Eaton SVX9000 Series User manual

SVX9000 Drives
Quick Start Guide
Effective November 2011
Supersedes December 2003
CONTENT
STEP 1 — Keypad Operation Overview
STEP 2 — Standard Wiring Diagrams and Connections
STEP 3 — Start-Up Wizard
STEP 4 — Operating and Programming Menu
Navigation
STEP 5 — Faults and Warning Indication
STEP 6 — Monitoring Menu
MN04003009E.fm Page 0 Wednesday, November 9, 2011 8:47 AM

1 SVX9000 Drives MN04003009E—November 2011 www.eaton.com
STEP 1
KeypadOperation Overview
KeypadandDisplay
LCD Status Indicators
LED Status Indicators
Indicator Description
Run
Indicates that the SVX9000 is running and controlling the load. Blinks
when a stop command has been given but the SVX9000 is still
ramping down.
Counterclockwise Operation
The output phase rotation is BAC, corresponding to counterclockwise
rotation of most motors.
Clockwise Operation
The output phase rotation is ABC, corresponding to clockwise rotation
of most motors.
Stop
Indicates that the SVX9000 is stopped and not controlling the load.
Ready
Indicates that the SVX9000 is ready to be started.
Alarm
Indicates that there is one or more active drive alarm(s).
Fault
Indicates that there is one or more active drive fault(s).
I/O Terminal
Indicates that the I/O terminals have been chosen for control.
Keypad
Indicates that the keypad has been chosen for control.
Bus/Communications
Indicates that the communications bus control has been chosen for
control.
Indicator Description
local Local — Steady Illumination
Indicates that the SVX9000 is ready to be started and operated from
the Local mode.
Local — Flashing
Indicates that the SVX9000 is ready for operating command to select
Local or Remote operation.
remote Remote
Indicates that the SVX9000 is operating and controlling the load
remotely.
Remote — Flashing
Indicates that the SVX9000 is ready for operating command to select
Local or Remote operation.
fault Fault
Indicates that there is one or more active drive fault(s).
MN04003009E.fm Page 1 Wednesday, November 9, 2011 8:47 AM

SVX9000 Drives MN04003009E—November 2011 www.eaton.com 2
STEP 1 (Continued)
Navigation Buttons
Menu Navigation
Navigation Tips
To navigate within one level of a menu, use the up and down arrows.
To move deeper into the menu structure and back out, use the right
and left arrows.
To edit a parameter, navigate to show that parameter’s value, and press
the right arrow button to enter the edit mode. In edit mode, the
parameter value will flash.
Button Description
Start
This button operates as the START button for normal operation when
the “Keypad” is selected as the active control.
Enter
This button is used in the parameter edit mode to save the parameter
setting and move to the next parameter …
•to reset the Fault History if pressed while in the “Fault History”
menu.
•to confirm the acceptance of a change.
•to change a virtual button status while in the “Button” menu.
•to confirm the start-up list at the end of the Start-Up Wizard.
•when the “Operate” menu is active, to exit the “Operate” submenu.
Stop
This button has two integrated operations. The button operates as
STOP button during normal operation …
•motor STOP from the keypad, which is always active unless
disabled by the “StopButtonActive” parameter.
•used to reset the active faults.
Reset
Resets the active faults.
Local / Remote
Switches between LOCAL and REMOTE control for start, speed
reference and reverse functions. The control locations corresponding
to local and remote can be selected within an application.
Left Arrow
•navigation button, movement to left.
•in parameter edit mode, exits mode, backs up one step.
•cancels edited parameter (exit from a parameter edit mode).
•When in “Operate” menu will move backward through menu.
•At end of “Start-Up Wizard”, repeats the “Start-Up Wizard”
setup menu.
Right Arrow
•navigation button, movement to right.
•enter parameter group mode.
•enter parameter mode from group mode.
•When in “Operate” menu will move forward through menu.
Up andDown Arrows
•move either up or down a menu list to select the desired menu item.
•editing a parameter/password, while the active digit/character is
scrolled.
•increase/decrease the reference value of the selected parameter.
•in the “Operate” menu, will cause the display of the active reference
source and value and allow its change if the keypad is the active
reference source. Used to set the password (if defined) when
leaving the “Operate” menu.
•scroll through the “Active Faults” menu when the SVX9000 is
stopped.
MN04003009E.fm Page 2 Wednesday, November 9, 2011 8:47 AM

