Eastwood 54441 User manual

12 TON FLOOR SHOP PRESS
INSTRUCTIONS
Item #54441

2Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
The EASTWOOD 12 TON FLOOR SHOP PRESS is excellent for many mechanical procedures requiring a strong linear pressing force for disassembly
or assembly operations. A generous 7.1” Ram Stroke and adjustable 3” to 36” vertical working range can easily accommodate many ball joint, u-joint,
bearing, bushing and gear pressing projects. The convenient Foot Pedal feature provides a choice of hands-free, foot actuated operation or the standard,
hand operation pump function.
CONTENTS
BOX 1
(2) Main Frame Sides - [A]
(2) Upper Frame Beams - [B]
(2) Base Rails – [C]
(1) Lower Cross Member – [D]
(4) Angle Braces – [E]
(1) Foot Pedal – [F]
(1) Linkage Arm - [G]
(2) Table Support Pins – [H]
(1) Table – [J]
(1) Pump Handle – [K]
BOX 2
(1) Hydraulic Pump Unit - [L]
(1) Upper Yoke Plate – [M] (thinner)
(1) Lower Yoke Plate – [N] (thicker with locating pins)
(1) Ram w/Lock Collar – [P]
(1) Force Gauge – [Q]
(1) Nylon Seal – [R]
(4) Table Support Pin Clips – [S]
(1) Foot Pedal Spring – [T]
(1) Foot Pedal Pivot Shaft Ass’y – [U]
(2) Spring Eyelet Ass’y – [V]
(2) Linkage Clevis Pins – [W]
(2) Cotter Pins – [X]
(2) Arbor Plates – [Y]
SPECIFICATIONS
Hydraulic Pump Capacity: 12 Tons (24,000 lbs.), [10,886 kg] maximum
Hydraulic Ram Stroke: 7.1” [175 mm]
Overall Vertical Working Range: 3” to 36” [77-917mm]
Arbor Depth: 4.33”. [110mm]
Horizontal Working Capacity: 20.25”. [515mm]
HARDWARE: BOX 2
(2) M10 x 1.50 x 145 mm Shoulder Bolts
(4) M10 x 1.50 x 16 mm Bolts
(8) M10 x 1.50 x 30 mm Bolts
(4) M10 x 1.50 x 35 mm Bolts
(14) M10 Nuts
(18) M10 Washers
(14) M10 Lock Washers
(8) M12 x 1.75 x 30 mm Bolts
(8) M12 Nuts
(8) M12 Washers
(8) M12 Lock washers
A
B
C
D
E
F
G
H
JK
L
M
BOX 2BOX 2
BOX 1BOX 1
B
N
R
P
Q
ST
U
X W V
Y

To order parts and supplies: 800.343.9353 >> eastwood.com 3
READ INSTRUCTIONS
• Thoroughly read and understand this manual before using.
• Save for future reference.
PINCH HAZARD!
• This tool has hydraulically actuated components that generate greatly amplified crushing and bending forces which can quickly cause
severe injury! Keep fingers and hands away from moving parts when operating.
INJURY HAZARD!
• While in use, objects under pressure in the Eastwood 12 Ton Floor Shop Press can suddenly slip out of position, releasing a great deal of
stored energy and force causing serious injury or death and property damage. Work from the Pump side of the Frame at all times.
Do not allow others near the tool while in operation.
INJURY HAZARD!
• The Eastwood 12 Ton Floor Shop Press was specifically designed to be operated by one person only. Never have one person operate the
lever while one handles the Ram or Spreader, or serious injury could occur.
• Injury or property damage could occur from being struck by ejected workpiece fragments. Before beginning work, be sure the
surrounding work area is clear of persons or objects to avoid injury or property damage.
• Excessive resistance while operating could indicate excessive side loads or component binding. To avoid injury and or severe tool
damage, stop work immediately and inspect tool components and extensions for any deflection or bending.
• The Eastwood 12 Ton Floor Shop Press consists of heavy metal components which can cause serious injuries if allowed to drop.
Avoid pinching hands while handling parts during assembly.
• Obtaining the assistance of a helper during assembly is recommended.
• The Eastwood 12 Ton Floor Shop Press is intended for use as a linear pushing and compression tool.
DO NOT use as a jack, lifting, or support device.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to personal injury.
SAFETY INFORMATION
The following explanations are displayed in this manual, on the labeling, and on all other information provided with this product:

4Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
ASSEMBLY
• Attach the Upper Frame Beams [B] to the Main Frame Sides [A] with 8 sets of
M12 x 1.75 x 30 mm Bolts, Nuts and Washers (FIG 1).
• Join the Main Frame Sides [A], the Base Rails [C] and the flanges of the Lower
Cross Member [D] together with four M10 x 1.50 x 35 mm Bolts, Nuts and Lock
Washers (FIG 2).
NOTE: Do Not tighten hardware until all pieces are assembled to allow for
alignment.
• Add the four Angle Braces [E] between the Main Frame Sides [A] and the
Base Rails [C] with M10 x 1.50 x 30 mm Bolts, Nuts, Washers and Lock
Washers (FIG 3).
• Stand the Assembled Frame upright carefully mount the Hydraulic Pump Unit [L]
onto the outside face of the right Main Frame Side [A] with four M10 x 1.50 x 16
mm Bolts, Washers and Lock washers (FIG 4).
• Center and set the Upper Yoke Plate [M] on the top of the assembled Frame
Beams [B] with the Lower Yoke Plate [N] under the Frame Beams. Secure with
(2) M10 x 1.50 x 145 mm Shoulder Bolts, Washers and Nuts (FIG 5).
NOTE: Do Not overtighten bolts and distort the thinner Upper Yoke Plate.
• Unthread and remove the pre-installed Lock Collar from the Ram [P] and place
it aside for later re-installation (FIG 6).
FIG. 1FIG. 1
FIG. 2FIG. 2
FIG. 3FIG. 3 FIG. 4FIG. 4
FIG. 5FIG. 5 FIG. 6FIG. 6

To order parts and supplies: 800.343.9353 >> eastwood.com 5
FIG. 7FIG. 7
FIG. 8FIG. 8
FIG. 9FIG. 9 FIG. 10FIG. 10
FIG . 11FIG . 11 FIG. 12FIG. 12
• Insert the Ram [P] with the hose connection end facing upward, through the
center holes of the Yoke Plates [M] & [N]. Thread the previously removed Lock
Collar onto the threads of the Ram [P] (FIG 7).
• Slip the Nylon Seal [R] over the threaded fitting of the Force Gauge [Q] then
install it with the Gauge facing forward (FIG 8).
• Remove the protective plastic cap from the female fitting on the side of the Ram
[P] and thread the male, Hydraulic Pump hose fitting into it (FIG 9).
• Remove the Outer Locknuts and one washer from the Foot Pedal Pivot Shaft
Ass’y [U] and set them aside.
• Insert the longer threaded end of the Foot Pedal Pivot Shaft [U] (with the inner
nut and washer in place) into the corresponding hole in the face of the right Main
Frame Side [A] (FIG 10).
• Using the previously removed Locknut and Washer, secure the Pivot Shaft tightly
in place.
• With the Pedal facing upward, slide the sleeved end of the Foot Pedal [F] over
the Pivot Shaft and secure with the previously removed Locknut and Washer
(FIG 11).
NOTE: Do Not overtighten and cause binding.
• Set one end of the Linkage Arm [G] into the Clevis of the Hydraulic Pump Ass’y
Arm, slip a Linkage Clevis Pin [W] through the holes and secure with a Cotter Pin
[X] (FIG 12).
• Place the opposite end of the Linkage Arm [G] into the clevis tabs of the Foot
Pedal [F], slip a Linkage Clevis Pin [W] through the holes and secure with a
Cotter Pin [X] (FIG 12).

6Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
• Remove the outer nut and washer from the Spring Eyelet Ass’y [V] and set
them aside.
• Insert the threaded end of the Spring Eyelet [V] into the corresponding hole in the
face of the right Main Frame Side [A] and secure with the previously removed nut
and washer (FIG 13).
• Hook the ends of the Foot Pedal Spring [T] into the Spring Eyelet and the tab on
the upper edge of the Foot Pedal arm [F] (FIG 13).
• Insert the (2) Table Support Pins [H] through the selected pair of 8 available
height setting holes in the Main Frame side members [A]. Secure by snapping
the Spring Clips [S] into the annular grooves (FIG 14).
• Feeding it from above at an angle, install the Table [J] between the Frame side
members and resting on the Table Support Pins [H] (FIG 15). Retain the Pins
using the Table Support Pin Clips [S].
IF USING HAND CONTROL PUMP HANDLE:
• Slide the Pump Handle [K] into the Pumping Lever of the Pump [L] (FIG 15).
• The Arbor Plates [Y] are placed as needed on top of the Table [J] to support
the workpiece.
FIG. 13FIG. 13
FIG. 14FIG. 14
FIG. 15FIG. 15

To order parts and supplies: 800.343.9353 >> eastwood.com 7
SET-UP AND OPERATION
INSTALLATION LOCATION
FIG. 16FIG. 16
The Eastwood 12 Ton Floor Shop Press is designed to be used in
a Vertical position only with the Main Frame securely placed on a
clean, level and stable surface. DO NOT attempt to use in a horizontal
or any other position.
The Eastwood 12 Ton Floor Shop Press MUST be installed on a solid
and level surface for proper operation and safety.
INJURY HAZARD!
While in use, objects under pressure in the Eastwood 12 Ton Floor Shop Press can suddenly slip out of position, releasing a great deal
of stored up energy and force causing serious injury or death and property damage. Work from the Pump side of the Frame at all times.
Do not allow others near the tool while in operation.
INJURY HAZARD!
Use caution and do not allow side loading of the Ram piston if attempting offset loads.
Before beginning use, carefully plan out the positioning of the Support Table, Ram and Arbor Plates and analyze the expected movement
of the workpiece to minimize the danger of sudden movement or slippage.
OPERATION
• The Ram [P] and Yoke Plate [M] & [N] assembly can be moved off center if necessary to apply an offset force is possible but not recommended due to
the unequal stresses that can be transmitted through the frame. To do so, loosen the bolts, slide it into position then re-tighten bolts.
• Check that the Release Valve (Knob located at the Lower side of the Hydraulic Pump) (FIG 16) is closed. (Rotate in a Clockwise direction).
• Begin slowly operating Pump Handle while constantly observing the workpiece for expected movement and any signs of sudden slippage.
• When planned work is completed, carefully and slowly rotate the Release Valve (Rotate in a Counter-Clockwise direction) to release pressure.

© Copyright 2021 Eastwood Automotive Group LLC 4/21 Instruction item #54441Q Rev 1
If you have any questions about the use of this product, please contact
The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: [e-mail]
PDF version of this manual is available at eastwood.com
The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA 800.343.9353 eastwood.com
MAINTENANCE
CHECK/ADD HYDRAULIC FLUID TO PUMP
• Check that the Release Valve (FIG 16), (NOTE: Knob located at the Lower Front side of the Hydraulic Pump) is closed (rotate in a Clockwise direction).
• Remove Oil Fill Screw at top of Pump.
NOTE: Do Not lose Seal Ring.
• The fluid level should be visible at the bottom of the threads. If required, add a high-quality hydraulic fluid.
• Check that the Seal Ring is in place on the Fill Screw/Breather and thread the Fill Screw into the Pump securely.
STORAGE
• Keep in a clean, dry area free of corrosive moisture with Ram in the retracted position. Covering with thick plastic is recommended.
TROUBLESHOOTING
PROBLEM CAUSE CORRECTION
Ram Stops
Before Full
Work Stroke is
Completed
Low fluid level in Reservoir Retract Ram fully and check fluid level. Add a high quality, hydraulic oil
as needed.
Offset forces causing binding of
components Retract Ram and check thoroughly for any offset forces acting on components.
Pushing Capability of the Ram has
been exceeded Retract Ram and discontinue use.