Eastwood TIG 200 DC WELDER Quick reference guide

TIG 200 DC WELDER
ASSEMBLY & OPERATING INSTRucTIONS
Part #14100

2
SPEcIFIcATIONS
STATEMENT OFLIMITED WARRANTY
The Eastwood Company (hereinafter “Eastwood”) warrants to the end user (purchaser) of all new welding and cutting equipment that it will be free of defects in workmanship
and material. This warranty is void if the equipment has been subjected to improper installation, improper care or abnormal operations.
WARRANTY PERIOD:
All warranty periods begin on the date of purchase from Eastwood. Warranty Periods are listed below, along with the products covered during those warranty periods:
3 Year Warranty on Material, Workmanship, and Defects:
• Eastwood TIG 200 DC Welder
Itemsnotcoveredunderthiswarranty:Collets,colletbodies,electrodes,nozzles,andgroundclampandcable.
All other components are covered by the warranty and will be repaired or replaced at the discretion of Eastwood.
2Years:
• All Welding Helmets.
CONDITIONS OF WARRANTY TO OBTAIN WARRANTY COVERAGE:
Final determination of warranty on welding and cutting equipment will be made by Eastwood.
WARRANTY REPAIR:
If Eastwood confirms the existence of a defect covered under this warranty plan, Eastwood will determine whether repair or replacement is the most suitable option
to rectify the defect. At Eastwood’s request, the purchaser must return, to Eastwood, any products claimed defective under Eastwood’s warranty.
FREIGHT COSTS:
The purchaser is responsible for shipment to and from Eastwood.
WARRANTY LIMITATIONS:
EASTWOOD WILL NOT ACCEPT RESPONSIBILITY OR LIABILITY FOR REPAIRS UNLESS MADE BY EASTWOOD. EASTWOOD’S LIABILITY UNDER THIS WARRANTY SHALL NOT EXCEED
THE COST OF CORRECTING THE DEFECT OF THE EASTWOOD PRODUCT. EASTWOOD WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES (SUCH AS LOSS OF
BUSINESS, ETC.) CAUSED BY THE DEFECT OR THE TIME INVOLVED TO CORRECT THE DEFECT. THIS WRITTEN WARRANTY IS THE ONLY EXPRESS WARRANTY PROVIDED BY
EASTWOOD WITH RESPECT TO ITS PRODUCTS. WARRANTIES IMPLIED BY LAW SUCH AS THE WARRANTY OF MERCHANTABILITY ARE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY FOR THE EQUIPMENT INVOLVED. THIS WARRANTY GIVES THE PURCHASER SPECIFIC LEGAL RIGHTS.
THE PURCHASER MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Output
Amperage
Range
10-200 A
DC
Maximum
Output No Load
Voltage
50-80 V DC
Input
Voltage
120 VAC
50-60 Hz
/220 VAC
50-60 Hz
Rated
Duty
Cycle
60%
@ 150 A
Pre
Gas
Flow
0.5 Sec
Post
Gas
Flow
5 Sec
Weight
18 Lbs.
Overall
Dimensions
16.9”
(430 mm) x
7.3”
(185 mm) x
12”
(306 mm)
TIG Welding is the most controllable, efficient and versatile method of welding many metals including steel, stainless steel and more.
Your Eastwood TIG200 DC Welder with High-Frequency Inverter Technology is capable of welding thin or heavy gauge steel with
precision and ease. The voltage self-sensing circuitry automatically detects a power source range of 110 to 240 volts and delivers from
10 up to 200 Amps DC. The included foot pedal provides the operator with the precise amperage control required when welding. A high
frequency start feature guarantees an instant arc strike with no tungsten contamination.
READ AND UNDERSTAND ALL INSTRUCTIONS AND PRECAUTIONS BEFORE PROCEEDING.
This unit emits a powerful high voltage and extreme heat which can cause severe burns, dismemberment, electrical shock and death.
Eastwood shall not be held liable for consequences due to deliberate or unintentional misuse of this product.