3 SVX9000 Drives MN04003009E—November 2011 www.eaton.com
STEP 1 (Continued)
When in edit mode, the parameter value can be changed by pressing
the up or down arrow keys.
When in edit mode, pressing the right arrow a second time will allow
you to edit the parameter value digit by digit.
To confirm the parameter change you must press the ENTER button.
The value will not change unless the ENTER button is pushed.
Some parameters can not be changed while the SVX9000 is running.
The screen will display LOCKED if you attempt to edit these parameters
while the drive is running. Stop the drive to edit these parameters. See
the SVX9000 Application Manual for identification of these parameters
specific to your chosen application.
Main Menu
The data on the control keypad are arranged in menus and submenus. The
first menu level consists of M1 to M8 and is called the Main Menu. The Main
Menu is illustrated on Page 7. Some of the submenus will vary for each
application choice.
STEP 2
StandardWiring Diagrams andTerminal Locations
Power and Motor Wiring Terminal Schematic for SVX9000 Drives
SVX9000 Power andMotor Wiring for Low Horsepower Drives (1 – 30 hp)
UVW
B+
M
3~
L1 L2 L3
L1 L2 L3 B- R- T1T2T3
External
RFI-Filter
(Optional)
BR
(Optional)
External
Filter
(Optional)
BR
Power
Board
230V 1 – 15 hp
480V 1-1/2 – 30 hp
Control
Board
MN04003009E.fm Page 3 Wednesday, November 9, 2011 8:47 AM

SVX9000 Drives MN04003009E—November 2011 www.eaton.com 4
STEP 2 (Continued)
SVX9000 Power andMotor Wiring for
Large Horsepower Drives (20 – 250 hp)
B+
M
3~
L1 L2 L3
L1 L2 L3 B- R-
External
RFI-Filter
(Optional)
BR
(Optional)
External
Filter
(Optional)
BR
Power
Board
230V 20 – 30 hp
480V 40 – 250 hp
Control
Board
UVW
T1T2T3
MN04003009E.fm Page 4 Wednesday, November 9, 2011 8:47 AM

5 SVX9000 Drives MN04003009E—November 2011 www.eaton.com
STEP 2 (Continued)
Standard Application Default I/O Configuration
Note: For more information on jumper selections, see the
9000X AF Drives User Manual , Chapter 4 .
Terminal Signal Description
OPTA1
1 +10V
ref
Reference output Voltage for potentiometer,
etc.
2 AI1+ Analog input,
voltage range
0 – 10V DC
Voltage input frequency
reference
3 AI1- I/O Ground Ground for reference and
controls
4 AI2+ Analog input,
current range
0 – 20 mA
Current input frequency
reference
5 AI2-
6 +24V Control voltage
output
Voltage for switches, etc.
max 0.1A
7 GND I/O ground Ground for reference and
controls
8 DIN1 Start forward
(programmable)
Contact closed = start forward
9 DIN2 Start reverse
(programmable)
Contact closed = start reverse
10 DIN3 External
fault input
(programmable)
Contact open= no fault
Contact closed = fault
11 CMA Commonfor DIN1
– DIN3
Connect to GND or +24V
12 +24V Control voltage
output
Voltage for switches (see #6)
13 GND I/O ground Ground for reference and
controls
14 DIN4 Multi-step speed
select 1
DIN4 DIN5 Frequency
ref.
15 DIN5 Multi-step speed
select 2
Open
Closed
Open
Closed
Open
Open
Closed
Closed
Ref.U
in
Multi-step
ref.1
Multi-step
ref.2
Ref.I
in
16 DIN6 Fault reset Contact open= no action
Contact closed = fault reset
17 CMB Commonfor DIN4
– DIN6
Connect to GND or +24V
18 AO1+ Output frequency
Analog output
Programmable
Range 0 – 20 mA/R
L
,
max. 500 W
19 AO1-
20 DO1 Digital output
READY
Programmable
Opencollector, I
≤ 50 mA,
U ≤ 48V DC
OPTA2
21 RO1 Relay
output 1
RUN
22 RO1
23 RO1
24 RO2 Relay
output 2
FAULT
25 RO2
26 RO2
CMB connected to GND
CMA connected to GND
CMB isolated from GND
CMA isolated from GND
CMB and CMA internally connected
together, isolated from GND
= Factory default.
Jumper Block X3:
CMA andCMB Grounding
RUN
Reference
1 – 10 kW
mA
READY
220V
AC
potentiometer
MN04003009E.fm Page 5 Wednesday, November 9, 2011 8:47 AM

