Eaton Green Motion DC 22 Installation guide

©2023 Eaton. All rights reserved..1
Green Motion DC 22
Installer training

©2023 Eaton. All rights reserved..
Disclaimer
Green Motion DC 22
 procedures
that may be in place at your company and is not a substitute for the Green
Motion DC 22 installation manual and user manual.
None of the materials herein may be copied, reproduced, distributed,
downloaded, displayed or transmitted in any form or by any means without
the prior written permission of Eaton.
2

©2023 Eaton. All rights reserved..

www.eaton.com/greenmotiondc22
For more information, contact us at 
Resources and Documentation
Green Motion DC 22
3

©2023 Eaton. All rights reserved..
Green Motion DC 22
Product overview
▪DC charging for everyone
▪Fast charging speed, high efficiency
▪Future-proof charging station
▪Compact charging station
▪Quiet DC charging experience suited to all types
of vehicles
4

©2023 Eaton. All rights reserved..5
Technical specifications
POWER INPUT
Input voltage AC
3 x 400 V 50 Hz, 3
-phase
Nominal input current AC
3 x 32 A
(22 kW), 3-phase
POWER OUTPUT
Nominal output power
22 kW
Output voltage for the DC range
50 V
- 500 V
Output type
-
CCS Type 2 (default)
-
CCS Type 2 and CHAdeMO (optional)
OPTIONS
Floor
-mounted
Mounted on a floor
-mount pedestal
Network interface
Ethernet cable or 4G (optional)
Access control
RFID, Scan & Charge
WARRANTY
Warranty
2 years

©2023 Eaton. All rights reserved..
Package contents
Green Motion DC 22 includes the following parts:
Green Motion DC 22 EV charging station
Quick start guide
Safety guidelines
EV cables(s), depending on customer configuration:
CCS plug and cable
CCS and CHAdeMO plugs and cables
Plug holder(s) for cable(s),
Screws, cable glands and cable cap,
Wall-mount gaskets (four pieces)
NOTE: Optional floor-mount pedestal is sold separately
6

©2023 Eaton. All rights reserved..7
Types of cables and connectors
The Green Motion DC 22 EV charger offers two types of
cables with connectors:
1. CCS Type 2
2. CHAdeMO (optional)

©2023 Eaton. All rights reserved..8
Rating plate
Information that can be found on the rating plate (1):
A. Manufacturer
B. Model
C. Power ratings
D. Certification marks
E. Warnings
F. Serial number

©2023 Eaton. All rights reserved..9
Open/close housing
1. Unscrew the screws located on the top-right
and the bottom-right side of the charging
station using the T20 screwdriver.
2. Open the front door.

©2023 Eaton. All rights reserved..
Green Motion DC 22
Mounting and installation
▪Environmental and mounting conditions
▪Site design
▪Mounting on the wall
▪Mounting on the floor-mount pedestal (optional)
10

©2023 Eaton. All rights reserved..11
Environmental and mounting conditions
Relative humidity below 95%.
Temperature range from -25 °C to +45 °C
Altitude not exceeding 2000 m above sea level
Mounting height of 1600 mm above ground level
At least 300 mm of free space on both sides for unobstructed
air circulation
An easy access to controls and connections

©2023 Eaton. All rights reserved..12
Environmental conditions
Do not mount the unit above or below flammable building
materials.
Do not install the unit in areas where highly flammable
substances are present.
Do not install the unit in areas subject to explosion hazard.




©2023 Eaton. All rights reserved..
Site design
Site design 1 Site design 2
1 2 3
Charging Station Charging Station Charging Station
13
1
2
Charging Station
Charging Station
600 mm (min.)

©2023 Eaton. All rights reserved..14

Mounting on the wall
Make sure the wall can support the weight of the unit,
providing enough load-bearing capacity to withstand
additional stress caused by cable tensioning:
The charging station 53 kg
The CCS cable 4 kg
The CHAdeMO cable 6 kg
Note that the appropriate types of plastic plugs and screws
must be selected by a professional installer, based on the
following considerations:
The installation site
The type of the wall

©2023 Eaton. All rights reserved..15
1. Green Motion DC 22 EV charger
2. Floor
3. Plug holders
Mounting on the wall
(total overview)

©2023 Eaton. All rights reserved..16
Fixing the unit onto the wall
1. Place four gaskets on the back of
the charging station:
2. Install the four M6 x 50 stainless
steel screws into the wall, leaving
them to protrude 10 mm from the
surface.
16

©2023 Eaton. All rights reserved..17
Fixing the unit onto the wall
3. Mount the unit onto the protruding
screws, temporarily using them as
holders.
4. Fasten the screws tightly and
securely, thus fixing the unit against
the wall
17
1
2
3

©2023 Eaton. All rights reserved..
Fixing the CCS plug holder to the wall
1. Keep 300 mm free space between
the EV charger and the plug holder.
2. Mount the metal sheet cable
support on the wall at a height
between 1000 mm and 1100 mm
from the ground.
3. Ensure that the polarizing keys
are on the top side of the plug
holder.
4. Fix the CCS plug holder with
screws to the cable support.
18
Polarizing
keys
Screws

©2023 Eaton. All rights reserved..19
Fixing the CHAdeMO plug holder to the wall
1. Keep 300 mm free space between
the EV charger and the plug holder.
2. Mount the metal sheet cable
support on the wall at a height
between 1000 mm and 1100 mm
from the ground.
3. Ensure that the polarizing keys
are on the top side of the plug
holder.
4. Fix the CHAdeMO plug holder with
screws to the cable support.
Polarizing
keys
Screws

©2023 Eaton. All rights reserved..20
Mounting on a floor-mount pedestal (optional)
It is possible to install the Green Motion DC 22 EV
charger on a dedicated floor-mount pedestal. The
following slides will show the correct way of installing
the EV charger on the pedestal.
Please note that the appropriate types of
stainless-steel rods, nuts, and flat washers must
be selected by the installer, considering the
conditions at the installation site.
Make sure to keep at least 300 mm of free space
on both sides of the pedestal!
Make sure no objects prevent the use of the unit
by obstructing the access to the charging plug
and cables!