3
SAFETY INFORMATION
FLAMMABILITY HAZARD
• Before beginning, make sure the work surface is cleaned of any oils, coatings or other materials which can ignite
and or emit dangerous fumes or vapors.
•Molten metal can be ejected away from the welding area with significant force and speed. Make sure the entire
work area is clear from flammable or easily damaged materials or objects.
HIGH VOLTAGE DANGER
•The unit contains no user serviceable parts!
•Contact with the torch when the button is depressed will result in a serious shock and severe burns!
• This device also produces High-Frequency, Radio-Frequency Emissions which can damage sensitive electronic
equipment in the area. Keep all cell-phones, cameras, watches and other electronic equipment at least 6’ away
from the Power Unit and Torch.
•IMPORTANT NOTE: If you have a medical condition or pacemaker check with your doctor before using as the
RF emissions may cause interference.
ELECTRICAL SAFETY DO’S
•Make sure you, your work area, and your equipment are dry. Avoid welding in high humidity and with
excessive perspiration.
• If you are using an extension cord, make sure it is a grounded cord in sound condition with no damage or frays,
and of the correct wire gauge. (220 Volt @ 10 gauge minimum / 110 Volts @ 12 gauge minimum).
•Keep all cords as far away from the welder unit as possible to avoid any possibility of arcing to the internal
transformer. This includes the power cord, torch feed cord and ground clamp cord.
•Remove change, watches or other metallic objects from your clothing.
•Sweep up all metal grinding particles and dirt from the floor before beginning welding.
• Use a non-metallic chair.
•To further isolate yourself from ground, position yourself over a rubber mat while welding.
• Ensure that proper sized circuit breakers and wiring are in place prior to use: 20 Amp for 110 Volt operation
and 30 Amp for 240 Volt operation. Single Phase Only.
•Turn welder off when not in use.
DuTY cYcLE
The rated Duty cycle refers to the amount of welding that can be done within an amount of time. The Eastwood TIG200 DC
has a duty cycle of 60% at 150 Amps. It is easiest to look at your welding time in blocks of 10 Minutes and the Duty Cycle
being a percentage of that 10 Minutes. If welding at 150 Amps with a 60% Duty Cycle, within a 10 Minute block of time you
can weld for 6 Minutes with 4 Minutes of cooling for the welder. To increase the duty cycle you can turn down the
Amperage Output control. Going above 150 Amps will yield a lower duty cycle.

4
ELECTRICAL SAFETY DON’TS
•Never bypass the ground plug. Grounding is necessary for proper operation of the unit and reduces shock hazard.
•Do not touch the torch tip until after the activation switch is off and the unit is UNPLUGGED.
• Do not use the unit if any component should become damaged or show signs of excessive wear.
• Never handle the torch and the feed cable, power cord or welder cabinet at the same time. Fatal shock can occur.
• Avoid welding in extreme humidity or while heavily perspired.
• Do not wrap welding cables around your body
UV AND IR RAY DANGERS
The ARC welding process produces Ultra Violet (UV) and Infrared (IR) Rays that can injure your eyes and skin. Do not
look at the welding arc without a minimum #10 eye shade and skin protection.
•Always weld with a helmet that covers your entire face and neck.
•Always use a helmet with a lens of Shade 10 or darker.
•Always cover all bare skin with protective clothing. Flame retardant clothing is always the best.
• Never allow anyone around the area you are welding without proper protection.
HOT MATERIALS DANGERS
Materials being welded are very hot and can cause severe burns if handled improperly.
• Do not touch welded materials with your bare hands, use great caution when lifting a piece with gloves.
It is best to allow the part to cool completely before handling.
•Do not touch the electrode, electrode holder, or ground clamp with bare hands until it has cooled.
HAZARDOUS FUMES AND GASES DANGER
•Keep your head out of the fumes.
• Use ventilation or an exhaust system to keep the fumes and gasses from your general and breathing area.
• Do not weld painted or plated parts as they can release toxic gases or fumes.

