Eastwood 30640 User manual

3.5 GALLON BENCHTOP
PARTS WASHER
INSTRUCTIONS
Item #30640

2Eastwood Technical Assistance: 800.544.5118 >> [e-mail] To order parts and supplies: 800.345.1178 >> eastwood.com 3
ASSEMBLY
• Thread the Flexible Metal “Gooseneck” Fluid
Outlet Tube onto the Pump Outlet Fitting (Fig A).
• Place the Parts Cleaning Tray over the ledges
on the walls of the tub. Make sure the Nozzle
of the Flexible Metal “Gooseneck” Fluid Outlet
Tube is shaped to be facing in and downward
toward the center of the Tub (Fig B).
• Fill unit with suitable, water-based degreasing
solution sufficiently to cover the entire Pump
(approx. 1.5 gallons) (Fig C).
Important Notes:
- Follow degreasing solution mixing, usage
and safety label instructions carefully
before using.
- Be sure the cleaning solution level fully
covers the Pump or it will not function
properly.
• Plug power cord into an approved, grounded
and GFI equipped 120 Volt AC, 60hz. outlet.
• Turn Power Switch to the “On” position.
The Parts Washer is now ready for use.
OPERATION
• Place parts to be cleaned on the Parts Tray.
• Allow cleaning solution to flow completely over
the part surface, wetting it completely. Allow
time for solution to soften any grease and
debris then use a suitable parts cleaning
brush to remove stubborn deposits.
• Let excess solution drain from parts then
remove from washer and rinse in warm water.
• When done, turn pump to the off position,
close lid and unplug unit.
Your Eastwood 3.5 Gallon Benchtop Parts Washer is specifically designed with heavy-duty
components and a quality powder-coated finish to provide years of trouble-free service. It features
a flexible, positionable metal “Gooseneck” fluid outlet tube with nozzle for added convenience.
SAFETY INFORMATION
SPECIFICATIONS
• 120 Volt AC, 60hz current requirement
• Maximum pump capacity @ outlet: 1 gallon per minute
• 3.5 gallon tub capacity, 1.5 gallon operating capacity
INCLUDES
(1) 3.5 Gallon capacity tub (1.5 gallon actual operating capacity)
(1) Parts tray
(1) Flexible, positionable metal “Gooseneck” fluid outlet tube with nozzle
READ INSTRUCTIONS!
Thoroughly read and understand manual before using this Parts Washer Tool.
Save for future reference.
WARNINGS!
• NEVER use solvent based or flammable cleaning agents in this parts washer.
The recirculating pump is designed to operate with water based cleaning agents
only. Solvents will quickly destroy the pump and could present a fire hazard.
• DO NOT use paint or powder dissolving solutions that would remove the
powdercoated finish of the Tub and components.
• NEVER let parts washer run while unattended. Clogging of the filter and resulting
overheating of the pump motor can occur.
• ALWAYS plug into an approved, grounded and GFI equipped 120 Volt AC,
60hz. outlet.
• For indoor use only.
• ALWAYS wear chemical resistant gloves and adequate eye protection.
Fig. A
Fig. A
Fig. B
Fig. B
Fig. C
Fig. C

© Copyright 2014 Easthill Group, Inc. Instruction part #30640Q Rev. 10/6/14
If you have any questions about the use of this product, please contact
The Eastwood Technical Assistance Service Department: 800.544.5118 >> email: [e-mail]
PDF version of this manual is available online >> eastwood.com/30640manual
The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA
US and Canada: 800.345.1178 Outside US: 610.718.8335
Fax: [phone] eastwood.com
MAINTENANCE
• Unplug unit and inspect the pump intake grill
after every hour of cleaning (Fig D).
Clean more often if removing excessively heavy
deposits of grease and grit. Important Note:
Failure to clean pump intake will result in
diminished fluid flow, cleaning effectiveness
and eventual pump motor failure.
• If it becomes apparent that the pump intake
grill requires cleaning more often, it is likely that
the cleaning solution needs to be replaced and an accumulation of sediment from the Tub bottom
needs to be removed.
- Drain and pour drain cleaning solution into suitable containers and dispose of properly.
TROUBLESHOOTING
• If Fluid stops flowing or flows sporadically, the Pump may not be fully submersed. The Pump
must be fully under the fluid surface level to work properly (Fig C).
• If pump intake cleaning does not restore pump performance, an accumulation of dirt and grit
may be present in the Flexible Metal “Gooseneck” Fluid Outlet Tube.
- Unplug unit and remove Flexible Metal “Gooseneck” Fluid Outlet Tube and check for
obstructions lodged in tube and remove.
Fig. D
Fig. D
Pump
Pump
Intake Grill
Intake Grill