SVX9000 Drives MN04003009E—November 2011 www.eaton.com 6
STEP 3
Start-Up Wizard
If the wizard is not enabled at power-up, press the STOP button for 5 secs.
to enable it.
Accel. Time 1
“3.0” s
Decel Time 1
“3.0” s
Current Limit
“3.30” A
Motor NP Volt
“460” V
Motor NP Freq
“60.00” Hz
Motor NP Speed
“1720” rpm
Motor NP Current
“2.20” A
Power Factor
“0.85”
Loc. Ctrl. Place
“Keypad”
Input Phase Supv
“Fault, Coast”
Repeat Setup?
<No Yes>
Rem. Ctrl. Place
“I/O Terminal”
Local Reference
“Keypad”
Remote Reference
“AI1”
Startup Wizard
“Press Enter”
Language
“English”
Application
“Standard”
3 – 5 Seconds Wait
Setup Starts
“Press Enter”
Min. Freq
“0.00” Hz
Max. Freq
“60.00” Hz
Setup Done
Press Enter
Copy Parameters
<No Yes>
Up to Keypad
<No Yes>
Up to Keypad
Wait
Output Frequency
“0.00” Hz
MN04003009E.fm Page 6 Wednesday, November 9, 2011 8:47 AM

7 SVX9000 Drives MN04003009E—November 2011 www.eaton.com
STEP 4
Operating & Programming Menu Navitation
Main Menu
The data on the control keypad are arranged in menus and submenus. The
first menu level consists of M1 to M8 and is called the Main Menu. The
structure of these menus and their submenus is illustrated below. Some of
the submenus will vary for each application choice.
Main Menu Navigation
Note: Enter Key — Holding the “Enter” key for more than 3 seconds will
allow you to go directly to the programming mode.
M1 Parameters
M2 Keypad Control
M3 Active Faults
M6 Expander Boards
M7 Monitor
M8 Operate Mode
G1.1
. . .
. . .
R2.1 Keypad Reference
P2.2 Keypad Direction
P2.x Stop ButtonActive
A3.1 Active Fault 1
T3.1.1 OperationDays
. . .
T3.1.13 Zero Speed
A3.x Active Fault x
V7.1 Output Frequency–0.00 Hz
V7.2 Frequency Reference–0.00 Hz
. . .
G1.x
G6.1 Slot A Board
. . .
G6.5 Slot E Board
O1 Output Frequency–0.0 Hz
O2 Freq Reference–0.0 Hz
. . .
Ox . . .
+
+
+
+
+
M7.1x Multimonitor
Menu Navigation:
Up Arrow — The up arrow
advances to the next
menu item.
For example, pressing the
up arrow once will
advance from M1 to M2.
Down Arrow — The down
Right Arrow — The right
Left Arrow — The left
arrow backs up to the
previous menu item.
arrow will advance to the
next level inthe menu.
arrow will back up one
level inthe menu
structure.
For example, pressing the
downarrow once will back
up from M2 to M1.
For example, pressing the
right arrow once will
advance from M2 to R2.1.
For example, pressing the
left arrow once will back
up from R2.1 to M2.
+
+
M5 System Menu
S5.1 Language
S5.2 Application
S5.3 Copy Parameters
+
S5.4 Compare Parameters
S5.5 Security
S5.6 Keypad Settings
S5.7 Hardware Settings
S5.8System Information
. . .
M4 Fault History
H4.1 Most Recent Fault
T4.1.1 OperationDays
. . .
T4.1.13 Zero Speed
N7.1x.1
H4.1.x Oldest Saved Fault
. . .
MN04003009E.fm Page 7 Wednesday, November 9, 2011 8:47 AM

SVX9000 Drives MN04003009E—November 2011 www.eaton.com 8
STEP 4 (Continued)
Operate Menu — M8
The Operate Menu provides a easy to use method of viewing key numerical
Monitoring Menu items. Some applications also support the setting of
reference values in this menu. The items displayed vary by application. The
table below is an example for the Standard application.
Operate Menu Items — StandardApplication Example
The menu is navigated by using the left and right arrow buttons. If a
reference level is available for setting, the up and down arrow buttons adjust
the value. To exit the Operate Menu to access the other menus, depress the
ENTER button for 2 seconds. While in the other menus, if there is no keypad
activity, the display will return to the Operate Menu after 30 seconds.
Code Signal Name Unit Description
O.1 Output Frequency Hz Output frequency
O.2 FreqReference Hz Frequency reference
O.3 Motor Speed rpm Calculated motor speed
O.4 Motor Current A Measured motor current
O.5 Motor Torque % Calculated torque based on nominal motor
torque
O.6 Motor Power % Calculated power based on nominal motor
power
O.7 Motor Voltage V Calculated motor voltage
O.8 DC-Bus Voltage V Measured DC-bus voltage
O.9 Unit Temperature °C Heatsink temperature
O.10 MotorTemperature % Calculated motor temperature based on the
motor nameplate information and the
calculated motor load
R1 Keypad Reference Hz Keypad frequency reference setting
MN04003009E.fm Page 8 Wednesday, November 9, 2011 8:47 AM