5
REquIRED ITEMS
Before you begin using the Eastwood TIG200 DC, make sure you have the following:
• A properly grounded 110-120 VAC 50/60 Hz. 20 Amp Circuit or a 220-240 VAC 50/60 Hz. 30-50 Amp Circuit.
•NOTE: Unit must be grounded to work properly and safely!
•A clean, safe, well-lit, dry and well-ventilated work area.
• A non-ammable, long sleeve shirt or jacket (Eastwood #12762).
• Heavy-Duty Welding Gloves (#12590)
• An Auto Darkening Welding Mask to provide eye protection during welding operations.
Note: MUST be a #10 lens or darker.
•A compressed gas cylinder containing 100% Argon (must be used when TIG welding and is available
at any welding supply facility).
• Dedicated stainless steel wire welding brushes for each material to be welded.
•A dedicated fine grit synthetic stone grinding wheel or a Tungsten Sharpener.
uNPAcKING
Remove all items from the box. Compare with list below to make sure unit is complete.
• Eastwood TIG200 DC Welder with NEMA50-P Plug
•Shielding Gas Regulator
• Shielding Gas Hose
• Ground Cable with Clamp (10’)
• #17 TIG Torch (14’)
•Foot Pedal for Amperage Control
• 110-120 VAC to 220-240 VAC Adaptor Plug
•Instruction Manual
• Hand Held Shield
•Hammer/Brush
•#7 Cup (7/16”)
•#6 Cup (3/8”)
•#5 Cup (5/16”)
• Long Back Cap
• Short Back Cap
• 3/32” Collet Body
• 3/32” Collet
•1/16” Collet
• 2.0mm Collet
• 2.0mm Red (Thoriated Tungsten)

6
cOMPONENTS AND cONTROLS
1. Power Switch – The Power Switch is located at the left of the front panel (Fig A).
2. Amperage (Front Panel) – Set the Output Amperage Knob marked “A” (Fig. A) located at right of the front panel to an
appropriate setting based on the thickness and type of the metal being welded. (Refer to Data Chart for actual settings).
3. Amperage (Foot Pedal) Output – Same operation as the panel control but is used while the foot pedal is in use (Fig B).
4. Gas Flow – The included regulator limits the shielding gas flow from the bottle and also displays how much gas is left
in the bottle. The Gas Flow Indicator Gauge is located on the left side and is generally set between 12 to 20 SCFH.
(Refer to Data Chart for actual settings). This is explained in
further detail in the Preparing to Weld section of this manual.
The gauge on the right indicates the pressure left in the tank.
5. Foot Pedal/Panel Control – The Foot Pedal/Panel Control selection
switch is located in the center of the front panel and when set in the
‘Foot Pedal’ position, the Foot Pedal control is activated. When set to
the ‘Panel Control’ position, the Torch Trigger is activated. (Fig. A)
6. Torch Switch – The switch on the torch (Fig. C) controls starting and
stopping the arc. When using the torch switch the Amperage is set on
the adjustment knob on the front panel of the welder.
7. Foot Pedal – The foot pedal is for starting and stopping the arc as well
as controlling the Amperage during the weld. When using the foot
pedal the Amperage is set by the adjustment knob on the side of the
foot pedal. (Fig. B)
DATA cHART (ALSO LOcATED ON TOP OF wELDER)
Material Material
Thickness Polarity Amperage Tungsten Color Tungsten Diameter Filler Metal Filler Metal Diameter Torch Cup Size Gas Flow Rate (scfh)
Steel 1/16" DC 45-80 Orange, Red, White 1/16" ER70S-2 1/16" 1/4-3/8" 12
Steel 3/32" DC 70-110 Orange, Red, White 1/16" ER70S-2 1/16" 1/4-3/8" 12
Steel 1/8" DC 75-125 Orange, Red, White 1/16" ER70S-2 3/32" 1/4-3/8" 12
Steel 3/16" DC 110-200 Orange, Red, White 3/32" ER70S-2 1/8" 1/4-3/8" 14
Stainless Steel 1/16" DC 50-90 Orange, Red, White 1/16" ER308/308L 1/16" 1/4-3/8" 12
Stainless Steel 3/32" DC 80-120 Orange, Red, White 1/16" ER308/308L 1/16" 1/4-3/8" 12
Stainless Steel 1/8" DC 85-140 Orange, Red, White 1/16" ER308/308L 3/32" 1/4-3/8" 12
Stainless Steel 3/16" DC 125-200 Orange, Red, White 3/32" ER308/308L 1/8" 1/4-3/8" 14
FIG. A
FIG. B FIG. C

