i-MO Öko 2000 User manual

IMO GmbH Gässlesweg 6 D-75334 Strauben ardt Tel.: [phone] Fax: 604 36 www.imo-ag.com [e-mail]
GmbH
Öko 2000
User Guide
Öko 2000
1

IMO GmbH Gässlesweg 6 D-75334 Strauben ardt Tel.: [phone] Fax: 604 36 www.imo-ag.com [e-mail]
2
GmbH
Contents page
1. Safety instructions 4
2. Schedule of connection 5
2.1 Schedule of connection of effluent hose 6
3. Starting up 7
3.1 Connecting up the circuit board washing machine 7
3.2 Installation of the filter unit 7
3.3 Removing the air from the deioniser cartridge 7
3.4 Cleaining agent dosage 8
3.5 Operating control front panel 9
3.6 Cleaning 10
1. Preparation 10
2. Cleaning 10
3. Removing the washed load 10
4. Operating summary 11
4.1 Main menue 11
4.2 Start program 11
4.3 Program new / alter 12
4.4 Program delete 14
4.5 Setup 14
4.5.1 Date / time setting 14
4.5.2 Change languare 14
4.5.3 Monitor Sprayarm on/off 15
4.5.4 Detergent 15
4.5.4.1 List of detergent setting / alter 15
4.5.4.2 Assign detergents to dosing pump 16
4.5.4.3 Suck detergent 16
4.5.4.4 Alter pumpfactor 16
4.5.5 Alter code 16
4.6 Network settings 17
5. Program flow 18
5.1 Step of cleaning 18
5.2 Step of rinsing 19
5.3 Step of drying 20
5.4 End of program 20
5.5 Example of program 21
5.6 Indications and manifestations 22
5.6.1 oaming 22
5.6.2 Exchange of filter unit 22
5.6.3 Exchange of the air filter 22
5.6.4 Cleaning of the dirt trap 22
5.6.5 Cleaning of the screen insert 22
5.6.6 Exchange of the sprayarms 22
5.6.7 Exchange of the dosing hoses 23
5.6.8 Version with white dosing head 23
5.6.9 Version with black dosing head and transparent lid 24

IMO GmbH Gässlesweg 6 D-75334 Strauben ardt Tel.: [phone] Fax: 604 36 www.imo-ag.com [e-mail]
3
GmbH
Continuation Contents page
6. Interfaces / network connection 25
7. Error messages 26
8. Function of the connector plugs 30
9. Technical informations 31

Dear Customer,
we are glad because of your interest in our products.
Thank you for the confidence you have shown us.
Please attend technical safety instructions on this page, before startup
of your new cleaning machine for circuit boards Öko 2000.
Now we wish you success at cleaning of your products.
If you have questions, you can get in contact with us anytime.
IMO GmbH
IMO GmbH Gässlesweg 6 D-75334 Strauben ardt Tel.: [phone] Fax: 604 36 www.imo-ag.com [e-mail]
4
GmbH
1. Safety Instructions
The washing machine ÖKO 2000 must only be connected to a supply protected
by a fuse rated not more than 16A! Please see for the power supply voltage
at the type label on the machine.
The installation of the machine should be arranged from employees, who are familiar
with installation of such or similar machines. Our technicians will like to help you.
Please only use cleanser, which you have bought at our company.
Our cleansers are coordinated especially at the cleaning requirements of that
cleaning machine for circuit boards. If you anyway should want to use an other cleanser,
please obtain an O.K. from our technicians. If you use external cleanser and you didn’t
get O.K. from us, you will loose guarantee for your machine, because such cleanser
can destroy the machine.
Please make sure, if your laundry is suitable for such cleaning processes. We assume no
liability for damages because of process, material and temperature compability on cleaned
circuit boards and components.
You can’t clean glas-tube fuses! Those components please fit after cleaning process.
Please regulary check the boarder of the bottom metal filter for traces of rust. These may
be caused by pieces of iron and may lead to contact corrosion on the stainless steel.
If you do not dry after cleaning process, you have got to start every day after work a separat
drying process. So your can avoid damages of corrosion (rust) at the drying turbine.
The opened door to charge only with max. 25 kg (with extended grate and laundry)
Don’t use as work disk or seating. Don’t stand on it, there is danger of tilting!
To avoid water damage, the cleaning machine can be put into operation only in connection
with the external solenoid valve.