9 SVX9000 Drives MN04003009E—November 2011 www.eaton.com
STEP 4 (Continued)
Parameters — M1
Standard Parameters — M1

Parameter value canonly be changed after the drive has beenstopped.
Code Parameter Min. Max. Unit Default Cust ID Note
P1.1.1 Min
frequency
0.00 Par.
1.1.2
Hz 0.00 101
P1.1.2 Max
frequency
Par.
1.1.1
320.00 Hz 60.00 102 NOTE : If f
max
>
thanthe motor
synchronous
speed, check
suitability for
motor and drive
system.
P1.1.3 Acceleration
time 1
0.1 3000.0 s 3.0 103
P1.1.4 Deceleration
time 1
0.1 3000.0 s 3.0 104
P1.1.5 Current limit 0.1 x
I
H
2 x I
H
AI
L
107
P1.1.6

Nominal
voltage of
the motor
180 690 V P: 230V
P: 460V
P: 575V
110
P1.1.7

Nominal
frequency of
the motor
30.00 320.00 Hz 60.00 111 Check the rating
plate of the
motor.
P1.1.8

Nominal
speed of the
motor
300 20 000 rpm 1720 112 The default applies
for a 4-pole motor
and a nominal
size frequency
converter.
P1.1.9

Nominal
current of the
motor
0.1 x
I
H
2 x I
H
AI
H
113 Check the rating
plate of the
motor.
P1.1.10

Power Factor 0.30 1.00 0.85 120 Check the rating
plate of the
motor.
P1.1.11 Local Control
Place
1 3 2 171 1 = I/O Terminal
2 = Keypad
3 = Fieldbus
P1.1.12 Remote
Control
Place
1 3 1 172 1 = I/O Terminal
2 = Keypad
3 = Fieldbus
P1.1.13

Local
reference
0 3 2 173 0 = AI1
1 = AI2
2 = Keypad
3 = Fieldbus
P1.1.14

Remote
reference
0 3 0 174 0 = AI1
1 = AI2
2 = Keypad
3 = Fieldbus
P1.1.15 Identification0 2 0 631 0 = Not used
1 = V/Hz
2 = V/Hz with
boost
P1.1.16 V/Hz Opt 0 1 0 109 0 = Not used
1 = Automatic
torque boost
P1.1.17 Preset
speed 1
0.00 Par.
1.1.2
Hz 10.00 105 Speeds preset by
operator.
P1.1.18 Preset
speed 2
0.00 Par.
1.1.2
Hz 40.00 106
MN04003009E.fm Page 9 Wednesday, November 9, 2011 8:47 AM

SVX9000 Drives MN04003009E—November 2011 www.eaton.com 10
STEP 4 (Continued)
Input Signals — M1
➔
G1.2

Parameter value canonly be changed after the drive has beenstopped.

Use TTF method to program these parameters.

Rising edge required to start.

CP = control place.
Output Signals — M1 ➔ G1.3

Parameter value canonly be changed after the drive has beenstopped.
Code Parameter Min. Max. Unit Default Cust ID Note
P1.2.1

Start/Stop
logic
0 6 0 300 DIN1 DIN2
0
1
2
3
4
5
6
Start fwd
Start/Stop
Start/Stop
Start
pulse
Fwd

Start

/
Stop
Start

/
Stop
Start rvs
Rvs/Fwd
Run
enable
Stop
pulse
Rvs

Rvs/
Fwd
Run
enable
P1.2.2

DIN3
function
0 7 1 301 0 = Not used
1 = Ext. fault. closing
cont.
2 = Ext. fault. opening
cont.
3 = Runenable
4 = Acc./Dec. time select.
5 = Force CP to
Remote

