Eaton Memshield 3 Series Manual

IMPORTANT NOTES
1. This product should be installed, commissioned and maintained by or under the supervision of a competent electrician
in accordance with current electrical engineering Codes of Practice, Regulations for the Electrical equipment of
Buildings (BS7671), CDM2007 - Construction (Design and Management) Regulations 2007, HSG150 - Health and
Safety in Construction, Statutory requirements and any Specific instruction issued by the Company.
2. After completing the installation and testing of this product it is essential that this leaflet is drawn to the attention of
the person responsible for its future operation and maintenance, and is at all times available for ready reference.
3. These notes assume throughout that the product is disconnected from the supply. It is essential that this is done
before any work is carried out.
4. These Panelboards are only designed for use with Eaton MCCBs. Failure to comply will result in invalid warranty and certification.
5. Operation of the incoming and outgoing devices should only be carried out by an instructed or skilled person.
Memshield 3 250A Panelboard/Pan Assemblies
EPBN1425, EPBN1625, EPBN1825, EPBN11225
EPBPN1425, EPBPN1625, EPBPN1825, EPBPN11225
Instruction leaflet LT1208 (12/19)
250A MCCB INCOMER FITTING EPBKN1253, EPBKN1254
250A DIRECT CABLE INCOMER FITTING EPBKN125L
NOTE: When Top Fed, MCCB terminations must be reversed
OUTGOING MCCB AND BLANK FITTING EPBN1BP1
250A PAN ASSEMBLY DIMENSIONS
EPBPN1425 - EPBPN11225
CAT N0. A B C D
EPBPN1425 29.5 483 592.5 181.5
EPBPN1625 29.5 578.5 683 272
EPBPN1825 131 669 773.5 362.5
EPBPN11225 131 850 954.5 543.5
177.8
Min
Inside
Door
A
B
C
459 10.510.5
250A CABLE BOX, EXTENSION BOX, FILLER BOX AND
DIN ENCLOSURE
EPBN1425SXB -
EPBN11225SXB,
EPBN1XE250,
EPBN1CX250,
EPBN1EXDIN
Box fixing
15Nm
Click into
Cover aperture
14Nm
Locate
and click
NB - Provision to reposition Earth
Terminals in Cable Box
M5
Fixings
COVER APERTURES
152.5
D
108.1
130
102
123
InsideCover
69.569.5
14Nm
14Nm
IMPORTANT:
Fit MCCB with the adjustment
dial end towards the Busbar.
All Dimensions
in millimetres
(Terminal Screw)
6Nm
15Nm

LH OUTGOING CIRCUITS RH OUTGOING CIRCUITS
Warning -
Intellectual Property Rights
Eaton wishes to make it clear that it owns intellectual property rights in the
product which it manufactures (whether or not lis ted in thisleaflet) and that
it will take legal action against any party found to be manufacturing, using,
or selling any article which infringes the company’s intelle ctual property.All
marks in this document identified with an Rsymbol or aTM symbol adjacent
to the mark are trademarks of Eaton.
C
2019 Eaton Electric Limited.
All rights reserved.
The use to which this product is put and its place of installation is outside our
control. Particular care should therefore be taken to follow the instructions given
here and to ensure their continued availability in conjunction with the use of the
product.
No responsibility can be accepted by us if these instructions are disregarded.
Further copies of these instructions and information concerning the installation
and proper use of this product can be obtained by contacting the:
Technical Services Department
Eaton Electric Limited, Middleton, Manchester. M24 7GQ
Tel: [phone],
email: [email protected]
www.eaton.com/recycling
TOP ENTRY
LABEL FITTING
Ensure all way labels are fitted in the correct places
BOTTOM FEED TOP FEED
Phase
Label
Earth
Labels
Busbar
Way
Label
Phase
Label
L1 L1
L1
L1
Alternative Earth position
(both sides)
Main
Cover
Prior to cabling, check pan assembly alignment with main cover
Panelboards are supplied ready for bottom entry.
For top entry convert as shown below.
KEY LOCK FITTING
EPBDLK1
FED FROM:
INCOMING CABLE SIZE:
INSTALLATION DATE:
CONTRACTOR:
TOP FEED ADAPTOR FITTING EPBKTFSN2
USED IN CONJUNCTION WITH EPBKN1253 AND EPBKN1254
Busbar
Way
Label
Adaptor
Shield
Rotate Inner Cover
and Pan assembly
1800
Cover Way
Label
Cover Way
Label