IMO GmbH Gässlesweg 6 D-75334 Strauben ard t Tel.: [phone] Fax: 604 36 www.imo-ag.com [e-mail] m
5
GmbH
2.Schedule of connection Öko 2000
NE water deionizer with conductivity measurement
Back side
ÖKO2000
Filter candle
Filter housing
Waste water
Hose end in no
case lower than
the level
alternatively
detergent container
Observe local wastewater discharge
regulations
Network
Wastewater hose
Mount the filter cartridge at the height
of the upper edge of the machine.
Air filter
Dosing unit
Connections
Water inlet
live - with
230V 50Hz when filling
Water desalination unit
Fresh water
inlet
Solenoid valve directly on
permanently installed water
connection / Observe
installation direction
T-piece brass
E.C. Measuring cell LM-LED
1804.0000.39

IMO GmbH Gässlesweg 6 D-75334 Strauben ardt Tel.: [phone] Fax: 604 36 www.imo-ag.com [e-mail]
6
GmbH
End of waste water hose
min. 300 mm
End of waste water hose
Alternative
min. 300 mm
2.1 Schedule of connection of effluent hose
or to avoid an uncontrolled drain of water out of the cleaning system, the open, and thereby
aerated end of waste water hose has to be mounted after the waste water filter at least
30 cm above the installation surface of the ÖKO 2000.
If the hose ends lower, it may be possible that because of the vacuum lifting effect, the
water drains out of the machine.

IMO GmbH Gässlesweg 6 D-75334 Strauben ardt Tel.: [phone] Fax: 604 36 www.imo-ag.com [e-mail]
7
3. Starting up
3.1 Connecting up the circuit board washing machine
The circuit board washing machine ÖKO2000 must be set up in a horizontal position.
Water supply: Connect up according to the connection diagram page 5.
The water pressure should be at least 2 bar and not more
than 8 bar.
The machine must not be connected to a no-pressure
water heater.
Drain: Connect up according to the connection diagram page 5.
The local waste water regulations have to be observed!
Elect. connection: The washing machine must only be connected to a
220V - 230V AC supply though a correctly installed mains socket.
3.2 Installation of the filter unit
The supplied filter unit has to be mounted on the wall at or above the top of the machine
(see connection diagram).
3.3 Removing the air from the deioniser cartridge
Please notice, that by starting up of a new deioniser cartridge the air inside removes by itself.
This can cause error messages, which you have to disregard.
The program interrupts and is to start again. This procedure is to retry till the cleaning progam
runs through (normal case 5-10 times).
or a faster deaeration a temporary operation with reverse flow direction is possible.
Therefore, the connections „inlet“ and „outlet“ have to be changed.
After some filling operations of the system, the connections have to be mounted at the
right positions again.
The remaining air can be removed at the vent valve in the cover.
GmbH
ormal operation
fresh water to Öko 2000

3.4 Cleaning agent dosage
Liquid components
Powder:
IMO GmbH Gässlesweg 6 D-75334 Strauben ardt Tel.: [phone] Fax: 604 36 www.imo-ag.com [e-mail]
8
GmbH
Liquid components are dosed automatically during cleaning via the built-in dosing pumps,
as programmed, automatically during the cleaning process.
(Activator AT can also be added manually to the washroom before the cleaning process).
Dispense powdered cleaning agent, as shown, onto the inside of the open front flap before
starting the cleaning process, or when prompted by the equipment.

3.5 Operating Controll Front Panel
IMO GmbH Gässlesweg 6 D-75334 Strauben ardt Tel.: [phone] Fax: 604 36 www.imo-ag.com [e-mail]
9
GmbH
Following washing programs are setted ex work, but can be altered if required:
Program 1:
Cleaner: Component A+ and Mix 3
Program 2:
or cleaning pcb-boards with only colophony flux and drying afterwards.
Cleaner: Mix 3, ca. 40gr
Program 3:
Cleaner: Mix 3
Program 4:
Only drying
Pointer upward / increase value
Confirm / continue
Pointer downward / decrease value
Back / interruptionOn / off switch
3.5.1 Removing the upper support grid
For large items to be washed, the upper support grate with spray arm can simply be removed.
Then the entire interior height is available for cleaning.
To remove the upper support grate, pull it out as far as it will go, then lift slightly and
upwards at an angle. It is inserted in the opposite direction.
The water supply to the upper spray arm is automatically closed by a ball
valve during removal. This means that the complete spraying capacity is available at
the lower spray arm.
For cleaning printed circuit boards in general, also suitable for removing
of "no clean" flux residues.
With subsequent drying.
For cleaning lightly soiled objects, e.g. degreasing
and dust removal with subsequent drying.

3.6 Cleaning
IMO GmbH Gässlesweg 6 D-75334 Strauben ardt Tel.: [phone] Fax: 604 36 www.imo-ag.com [e-mail]
10
GmbH
- Open the front door
- Dosage of the cleaning agent (see item 3.4)
- Place the frames carrying the circuit boards into the washing space
1. Preparation
- Close the front door
- Switch on ÖKO 2000
- Select “start program” and confirm
- Use pointer up / pointer down to select the required program
- Confirm the required program with “ENTER”
- Machine begins to run; the program sections are indicate on the display
- inish message after the end of the cleaning program
2.Cleaning
- Switch off the machine
- Open the front door
- Remove the wash frames with the circuit boards from the wash space
Warning: washed load is hot!
- Close the front door
3.Removing the washed load
Please note:
The machine works only when the front door is closed properly. To open the front
door immediately interrupts the program sequence. This is indicated by flashing on
display. During the heating-up phase the display shows the elapsed time of
cleaning or rinsing as follows: ‘--’ . After the temperature has reached its debit, the
programed time starts. The elapsed time is shown on the display.