6 = Rvs (if par. 1.2.1 = 3)
P1.2.3 Current
reference
offset
0 1 1 302 0 = 0 – 20mA
1 = 4 – 20mA
P1.2.4 Reference
scaling
minimum
value
0.00 Par.
1.2.5
Hz 0.00 303 Selects the frequency
that corresponds to the
min. reference signal
0.00 = No scaling
P1.2.5 Reference
scaling
maximum
value
0.00 320.00 Hz 0.00 304 Selects the frequency
that corresponds to the
max. reference signal
0.00 = No scaling
P1.2.6 Reference
inversion
0 1 0 305 0 = Not inverted
1 = Inverted
P1.2.7 Reference
filter time
0.00 10.00 s 0.10 306 0
= No filtering
P1.2.8

AI1 signal
selection
A.1 377 TTF programming
method used.
P1.2.9

AI2 signal
selection
A.2 388 TTF programming
method used.
Code Parameter Min. Max. Unit Default Cust ID Note
P1.3.1

Analog
output 1
signal
selection
0 A.1 464 TTF programming
method used.
P1.3.2 Analog
output
function
0 8 1 307 0 = Not used
1 = Output freq.
(0 – f
max
)
2 = Freq. reference
(0 – f
max
)
3 = Motor speed
(0 – Motor nominal
speed)
4 = Motor current
(0 – I
nMotor
)
5 = Motor torque
(0 – T
nMotor
)
6 = Motor power
(0 – P
nMotor
)
7 = Motor voltage
(0 – U
nMotor
)
8 = DC-Bus volt
(0 – 1000V)
P1.3.3 Analog
output
filter time
0.00 10.00 s 1.00 308 0 = No filtering
MN04003009E.fm Page 10 Wednesday, November 9, 2011 8:47 AM

11 SVX9000 Drives MN04003009E—November 2011 www.eaton.com
STEP 4 (Continued)
Output Signals — M1
➔
G1.3 (Continued)

Parameter value canonly be changed after the drive has beenstopped.
Code Parameter Min. Max. Unit Default Cust ID Note
P1.3.4 Analog output
inversion
0 1 0 309 0 = Not inverted
1 = Inverted
P1.3.5 Analog output
minimum
0 1 0 310 0 = 0 mA
1 = 4 mA
P1.3.6 Analog output
scale
10 1000 %100 311
P1.3.7 Digital output 1
function
0 16 1 312 0 = Not used
1 = Ready
2 = Run
3 = Fault
4 = Fault inverted
5 = FC overheat
warning
6 = Ext. fault or
warning
7 = Ref. fault or
warning
8 = Warning
9 = Reversed
10 = Preset
speed 1
11 = At speed
12 = Mot.
regulator
active
13 = OP freq.
limit 1
superv.
14 = Remote
Control
Active
15 = Thermistor
fault/warng
16 = Fieldbus
input data
P1.3.8 Relay output 1
function
0 16 2 313 Same as
parameter 1.3.7
P1.3.9 Relay output 2
function
0 16 3 314 Same as
parameter 1.3.7
P1.3.10 Output
frequency limit
1 supervision
0 2 0 315 0 = No limit
1 = Low limit
supervision
2 = High limit
supervision
P1.3.11 Output
frequency limit
1; Supervised
value
0.00 320.00 Hz 0.00 316
P1.3.12

Analog output
2 signal
selection
0 0.1 471 TTF
programming
method used.
P1.3.13 Analog output
2 function
0 8 4 472 Same as
parameter 1.3.2
P1.3.14 Analog output
2 filter time
0.00 10.00 s 1.00 473 0 = No filtering
P1.3.15 Analog output
2 inversion
0 1 0 474 0 = Not inverted
1 = Inverted
P1.3.16 Analog output
2 minimum
0 1 0 475 0 = 0 mA
1 = 4 mA
P1.3.17 Analog output
2 scaling
10 1000 %100 476
MN04003009E.fm Page 11 Wednesday, November 9, 2011 8:47 AM

SVX9000 Drives MN04003009E—November 2011 www.eaton.com 12
STEP 4 (Continued)
Drive Control Parameters — M1
➔
G1.4

Parameter value canonly be changed after the drive has beenstopped.
Prohibit Frequencies — M1 ➔ G1.5
Code Parameter Min. Max. Unit Default Cust ID Note
P1.4.1 Ramp 1
shape
0.0 10.0 s 0.0 500 0 = Linear
>0 = S-curve ramp
time
P1.4.2 Ramp 2
shape
0.0 10.0 s 0.0 501 0 = Linear
>0 = S-curve ramp
time
P1.4.3 Acceleration
time 2
0.1 3000.0 s 10.0 502
P1.4.4 Deceleration
time 2
0.1 3000.0 s 10.0 503
P1.4.5

