Eaton Memshield 3 Series Manual

IMPORTANT NOTES
1. This product should be installed, commissioned and maintained by or under the supervision of a competent electrician
in accordance with current electrical engineering Codes of Practice, Regulations for the Electrical equipment of
Buildings (BS7671), CDM2007 - Construction (Design and Management) Regulations 2007, HSG150 - Health and
Safety in Construction, Statutory requirements and any Specific instruction issued by the Company.
2. After completing the installation and testing of this product it is essential that this leaflet is drawn to the attention of
the person responsible for its future operation and maintenance, and is at all times available for ready reference.
3. These notes assume throughout that the product is disconnected from the supply. It is essential that this is done
before any work is carried out.
4. These Panelboards are only designed for use with Eaton MCCBs. Failure to comply will result in invalid warranty and certification.
5. Operation of the incoming and outgoing devices should only be carried out by an instructed or skilled person.
Memshield 3 630/800A Panelboard/PanAssemblies
EPBN2863, EPBN21263, EPBN21863, EPBN3880, EPBN31240
EPBPN2863, EPBPN21263, EPBPN21863, EPBPN3880, EPBPN31240
Instruction leaflet LT1210 (12/19)
630A MCCB INCOMER FITTING
EPBKN2633 EPBKN2634
NOTE: When Top Fed, MCCB terminations must be reversed
800A MCCB INCOMER FITTING
EPBKN3803 EPBKN3804
Position
on Cover
14Nm
31Nm
31Nm
46Nm
Position
on Cover
14Nm
31Nm
630A DIRECT CABLE
INCOMER FITTING EPBKN263L
(FOR 630A PANELBOARDS ONLY)
MCCB INCOMING COVER
KNOCKOUT REMOVAL
DO NOT REMOVE FOR DIRECT
CABLE INCOMER
14Nm Remove for 4 Pole
Bottom Feed Incomer
Remove for 3 Pole
Top and Bottom
FeedIncomer
Remove for
4 Pole Top
FeedIncomer
The use to which this product is put and its place of installation is outside our control.
Particular care should therefore be taken to follow the instructions given here and to
ensure their continued availability in conjunction with the use of the product.
No responsibility can be accepted by us if these instructions are disregarded. Further
copies of these instructions and information concerning the installation and proper use
of this product can be obtained by contacting the:
TechnicalServicesDepartment
Eaton Electric Limited,
Middleton,
Manchester, M24 1GQ.
Tel: [phone],
email:[email protected]
www.eaton.com/recycling
LH OUTGOING CIRCUITS RH OUTGOING CIRCUITS
FED FROM:
INCOMING CABLE SIZE:
INSTALLATION DATE:
CONTRACTOR:
Warning -
Intellectual Property Rights
Eaton wishes to make it clear that it
owns intellectual property rights in the
product which it manufactures (whether
or not listed in this leaflet) and that it will
take legal action against any party
found to be manufacturing, using, or
selling any article which infringes the
company’s intellectual property.All
marks in this document identified with
an R symbol or a TM symbol adjacent
to the mark are trademarks of Eaton.
© 2019Eaton Electric Limited,
All rights reserved.
BOTTOM FEED
L1
LABEL FITTING Ensure all way labels are fitted in the correct places
Busbar
Way
Label
TOP FEED
Phase Label
Earth
Labels
Earth
Labels
L1
Cover Way
Labels Main Switch
Label
Cover Way
Labels Main Switch
Label
L1

CAT N0. A B C D E F G H J K
EPBPN2863 167 N/A 543.5 996 1052.5 1240 1291 177 96.75 601.5
EPBPN21263 167 N/A 724.5 1177 1233.5 1421 1472 267.5 187.25 692
EPBPN21863 167 438.5 996 1448.5 1505 1692 1743 403.25 323 828
EPBPN3880 167 N/A 580.5 1033 1089.5 1277 1328 177 96.75 638.5
EPBPN31280 167 N/A 761.5 1214 1270.5 1458 1509 222.25 142 794.5
OUTGOING MCCB & BLANK FITTING EPBN1BP1, EPBN2BP3, EPBN3BP3
Locate and click
A
B
C
D
E
COVER APERTURES
130 130
J
K
MCCB
Apertures
630/800A PAN ASSEMBLY DIMENSIONS
EPBPN2863, EPBPN21263, EPBPN21863, EPBPN3880, EPBPN31280
6Nm (Terminal Screw)
14Nm
(Terminal Screw)
19Nm
(Terminal Screw)
=
=
H
202.8
Min
Inside
Door 151
InsideCover
C
L
L
C
J
C
L
C
L
130
183.5
102
102
102
102
8
8
10.5
68.95 68.95
188.5 68.95 68.95 188.5
=
=
208.8
224.4
H
K
208.8
137 MCCB Apertures
137
68.95 68.95
188.5
=
=
130
183.5
208.8
224.4
J
102
8
L
C
L
C
H
K
MCCB
Apertures
EPBPN31280
EPBPN3880
Click into
Coveraperture
F
G
9
499
9
265
EPBPN2863, EPBPN21263, EPBPN21863
Remove for 4 Pole
Bottom Feed Incomer
Remove for 3 Pole
Top and Bottom
FeedIncomer
Remove for
4 Pole Top
FeedIncomer
225.2
83.1
IMPORTANT:
Fit MCCB with the adjustment
dial end towards the Busbar.
TOP FEED ADAPTOR FITTING
EPBKTFSLW
Prior to cabling, check pan
assembly alignment with
main cover
630/800A CABLE BOX, EXTENSION BOX, FILLER BOX AND DIN
ENCLOSURE FITTING
EPBN2183SXB, EPBN21863SXB
EPBN3EX250, EPBN2CX250, EPBN3EXDIN
3 POLE
4 POLE
NB - Provision to reposition Earth
Terminals in Cable Box
Boxfixing
Rotate Inner Cover
and Pan assembly
1800
Alternative Earth position
(both sides)
Main
Cover
TOP ENTRY
Panelboards are supplied
ready for bottom entry.
For top entry convert as
shownbelow.