7
SETuP
SHIELDING GAS CONNECTION
A Shielding Gas Bottle is not included with your Eastwood TIG200 DC but is
necessary while TIG welding. A Shielding Gas Bottle can be bought at most local
Welding Supply Stores. Eastwood recommends the use of 100% Argon shielding
gas when TIG welding Steel and Stainless Steel.
1. Place the Eastwood TIG200 DC in its dedicated area or on a welding cart.
2. Secure your Shielding Gas Bottle to a stationary object or mount to your
welding cart if it is equipped to hold one so that the cylinder cannot fall over.
3. Remove the cap from the Shielding Gas Bottle.
4. Insert the large brass male tting on the Shielding Gas Regulator into the
female tting on the Shielding Gas Bottle. (Fig. D) NOTE: Do not use White
Teflon Tape on this connection as it is a tapered thread and does not
require it, if you have a leak check for burrs or dirt in the threads. If the
leak persists, use gas type sealing tape.
5. Tighten the fitting with a wrench till snug, do not over tighten.
6. Connect either end of the Gas Line included with your
Eastwood TIG200 DC to the tting on the regulator and tighten
with a wrench until snug.
7. Connect the other end of the gas line to the fitting on the rear of the
Eastwood TIG200 DC and tighten with a wrench until snug. (Fig. E)
TORCH CONNECTION
1. Install the plastic connection cover onto the brass torch tting on
the torch cable.
2. Connect the female brass fitting on the torch cable to the male
brass fitting on the welder. (Fig. F)
3. Use a wrench and tighten until snug. DO NOT OVERTIGHTEN.
4. Connect the metal plug to the Torch Switch Connection as shown in FIG F.
NOTE: Omit this step if you will be using the foot pedal for Amperage control
GROUND CABLE CONNECTION
1. Locate the Ground Cable and Clamp.
2. The Ground Cable connection is located at the far right of the front panel as
shown in FIG F. With the Key on the connector in the 12 O’clock position,
insert the connector and turn 180° clockwise to lock the connector in.
FOOT PEDAL CONNECTION
1. If you are going to be using the switch on the torch to start the welding arc, omit this step.
2. Connect the metal plug on the Foot Pedal to the Switch Connection as shown in FIG F.
FIG. D
FIG. E
FIG. F
Ground
Cable
Torch
Switch/Foot
Pedal
Gas Flow
Through Pow-
er Cable
✓
✓
✓

8
PREPARING TO wELD
TORCH DISASSEMBLY/ASSEMBLY
DISASSEMBLY:
1. Make sure the welder is turned off and unplugged.
2. Remove the back cap from the torch.
3. If there is a tungsten installed in the torch pull
it out of the front of the torch
4. Slide the collet out of the torch.
5. Unscrew and remove the gas nozzle.
6. Unscrew and remove the collet body.
ASSEMBLY:
1. Select a collet body that matches your tungsten diameter size and thread it back into the front of the torch.
2. Select a collet that matches your tungsten diameter size. Insert the tungsten into the collet and put the collet and tungsten back
into the torch.
3. The cup size should be changed according to shielding gas requirements for the material being welded. This size can be referenced
on the suggested settings chart. Select the correct gas nozzle and thread it onto the collet body.
4. Reinstall the back cap to lock the tungsten in place. Always make sure the tungsten protrudes 1/8” to 1/4” beyond the gas nozzle.
SHARPENING THE TUNGSTEN
To avoid contamination of the Tungsten and ultimately the weld, it is imperative to have a dedicated grinding wheel used for
Tungsten grinding only. A fine grit standard 6” synthetic stone grinding wheel on a bench top grinder is sufficient or specifically
designed Tungsten Grinders are available.
1. Shut off the welder.
2. Make sure the Tungsten and Torch are sufficiently cooled for handling then
loosen and remove the Back Cap then the Collet (Fig G) and remove the
Tungsten from the FRONT of the Torch only. (Removing from the rear will
damage the Collet).
3. If the tungsten is used and the end is contaminated, use pliers or a suitable
tool to grip the tungsten above the contaminated section and snap off the end
of the Tungsten.
4. Holding the Tungsten tangent to the surface of the grinding wheel, rotate the
tungsten while exerting light pressure until a suitable point is formed (Fig H).
5. The ideal tip will have the length of the conical portion of the sharpened area at
2-1/2 times the Tungsten rod diameter (Fig I).
6. Replace the Tungsten in the Collet with the tip extending 1/8”-1/4”
beyond the Gas Cup, then re-tighten the Back Cap.
FIG. H
FIG. I
Gas Nozzle
✑✒✓✔
Collet Body
✑✒✓✔
Collet
✑✒✓✔
Back Cap
✑✒✓✔
✑✒✓✔
Tungsten
FIG. G