Brake
chopper
0 4 0 504 0 = Disabled
1 = Used when
running
2 = External brake
chopper
3 = Used when
stopped/
running
4 = Used when
running (no
testing)
P1.4.6 Start function0 1 0 505 0 = Ramp
1 = Flying start
P1.4.7 Stop function0 3 1 506 0 = Coasting
1 = Ramp
2 = Ramp+Run
enable coast
3 = Coast+Run
enable ramp
P1.4.8 DC braking
current
0.00 I
L
A 0.7 x I
H
507
P1.4.9 DC braking
time at stop
0.00 600.00 s 0.00 508 0 = DC brake is off
at stop
P1.4.10 Frequency to
start DC
braking
during
ramp stop
0.10 10.00 Hz 1.50 515
P1.4.11 DC braking
time at start
0.00 600.00 s 0.00 516 0 = DC brake is off
at start
P1.4.12 Flux brake 0 1 0 520 0 = Off
1 = On
P1.4.13 Flux braking
current
0.1
x I
H
I
L
AI
H
519
Code Parameter Min. Max. Unit Default Cust ID Note
P1.5.1 Skipfrequency
range 1 low
limit
0.00 Par.
1.5.2
Hz 0.00 509
P1.5.2 Skipfrequency
range 1 high
limit
0.00 Par.
1.1.2
Hz 0.0 510 0 = Skip frequency
range 1 not
used
P1.5.3 Skipfrequency
acc./dec. ramp
0.1 10.0 1.0 518
MN04003009E.fm Page 12 Wednesday, November 9, 2011 8:47 AM

13 SVX9000 Drives MN04003009E—November 2011 www.eaton.com
STEP 4 (Continued)
Motor Control Parameters — M1
➔
G1.6

Parameter value canonly be changed after the drive has beenstopped.
Output Signals — M1 ➔ G1.3
Code Parameter Min. Max. Unit Default Cust ID Note
P1.6.1

Motor
control
mode
0 1/6 0 600 SVX:
0 = Frequency
control
1 = Speed control
Additionally for
SPX:
2 = Torque control
3= Closed loop
speed ctrl
4= Closed loop
torque ctrl
P1.6.2

V/Hz
optimization
0 1 0 109 0= Not used
1= Automatic
torque boost
P1.6.3

V/Hz ratio
selection
0 3 0 108 0= Linear
1= Squared
2= Programmable
3= Linear with
flux optim.
P1.6.4

Field
weakening
point
8.00 320.00 Hz 60.00 602
P1.6.5

Voltage at
field
weakening
point
10.00 200.00 %100.00 603 n% x Unmot
P1.6.6

V/Hz curve
midpoint
frequency
0.00 Par.
1.6.4
Hz 60.00 604
P1.6.7

V/Hz curve
midpoint
voltage
0.00 100.00 %100.00 605 n% x Unmot
Parameter max.
value = par. 2.6.5
P1.6.8

Output
voltage at
zero
frequency
0.00 40.00 %1.30 606 n% x Unmot
P1.6.9 Switching
frequency
1.0 Varies kHz Varies 601 See Table 8-12 on
page 57 for exact
values
P1.6.10 Overvoltage
controller
0 2 1 607 0= Not used
1= Used (no
ramping)
2= Used (ramping)
P1.6.11 Undervoltage
controller
0 1 1 608 1= Yes
2= No
P1.6.12 Load
Drooping
0.00 100.00 0.00 620 Drooping %of
nominal speed at
nominal torque
P1.6.13 Identification0 1 0 631 0= Not used
1= OL v/f Ratio
2= OL v/f and
Boost
Code Parameter Min. Max. Unit Default Cust ID Note
P1.7.1 Response to
reference
fault
0 6 6 700 0= No response
1= Warning
2= Warning+
Previous Freq.
3= Wrng+
PresetFreq
1.7.2
4= Fault.stop acc.
to 1.4.7
5= Fault.stop by
coasting
6= Fault, Restart
MN04003009E.fm Page 13 Wednesday, November 9, 2011 8:47 AM

