in. The
operator will not see the EASTMAN name.
2. Sharpener modications:
When using Standard Base Plate the sharpener
assembly is assembled as shown.
When using the Optional Strip Gauge, the
Washers (item #14) must be placed together.
SILAC - Italy

16 Form C-1519
Moistening Attachment
& Guard Assembly
Illustrated Parts List
ITEM PART NO. DESCRIPTION QTY.
1 741C1-10 Water Can Assembly 1
2 53C11-69 Cover, Water Can 1
3 91C4-11 Rivet 1
4 720C1-32 Rod & Disc Top Assembly 1
5 12C15-61 Gasket 2
6 140C1-1 Body, Water Can 1
7 115C1-12 Disc, Bottom 1
8 12C15-63 Washer, Flat Rubber 1
9 12C15-60 Washer, Flat 1
10 4C1-152 Locknut 1
11 671C2-1 Valve, Sight w/Tube 1
12 73C7-41 Tube, Rubber 1
13 300C12-6 Screw, Round Hd.
8-32 x 1/2 2
14 62C16-116 Bracket, Water Can 1
15 4C2-93 Nut, Elastic Spline 1
16 300C12-6 Screw, Round Hd.
8-32 x 1/2 2
17 62C9-85 Bracket ,Guard 1
18 29C6-172 Adaptor, Guard 1
19 33C4-26 Holder Guard 1
20 20C4-38 Screw, Guard 1
21 17C15-123 Roll Pin, 3/32 x 5/16 1
22 20C5-2 Screw 1
23 65C2-18 Rod, Knife Guard 1
24 33C10-29 Sponge Holder 1
25 20C12-80 Screw, Sponge Holder 1
26 191C1-29 Sponge, 75X 1
27 86C7-17 Cap, Sponge Holder 1
28 73C7-31 Tube, Moist Device 1
Please specify model and serial number of ma-
chine when ordering parts.
Item numbers are for reference only.
Please specify PART NUMBERS when ordering
replacement parts.
NOTE:
SILAC - Italy

Form C-1519 17
GENUINE EASTMAN
Concentrated PLASTIC MASTER FLUID
242C3-0 - 1/2 Pint
242C3-1 - 1 Gallon
GENUINE EASTMAN
Concentrated PLASTIC MASTER FLUID
for Rubber Products
242C3-2 - 1/2 Pint
242C3-3 - 1 Gallon
SILAC - Italy

18 Form C-1519
Stationary Baseplate Assembly
(Optional)
Illustrated Parts List
Baseplate Assembly
Illustrated Parts List
ITEM PART NO. DESCRIPTION QTY.
ITEM PART NO. DESCRIPTION QTY.
ITEM PART NO. DESCRIPTION QTY.
1 79C12-247 Bracket 1
2 62C16-226 Bracket for Standard 1
3 302C15-4 Screw, Flat Hd. 10-32 x 5/8 4
4 505C3-230 Plate Base, Complete 1
5 79C5-264 Plate, Throat 1
6 300C12-2 Screw, Round Hd.
8-32 x 1/4 2
7 300C12-5 Screw, Round Hd.
8-32 x 7/16 4
8 300C12-3 Screw, Round Hd.
8-32 x 3/4 5
9 622C1-4 Roller Plate (Front) 2
10 41C2-7 Roller Plate 10
11 12C8-1 Washer, Plate Roller 2
12 61C1-5 Shell, Plate Roller 1
13 11C2-13 Shaft, Plate Roller 1
14 98C4-11 Clip, Roller Shaft 4
15 302C10-1 Screw, Flat Hd. 6-32 x 3/16 8
16 59C1-151 Plate, Flat 75X 1
17 619C1-8 Roller Plate (Rear) 1
18 12C8-1 Washer, Plate Roller 4
19 41C2-7 Roller Plate 20
20 61C1-5 Shell, Plate Roller 2
21 11C2-14 Shaft, Plate Roller 1
22 20C5-12 Screw 4
23 17C6 Pin, Hinge 2
24 60C1-14 Wing Plate 1
1 59C3-143 Stationary Baseplate 1
2 79C5-264 Plate Throat 2
3 79C12-247 Bracket 1
4 762C16-226 Bracket for Standard 1
5 302C15-4 Screw, Flat Hd. 10-32 x 5/8 4
6 332-93-8 Screw, Socket Flat Head
8-32 x 1/2 11
SILAC - Italy

Form C-1519 19
1
2
3 4
5
6
SILAC - Italy

20 Form C-1519
Strip Gauge (optional)
505C2-98A - 18"
505C2-98B - 24"
Illustrated Parts List
ITEM PART NO. DESCRIPTION QTY.ITEM PART NO. DESCRIPTION QTY. 16 17C15-126 Roll Pin 1/8 x 1/2 1
17 15C13-60 Stud 1
18 171C1-22 Gauge Lock 1
19 90C6-63 Bearing, Linear 1
20 15C13-63 Stud, 3" 1
21 11C12-121A Bearing Shaft, 18" 1
11C12-121B Bearing Shaft, 24"
22 11C12-122A Shaft, Support, 18" 1
11C12-122B Shaft, Support, 24"
23 189C1-24 Post, Gauge Support 2
24 308C21-4 Screw, Socket Hd.
5/16-18 x 1 2
25 4C1-111 Locknut, Handle 1
26 531C1-53 Handle, Operating 1
27 59C1-171A Base Plate, 18" 1
59C1-171B Base Plate, 24"
28 320C23-216 Screw, Flat Hd.
3/8-16 x 1 2
29 320C15-1 Screw, Flat Hd. 10-32 x 3/8 8
30 622C1-4 Roller Plate 4
31 12C8-1 Washer, Plate Roller 2
32 61C1-5 Shell Plate Roller 1
33 41C2-7 Roller Plate 10
34 11C2-13 Shaft, Plate Roller 1
35 320C15-1 Screw, Flat Hd. 10-32 x 3/8 4
36 62C16-305 Bracket, Standard 1
1 13C2-11 Knob, Hand 2
2 300C10-4 Screw, Round Hd.
6-32 x 3/8 2
3 25C4-178 Lower Side Guard 1
4 4C2-134 Nut, Flange 3/8-16 2
5 55C4-147 Spacer 1
6 12C15-46 Washer, Flat 5/16 2
7 25C4-179 Lower Front Guard 1
8 79C12-403 Plate, Standard to Bracket 1
9 308C15-1 Screw, Socket Hd.
10-32 x 5/8 2
10 59C1-172 Guide Plate 1
11 236C1-111 Label, Instruction 1
12 728C1-5 Stabilizer Assembly 2
13 305C8-2 Screw, Binding Hd.
4-40 x 3/8 4
14 62C16-306 Lock Bracket 1
15 308C15-5 Screw, Socket Hd.
10-32 x 3/4 2
Please specify model and serial number of ma-
chine when ordering parts.
Item numbers are for reference only.
Please specify PART NUMBERS when ordering
replacement parts.
NOTE:
SILAC - Italy