Eaton CDAU-01/04 User manual

Smart Dimming Actuator
CDAU-01/04, CDAU-01/04-I, CDAU-01/04-E
OFF
868.3 MHz
IP20
R, L, C, LED, ESL
M
1.5 mm2
10 mm
Local input
A
B
Program
Mode
Actuator Type Load
CDAU-01/04 250 W
CDAU-01/04-I Local input 250 W
CDAU-01/04-E EMS, kWh 250 W
Neutral wire needed!
Nuldraad benodigd!
Nøytralleder nødvendig
Neutralleiter erforderlich!
Nulovy vodičzapotřebí!
+55°C*
-5°C
-25°C
+70°C
Technical Data / Technische gegevens / Tekniske data /
Technische Daten / Technická data
Power supply 230 VAC +10% -15%, 50 Hz
Load 0 - 250 W (0 - 250 VA)
LED, ESL: 0 - 100 W*
* Depending on the lamp type.
Power standby (Typical) 325 mW (EMS type: 425 mW)
EMS 0.5 W to 250 W,
5% ±0.5 W (>0.5 W)
Local Input 230 VAC (Max. 265 V)
Binary Input voltage Maximum 265 V (Same phase)
Input contact resistance < 10 kΩreliably ON,
IN to L > 50 kΩreliably OFF
Voltage difference < 1 V reliably ON
IN to L > 3 V reliably OFF
Overload protected (Auto recovery)
Short-circuit protected (Auto recovery)
Dimensions 49.5 x 45.5 x 18 mm (H x W x D)
55°C45°C
* Derating
-5°C
200 W
250 W
Danger
Lebensgefahr
Danger de mort
Nebezpečí
Nebezpečenstvo
Fare
Peligro
Életveszély
Pericolo di morte
Fare
Levensgevaar
Perigo
Niebezpieczenstwo
Varning
Vaara
Hayati Tehlike
Pericol
Installation by electricians only
Montage nur durch Elektrofachkräfte
Montage uniquement par un électricien
Montáž pouze osobami s elektrotechnickou kvalifikaci
Montáž iba osobami s elektrotechnickou kvalifikáciou
Må kun installeres af en aut. el-installatør
Debe ser instalado por un profesional eléctrico
Csak szakképzett személy szerelheti
Montaggio esclusivamente ad opera di personale specializzato
Må monteres av autorisert installatør Gr.L
Montage alleen door elektromonteurs
Deve ser instalado por um profissional
Montaz tylko przez uprawnionych instalatorów
Får endast utföras av behörig elektriker
Asennus vain sähköasentajan toimesta
Sadece uzman kisiler monte edebilir
Instalare numai de catre electricieni
1
MA-CDAU-01/04.qxp/02.2016a
IL019101ZU / 136211185
Eaton Industries (Austria) GmbH, Eugenia 1, 3943 Schrems, Austria
www.eaton.eu/documentation

2
< 0.5 s
PROG
MODE
Current Mode
1x
2x
3x
4x
5x
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
< 0.5 s
MODE
PROG
Set new Mode
Set Local Input Mode / Lokale Ingang toewijzen / Tildele Lokal Inngang /
Zuweisung lokaler Eingang / Přiřazení místního vstupu (CDAU-01/04-I)
< 0.5 s
PROG
MODE
Current Mode
Set Dim Profile / Dim Profiel instellen / Stille inn dimmeprofil /
Einstellen des Dim Profil / Nastavení Dim profil
Wiring diagrams / Aansluitschema's / Koblingsskjemaer /
Schaltpläne / Schéma zapojení
See wiring examples for modes 1, 2, 4 and 5.
Zie bedradingsvoorbeelden modi 1, 2, 4 en 5.
Se koblingseksempler for modi 1, 2, 4 og 5.
Siehe Schaltbeispiele fur die Modi 1, 2, 4 und 5.
Viz Příklady zapojení pro režimy 1, 2, 4 a 5.
See LED compatibility list for correct LED Dim Profile.
Zie de LED-compatibiliteitslijst voor het juiste LED Dim-profiel.
Se LED-kompatibilitetslisten for korrekt LED dimmeprofil.
Siehe LED-Kompatibilitätsliste fur das korrekte LED Dim Profil.
Viz LED seznam kompatibilních pro správnou LED Dim Profilu.
Push button / Pulsdrukker / Trykknapp /
Tastfunktion / Tlaèítko
Switch / Schakelaar / Bryter /
Schalter / Pøepína
Mixed / Gemengd / Blandet /
Mixed / Smíšená
Rocker / Tuimelschakelaar / Vippebryter /
Wippschalter / Kolébkový spínaè
Sensor Mode / Sensor Mode / Sensor Mode /
Sensor-Modus / Mode Sensor

6
PROG
> 2 s MODE
Identify in MRF / Identificeren in MRF / Identifiser i MRF /
Identifizieren im MRF / Identifikace v MRF
PROG
> 2 s
MODE
PROG
< 0.5 s
MODE
ON
OFF
PROG
< 0.5 s
MODE
Manual switching - test / Handmatig schakelen - test / Manuell betjening - test /
Handschaltung - Test / Ruční přepínání / test
Back to factory default / Terug naar fabrieksinstellingen / Tilbake til fabrikkinnstillinger /
Auf Auslieferungszustand zurücksetzen / Zpět na tovární hodnoty
PROG
< 0.5 s
MODE
PROG
< 0.5 s
MODE
PROG
< 0.5 s
MODE
PROG
5x
Remove Sensor in Basic Mode / Sensor in Basic Mode verwijderen / Fjerne i Basic Mode /
Löschen im Basic Mode / Odstranit v základním režimu
PROG
< 0.5 s
MODE
Assign Sensor in Basic Mode / Sensor in Basic Mode toewijzen / Tilknytte i Basic Mode /
Zuweisen im Basic Mode / Přiřadit v základním režimu
PROG
2x

4
Affixing date of CE mark:
2015
Doc.Id.:
CDAU-01/04.. (contains RF-Modul CSCZ-01/xx)
Senior Vice President Director Quality
General Manager & EHS
Friedrich Schröder
Fernando Ceccarelli
Declaration of Conformity
We, EATON Industries (Austria) GmbH
3943 Schrems, Eugenia 1
Austria
declare that product (family)
Eaton - Dimming actuator,
CDAU-01/04.. (contains RF-Modul CSCZ-01/xx)
(the declaration of conformity applies to all
listed types within our actual product catalog)
provided that it is installed, maintained and used in the
application intended for, with respect to the relevant manufacturers
instructions, installation standards and “good engineering practices”
complies with the provisions of Council directive(s):
Low Voltage Directive 2006/95/EC
EMC Directive 2004/108/EC
Radio and Telecommunications Terminal Equipment 99/05/EC
RoHS Directive 2011/65/EU
based on compliance with following standard(s):
EN50491-5-1/10, EN50491-5-2/10, EN60669-2-1/10,
EN50428/05+A1/07+A2/09, EN55015/13, EN61547/09
covered by RF-Modul CSCZ-01/xx: EN301489-3 V1.6.1, EN300220-2
V2.4.1, EN50491-5-1/10, EN50491-5-2/10, EN60950-1/06 + A11/09 +
A1/10 + A12/11 + A2/13, EN62479/10
20.10.2015