SVX9000 Drives MN04003009E—November 2011 www.eaton.com 14
STEP 4 (Continued)
Protections — M1 ➔ G1.7
Code Parameter Min. Max. Unit Default Cust ID Note
P1.7.2 Reference fault
frequency
0.00 Par.
1.1.2
Hz 0.00 728
P1.7.3 Response to
external fault
0 3 2 701 0= No response
1= Warning
2= Fault.stop
acc. to 1.4.7
3= Fault.stop
by coasting
P1.7.4 Input phase
supervision
0 3 3 730
P1.7.5 Response to
undervoltage
fault
1 3 0 727
P1.7.6 Output phase
supervision
0 3 2 702
P1.7.7 Earth fault
protection
0 3 2 703
P1.7.8 Thermal
protectionof
the motor
0 3 2 704
P1.7.9 Motor ambient
temperature
factor
-100.0 100.0 %0.0 705
P1.7.10 Motor cooling
factor at zero
speed
0.0 150.0 %40.0 706
P1.7.11 Motor thermal
time constant
1 200 min45 707
P1.7.12 Motor duty
cycle
0 100 %100 708
P1.7.13 Stall protection0 3 0 709 0= No response
1= Warning
2= Fault.stop
acc. to 1.4.7
3= Fault.stop
by coasting
P1.7.14 Stall current 0.1 InMotor
x 2
AI
L710
P1.7.15 Stall time limit 1.00 120.00 s 15.00 711
P1.7.16 Stall frequency
limit
1.0 Par.
1.1.2
Hz 25.0 712
P1.7.17 Underload
protection
0 3 0 713 0= No response
1= Warning
2= Fault.stop
acc. to 1.4.7
3= Fault.stop
by coasting
P1.7.18 Field
weakening area
load
10 150 %50 714
P1.7.19 Zero frequency
load
5.0 150.0 %10.0 715
P1.7.20 Underload
protectiontime
limit
2 600 s 20 716
P1.7.21 Response to
thermistor fault
0 3 2 732 0= No response
1= Warning
2= Fault.stop
acc. to 1.4.7
3= Fault.stop
by coasting
P1.7.22 Response to
fieldbus fault
0 3 2 733 See P1.7.21
P1.7.23 Response to
slot fault
0 3 2 734 See P1.7.21
P1.7.24 FB MCW Bit 15 0 2 0 771 0= No action
1= Fault low
2= Fault high
MN04003009E.fm Page 14 Wednesday, November 9, 2011 8:47 AM

15 SVX9000 Drives MN04003009E—November 2011 www.eaton.com
STEP 4 (Continued)
Auto Restart Parameters — M1 ➔ G1.8
Keypad Control — M2
This menu provides the parameters for the setting of the keypad frequency
reference, the selection of motor direction when in keypad operation, and
when the STOP button is active.
Keypad Control Parameters — M2
Other Menus — M3 to M6
Menus M3 to M6 provide information on the Active Faults, Fault History,
System Menu settings and the Expander Board setup. These menu items are
explained in detail in Chapter 5 of the SVX9000 User Manual.
Code Parameter Min. Max. Unit Default Cust ID Note
P1.8.1 Wait time 0.10 10.00 s 0.50 717
P1.8.2 Trial time 0.00 60.00 s 30.00 718
P1.8.3 Start function0 2 0 719 0= Ramp
1= Flying start
2= According to
par. 1.4.6
P1.8.4 Number of tries
after
undervoltage
trip
0 10 0 720
P1.8.5 Number of tries
after
overvoltage
trip
0 10 0 721
P1.8.6 Number of tries
after
overcurrent trip
0 3 0 722
P1.8.7 Number of tries
after reference
trip
0 10 0 723
P1.8.8 Number of tries
after motor
temperature
fault trip
0 10 0 726
P1.8.9 Number of tries
after external
fault trip
0 10 0 725
P1.8.10 Number of tries
after underload
fault trip
0 10 0 738
Code Parameter Min. Max. Unit Default Cust ID Note
P2.1 Control place 0 3 0 1685 0= Keypad L/R
1= Local
2= Remote
3= I/O force
R2.1 Keypad
reference
Par.
1.1.1
Par.
1.1.2
Hz
P2.3 Direction(on
keypad)
0 1 0 123 0= Forward
1= Reverse
P2.4 Stop button0 1 1 114 0= Limited
functionof
Stop button
1= Stop button
always
enabled
P2.5 Operate menu
hide
0 1 0 1688 0= No
1= Yes
MN04003009E.fm Page 15 Wednesday, November 9, 2011 8:47 AM