SETTINGS SELEcTION
With the materials selected of which you will be welding you can begin to set up the welder for the specific material.
1. Foot Pedal / Panel Control – Determine whether you will be using the switch on the torch or the foot pedal for arc
starting and stopping and put the selector switch in the appropriate position. Note that some connections changes
will be necessary also when switching the control type. These connection changes are covered in the Set-Up section
of this manual.
2. Amperage – If welding using the switch on the torch to control the arc, Set the Output Amperage Knob marked “A”
(Fig. A) located at upper left of the top panel to an appropriate setting based on the thickness and type of the metal
being welded. (Refer to Data Chart for actual settings). If welding using the foot pedal to control the arc, it uses the
same operation as the panel control but is adjusted on the side of the foot pedal rather than the front panel. (Fig B).
3. Power Switch – Once all of the settings have been selected and the torch assembled and ready to use, the
welder can be plugged in and turned on.
4. Shielding Gas Flow – Set the Gas Flow Rate to the appropriate value with the Knob located at the left side
of the regulator.
SHIELDING GAS FLOw ADjuSTMENT
After connecting your Shielding Gas Regulator, the gas ow rate needs to be adjusted so that the proper amount of
Shielding Gas is owing over your weld. If there is too little gas ow there will be porosity in your welds as well as
excessive spatter, if there is too much gas ow you will be wasting gas and may affect the weld quality. The included
regulator has 2 gauges on it; the gauge on the left is your ow rate while the gauge on your right is your tank pressure.
1. Open your Shielding Gas tank valve all the way.
2. Adjust the knob on the regulator to ~20 CFH.
3. Turn on the welder and trigger the torch switch which will start the gas flow.
4. As you trigger the torch switch you will notice that as the gas flow starts the needle on the gauge drops to a
steady reading. The reading while flowing is the value you want to read.
5. The gas ow should be set to 12-20 CFH while owing. The CFH (Cubic Feet per Hour) scale is the inside scale
in red on your ow gauge. 20 CFH is the most typical ow rate but it may need to be adjusted in some cases
depending if there is a slight breeze or some other instance where additional shielding gas is required to
prevent porosity in the weld.
6. When finished welding remember to close the gas valve on the bottle.
9

