Eaton 600 A 35 kV Class Insulated Standoff Bushing User manual

General
Eaton's Cooper Power™ series 600 A, 25 kV Class
PUSH-OP™ adapter cap is a factory assembled
loadbreak reducing tap plug and bushing extender
with a stainless steel shroud and tin-plated copper
probe. It meets all the requirements of IEEE
Std 386™-2006 standard, Separable Connector
Systems.
The device is used to cap a 600 A PUSH-OP
type bushing interface with the 200 A loadbreak
interface, allowing for live testing and visible
grounding.
It is 200 A three-phase switching and three-
phase fault close rated. When used with Eaton's
Cooper Power series 200A insulated protective
cap, M.O.V.E. arrester or a grounding elbow, the
PUSH-OP adapter cap provides a fully shielded,
submersible unit.
Installation
The PUSH-OP adapter cap is installed on a
de-energized 600 A special PUSH-OP bushing
interface using a clampstick tool. Refer to Service
Information S600-19-1, 600 A, 15, 25, and 35 kV
Class PUSH-OP Bushing Adapter Cap Installation
Instructions for installation instructions.
Production tests
Tests are conducted in accordance with IEEE Std
386™-2006 standard.
• AC 60 Hz 1 Minute Withstand
• 40 kV
• Minimum Corona Voltage Level
• 19 kV
Tests are conducted in accordance with Eaton
requirements.
• Physical Inspection
• Periodic Dissection
• Periodic Fluoroscopic Analysis
600 A 25 kV class PUSH-OP™
insulated adapter cap
Deadbreak Connectors
Catalog Data
CA650103EN Effective September 2016 Supersedes 600-39 January 1990
COOPER POWER
SERIES

Figure 1. Cutaway illustration shows design detail and dimensions. Catalog PDBA625 shown.
ote:N Dimensions given are for reference only.
13.3 (337.8)
8.7 (220.9)
7.2 (182.9)
Table 1. Voltage Ratings and Characteristics
Description kV
Standard Voltage Class 25
Maximum Rating Phase-to-Phase (LRTP 200 A interface only) 26.3
Maximum Rating Phase-to-Ground 15.2
AC 60 Hz 1 Minute Withstand 40
DC 15 Minute Withstand 78
BIL and Full Wave Crest 125
Minimum Corona Voltage Level 19
Voltage ratings and characteristics are in accordance with IEEE Std 386™-2006 standard.
Table 2. Current Ratings and Characteristics
Description Amperes
200 A Interface*
Continuous
Switching
200 A rms
10 operations at 200 A rms at 26.3 kV
Fault Closure 10,000 A rms symmetrical at 26.3 kV after 10 switching
operations for 0.17 s
Short Time 10,000 A rms symmetrical for 0.17 s
3,500 A rms symmetrical for 3.0 s
Current ratings and characteristics are in accordance with IEEE Std 386™-2006 standard.
600 A
PUSH-OP
BUSHING
LOCATING
PINS
HOTSTICK
PULLING EYE
CATCH ASSEMBLY
Prevents unit from falling off
of PUSH-OP mating apparatus
upon removal.
COPPER PROBE
Field Replaceable Tin-Plated
Copper Probe ensures
reliable electrical connection.
GROUNDING LEAD
48 inch #14 Stranded Plated
Copper Ground Lead ensures
deadfront construction and
avoids low energy discharge
from the molded semi-
conducting shields.
200 A
LOADBREAK
REDUCING TAP
PLUG
2
Catalog Data CA650103EN
Effective September 2016
600 A 25 kV class PUSH-OP insulated adapter cap
www.eaton.com/cooperpowerseries
* If available system fault current exceeds 10 kA, current-limiting fusing must be used upstream,
otherwise fault close and short time ratings of the 200 A interface will be exceeded.

Ordering information
To order a 25 kV Class PUSH-OP Insulated Adapter Cap Kit, refer to
Table 3.
Each kit contains:
• Assembled Adapter Cap
• Shipping Cap (not for energized operation)
• Silicone Lubricant
• Installation Instruction Sheet
Table 4. Replacement Parts
Description Catalog Number
Reducing Tap Plug (Includes STUD-T) LRTP625
Probe 2638198B01B
Catch Assembly 2638191B01
Shipping Cap (for 200 A interface) 2637269B04
Table 3. Insulated Adapter Cap Kits
Description Catalog Number
Adapter Cap PDBA625
Adapter Cap with 200 A Insulated Protective Cap PDBA625C
3
Catalog Data CA650103EN
Effective September 2016
600 A 25 kV class PUSH-OP insulated adapter cap
www.eaton.com/cooperpowerseries

Eaton is a registered trademark.
All trademarks are property
of their respective owners.
600 A 25 kV class PUSH-OP insulated adapter capCatalog Data CA650103EN
Effective September 2016
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eaton’s Power Systems Division
2300 Badger Drive
Waukesha, WI 53188
United States
Eaton.com/cooperpowerseries
© 2016 Eaton
All Rights Reserved
Printed in USA
Publication No. CA650103EN
For Eaton's Cooper Power series PUSH-OP
connector product information call
1-877-277-4636 or visit:
www.eaton.com/cooperpowerseries.