SVX9000 Drives MN04003009E—November 2011 www.eaton.com 16
STEP 5
Faults and Fault Codes
Code/Fault Directory
Fault
Code Fault
Fault
Code Fault
Fault
Code Fault
1Overcurrent 16 Motor
overtemperature
40 Device unknown
2Overvoltage 17 Motor underload 41 IGBT temperature
3Ground (Earth)
Fault
22 EEPROM
checksum fault
42 Brake resistor
overtemperature
5Charging Switch 24 Counter fault 43 Encoder fault
6Emergency stop 25 Microprocessor
watchdog fault
44 Device change
(different type)
7Saturation trip 26 Startup prevented 45 Device added
(different type)
8System fault 29 Thermistor fault 50 Analog input I
in
< 4 mA (for the
signal range 4 to
20 mA)
9Undervoltage 31 IGBT temperature
(hardware)
51 External fault
10 Input line
supervision
32 Fan heat sink 52 Keypad
communication
fault
11 Output phase
supervision
34 CAN bus
communication
53 Communication
bus fault
12 Brake chopper
supervision
36 Control unit 54 Slot fault
13 SVX9000
undertemperature
37 Device change
(same type)
56 PT100 board
temperature fault
14 SVX9000
overtemperature
38Device added
(same type)
——
15 Motor stalled 39 Device removed ——
MN04003009E.fm Page 16 Wednesday, November 9, 2011 8:47 AM

17 SVX9000 Drives MN04003009E—November 2011 www.eaton.com
STEP 6
Monitoring Menu — M7
The Monitoring Menu items are meant for viewing parameter values during
operation. Monitored values are updated every 0.3 sec. Monitored items are
identified by item numbers V7.1 to V1.xx, where “xx” varies by application.
The table below provides an example of the monitored values for the
Standardapplication.
Monitored parameters are not editable from this menu (See Parameter
Menu [M1] to change parameter values).
Monitoring Menu Items — StandardApplication Example
Digital Inputs — DIN1, DIN2, DIN3 Status
Digital Inputs — DIN4, DIN5, DIN6 Status
Digital andRelay Outputs — DO1, RO1, RO2 Status
Multimonitor (V7.17)
This parameter allows the viewing and selection (if allowed by System
menu item, P5.5.4) of three simultaneously monitored items from the
Monitored Menu Items shown in the table above. Use the right arrow key to
select the item to be modified and then the up or down arrow keys to select
the new item. Press the ENTER key to accept the change.
Code Signal Name Unit Description
V7.1 Output
Frequency
Hz Output frequency
V7.2 Frequency
reference
Hz Frequency reference setting
V7.3 Motor speed rpm Calculated motor speed
V7.4 Motor current A Measured motor current
V7.5 Motor torque % Calculated torque based on nominal motor torque
V7.6 Motor power % Calculated power based on nominal motor power
V7.7 Motor voltage V Calculated motor voltage
V7.8 DC bus voltage V Measured DC-bus voltage
V7.9 Unit temperature °C Heatsink temperature
V7.10 Calculated motor
temperature
°C Calculated motor temperature based on the
motor nameplate information and the calculated
motor load
V7.11 Analog Input 1 V Voltage input at Terminals AI1+ and GND
V7.12 Analog input 2 mA Current input at Terminals AI2+ and AI2-
V7.13 DIN1, DIN2, DIN3 — Digital input status (see figure below)
V7.14 DIN4, DIN5,DIN6 — Digital input status (see figure below)
V7.15 DO1, RO2, RO3 — Digital and relay output status (see figure below)
V7.16 Analog I
out
mA Current output at Terminals AO1+ and AO1-
V7.17 Multimonitor (See below)
V1.13
DIN1, DIN2, DIN3
OFF ON OFF
V1.14
DIN4, DIN5, DIN6
ON OFF OFF
V1.15
DO1, RO1, RO2
OFF OFF ON
MN04003009E.fm Page 17 Wednesday, November 9, 2011 8:47 AM

MN04003009E.fm Page 18 Wednesday, November 9, 2011 8:47 AM

Eaton Corporation
Electrical Sector
1111 Superior Ave.
Cleveland, OH 44114
United States
877-ETN-CARE (877-386-2273)
Eaton.com
© 2011 Eaton Corporation
All Rights Reserved
Printed in USA
Publication No. MN04003009E / Z11191
November 2011
Eaton is a registered
trademark of Eaton
Corporation.
All other trademarks
are property of their
respective owners.
Eaton is dedicated to ensuring that reliable, efficient
and safe power is available when it’s needed most.
With unparalleled knowledge of el
ectrical power
management across industries,
experts at Eaton
deliver customized, integrated solutions to solve our
customers’ most critical challenges.
Our focus is on delivering the right solution for the
application. But, de
cision makers demand more than
just innovative products.
They turn to Eaton for an
unwavering commitment to personal support that
makes customer success a top priority. For more
information,
visit www.eaton.com/electrical.
MN04003009E.fm Page 19 Wednesday, November 9, 2011 8:47 AM