10
wELDING
IMPORTANT NOTE:
These instructions are intended only to provide the user with some familiarity of
the Eastwood TIG200 DC. TIG welding is a highly complex procedure with many
variables. If you have no experience with TIG welding; it is extremely important
to seek the advice of someone experienced in TIG welding for instruction, enroll
in a local technical school welding course or study a comprehensive how-to DVD
and obtain a good quality reference book on TIG welding as there is a moderate
learning curve necessary before achieving prociency in TIG Welding. Before
attempting to use this unit on an actual project or object of value, practice on a
similar material as there are many variables present and settings required when
TIG welding different metals such as steel and stainless steel. It is also strongly
recommended that the user adhere to the American Welding Society guidelines,
codes and applications prior to producing welds where safety is affected.
1. Turn the Power Switch to the on position.
2. Slowly open the gas cylinder valve. NOTE: Always open valve fully to
avoid shielding gas leakage.
3. Depress gun trigger switch or foot pedal and adjust the ow regulator.
(Refer to Data Chart for actual settings).
4. Grounding is very important, place the Ground Cable Clamp on a clean, bare
area of your work piece as close to the welding area as possible to minimize
the chance of shock. Scrape, wire brush, file or grind a bare area to achieve
a good ground to assure safety.
5. Use a dedicated stainless steel brush or ap-disc to clean the areas to be
welded. Do not use the brush or ap-disc for any other purpose.
6. Making sure all your safety gear is in place (Welding Mask, Welding Gloves,
non-flammable long sleeve apparel) and the area is completely free of
flammable material.
7. Although it is a matter of developing a personal style, a good starting point for best results is achieved by holding the tip at a 75°
angle backward and approx. 20° to the right of the weld. Hold the Filler Metal Rod at a 90° angle to the Tungsten Tip (Fig. J).
Never allow the Tungsten Tip to touch the welding surface or material rod. Doing so will quickly destroy the tip and contaminate
the weld. If this happens, remove the Tungsten and regrind the tip. It is best to hold the tungsten tip 1/8” from the surface.
8. With your Welding Shield and all safety gear in place, depress the foot pedal or trigger and practice “Forming A Puddle” with the
Tungsten Tip. Once you become familiar with this step. Practice the “Dip and Pull” technique with the Filler Metal Rod and Torch.
“Dip and Pull” is the practice of forming a puddle, moving the torch while maintaining the puddle and adding ller rod metal to the
puddle by “dipping and pulling” as you go; being careful not to allow the tungsten to contact the puddle or rod.
9. Keep in mind that you MUST let the shielding gas ow over the weld after releasing the trigger or pedal. Failure to do so will
allow the welded area to oxidize compromising the weld integrity.
10. Constantly be aware that TIG welding quickly generates heat in the work piece and torch. Severe burns can quickly occur by
contacting hot metal pieces.
11. When done, shut off the Power Switch and close the Shielding Gas Tank valve completely.
FIG. J
FIG. K
FIG. L
75°
90°

11
11
TROuBLESHOOTING
TROUBLESHOOTING
Problem
Cause
Fix
Arcistriggeredbutwillnotstart
IncompleteCircuit
CheckGroundconnection.Makesure
thatthegroundisonafreshlycleaned
surfaceandclosetotheweldingarea.Itis
suggestedtoweldtowardstheground
connection.
IncorrectTungsten
Consultchartforpropertungstenforthe
basemetalbeingwelded.Inmostcases
Thoriatedwillbeusedforallsteels.
Noshieldinggas
Makesuretheshieldinggascylinderis
turnedallthewayopenandsetatthe
correctflowrate.
Arcwandersanditis
hardtoconcentrateheat
inaspecificarea
Poorlyprepped
tungsten
Followguidelinesforpreppingtungsten.
PoorGasFlow
Adjusttheflowrateoftheshieldinggas
(refertosettingschart).Checkforloose
fittingswheregascouldbeleaking.
Contaminated
Tungsten
Removetungstenfromtorchandbreak
offcontaminatedsectionandresharpen.
Incorrectarclength
Makesurethetungstenisheld1/8to1/4
inchofftheworkpiece.
Incompletecircuit
CheckGroundconnection.Makesure
thatthegroundisonafreshlycleaned
surfaceandclosetotheweldingarea.It
issuggestedtoweldtowardstheground
connection.
Contaminatedbase
metal
Cleanbasemetalmakingsuretoremove
anyoil,debris,coatings,ormoisture.If
basemetalisaluminummakesureallof
theoxideisremovedusingeithera
dedicatedstainlessbrushorflapwheel.
Porosityinweldbead
PoorGasFlow
Adjusttheflowrateoftheshieldinggas
(refertosettingschart).Checkforloose
fittingswheregascouldbeleaking.
Contaminatedfiller
metal
Cleanfillermetalmakingsuretoremove
anyoil,debris,ormoisture.
Contaminatedbase
metal
Cleanbasemetalmakingsuretoremove
anyoil,debris,coatings,ormoisture.
PoorShielding
Makesuretobeinanareawithnowind
andwithanyfansturnedoff.Windor
fanswillblowtheshieldinggasaway
fromtheweldcausingporosity.
IncorrectTungsten
StickOut
Adjustthetungstensothat1/8to¼inch
isstickingoutofthecollet.

12
TROuBLESHOOTING






#"(!"(
)"'("
!#*()"'("&#!(#&"&
##"(!"('(#""&'&$"/
#"(!"( &
( 
 " &!( !"')&(#&!#*
",# .&'.#&!#'()&/
#"(!"('
( 
 "'!( !"')&(#&!#*
",# .&'.#("'.#&!#'()&/
'!( '# &# '( !')&
(#&!#*",! ' /




##&' #+
)'(( #+&(#(' "'
1&&(#'(("'&(2/#& ##'
(("'+&'#)  "/
&#"-)"'(" "&'()"'("!(&/&(#
&(#&$&#$&'-"/
"#&&( "
' " ,)'544;&#"+" "/



 #+# (
# ('(("'(## #+#&
!(& 0("''/"&''"
"&&"&(#"+ &/



 #"((#)"'("
+('( 
$()"'("507(#506"&#!(
'!( /()"'("#!'"#"((
&#""&'&$"
!!( ,/



 "#&&($#'(#""
" (+"( &!( "
((#&!)'( ''("84&'
#(&+'( &!( + 
$&!()& ,! (" ##)'"
$##&+ $$&"/





"')"( "
$((#&#"('!( + 
($#'( #+' "' #+'(#
$&#(("## (!( "()"'("/
#("#) &
(& 
))&&"(+($ "!#&
 &("#+ /(!, '#
" (#'($(#"')&"#
&(&+ #&!/




##!)("
!(& 
)(" #+!#&(!
(+"$'''/
'( '
'#&"(##!)
(
&('!( 1#"') (+ "
#'#&&%)&!"('2
"#&&( && '$$&#$&( &+&(,$"
!(&#&(#"("+ /




13
TROuBLESHOOTING







 
!



!



!
 
 "

!




















AccESSORIES
TIG WELDING SUPPLIES:
•#12253 – ER70S-2 TIG Wire 1/16-36”
•#12254 – ER70S-2 TIG Wire 3/32-36”
•#2463 – 308L Stainless TIG Wire 1/16-36”
•#12464 – 308L Stainless TIG Wire 3/32-36”
•#12871 – Thoriated Tungsten (Red) 1/16-7” 2pc
•#12872 – Thoriated Tungsten (Red) 3/32-7” 2pc
REPLACEMENT ITEMS:
•#13483 – TIG200 Collet Body (1.6mm; 1/16”)
•#13484 – TIG200 Collet Body (2.4mm; 3/32”)
•#12822 – TIG200 Collet (1.6mm; 1/16”)
•#12824 – TIG200 Collet (2.4mm; 3/32”)
•#12825 – TIG200 Long Back Cap
•#12819 – TIG200 Gas Nozzle (9.8mm; 3/8”)
•#12821 – TIG200 Gas Nozzle (11.2mm; 1/2”)
•#13953 – TIG Accessory Kit
OTHER WELDING ACCESSORIES:
•#11947 – Flap Disc 60 Grit 4.5” Diameter 7/8” Hole
•#12590 – Welding Gloves Large
•#12589 – Welding Gloves Medium
•#13203 – Auto Darkening Welding Helmet
•#13212 – Large View Auto Darken Welding Helmet
•#19079S – Stainless Steel Brush
•#12762 –L, XL, XXL Welding Jacket
•#21524 – TIG Welding Basics DVD by Ron Covell
•#11616 – TIG200 Welding Cart
•#14106 – Welding Table