Eaton MEMSHIELD 4 User manual

MEMSHIELD 4 INSTALLATION INSTRUCTIONS FOR
INCOMING AND OUTGOING METERING - 400A to 800A
Instruction leaflet LT1224 (01/19)
IMPORTANT NOTES
1. This product should be installed, commissioned and maintained by or under the supervision of a competent electrician in
accordance with current electrical engineering Codes of Practice, Requirements for the Electrical Installations (IET Wiring
Regulations BS7671), Construction (Design and Management) Regulations, HSG150 - Health and Safety in Construction, Statutory
requirements and any Specific instruction issued by the Company.
2. After completing the installation and testing of this product it is essential that this leaflet is drawn to the attention of the
person responsible for its future operation and maintenance, and is at all times available for ready reference.
3. These notes assume throughout that the product is disconnected from the supply. It is essential that this is done before any
work is carried out.
4. These Panelboards are only designed for use with Eaton MCCBs. Failure to comply will result in invalid warranty and
certification.
POWER SUPPLY TAP OFF FITTING EM4PBVT
Fit the DIN rail before mounting the fuse block.
For Incoming Meter Pack always fit the fuse block on the LH side,
otherwise the fuse block can be fitted on either side of the pan.
Feed the cables through the grommet and position to suit the
breakout in the top busbar removable shield. Replace the shield
and ensure the grommet is captured in the breakout.
INCOMING METER BOX ASSEMBLY - EM4PB250EXM AND METER
Incoming Meter Box can be fitted top or bottom.
CT in Pulse/Modbus
Power
In
Power
Out
Voltage
O/P
Voltage
I/P
N/L3
L2
L1 NL1 L2 L3
METER
Cable tidy Trunking
EM4PB250EXM
RJ45 CT
Connection
L3
L2
L1
L1
L2
L3
N
L1
L2
L3
L2
L1
N
L3
METER SETTINGS
Basic Meter Setup:- For detailed meter settings see Meter Operating Instructions.
Press: ”E “ for 3 seconds to toggle from Auto to Manual mode. (Stops screen scrolling).
IMPORTANT- Do NOT perform ‘Left Hand CT Mounting Phase Correction’ in Meter Operating Instructions.
The meter phases L1, L2 & L3 are setup for the CT to be mounted on both the RH and LH side of the board.
L1 L2 L3
Removable shield
breakout
Meter/CT Ratio Setup - The meter default CT setting is 160A. To
change the meter CT setting follow instructions below.
1. Press + keys together for 3 seconds to enter configuration menu.
2. To enter default password 1000 - Press then press . Press 4
times to move on and to enter CT primary page 04.
3. Press to select the digit to change and press or to raise or
lower the CT value. Set to 250, 400, or 800 to match CT.
4. Press to save settings and move on.
5. Press + keys together for 3 seconds to exit configuration menu.
METER TYPES
EPBMETER1 –Modbus/Pulse.
EMC3PP2P1 –Multi function MID with
Modbus/Pulse.
Note:
1. Ensure wire seal is fitted to MID Meter.
2. MID Meter will time out and lock, when
setting CT ratio, if meter setup instruction
are not followed.
Fuse block

800A INCOMER METER KIT FITTING - Refer to main installation leaflet LTXXXX for additional fitting details (EM4PBK804 and EM4PBK804L)
TOP ENTRY FITTING EM4PBK804M
CT needs to be moved from delivered position (shown shaded)
to position shown below.
NL1 L2 L3
NL1 L2 L3
800A LUGS INCOMER
FITTING EM4PBK804LM
TOP ENTRY FITTING EM4PBK404M
CT needs to be moved from delivered position (shown shaded)
to position shown below.
400A INCOMER METER KIT FITTING - Refer to main installation leaflet LTXXXX for additional fitting details (EM4PBK404 and EM4PBK404L)
NL1 L2 L3
NL1 L2 L3
400A LUGS INCOMER
FITTING EM4PBK404LM 400A MCCB INCOMER FITTING EM4PBK404M
NL1 L2 L3
NL1 L2 L3
EM4PB250EX
To Meter
To Meter 800A MCCB INCOMER FITTING EM4PBK804M
EM4PB250EX
31Nm
31Nm
31Nm
31Nm
31Nm
31Nm
31Nm
46Nm
46Nm
31Nm
46Nm
31Nm

OUTGOING METER ASSEMBLY - CT KIT FITTING
EPBCTMT160, EPBCTMT250 AND EPBCTMT400
OUTGOING METER CABLEWAYS
EM4PB68SXM, EPBN21240SXM,
EM4PB1214SXM, EM4PB1618SXM
CORNER FILLER - EM4PB300CX
POWER CABLE SETUP
Connect the power supply to the
Voltage I/P terminal of the first
outgoing meter. Loop the power
cable provided from the Voltage O/P
terminal to the Voltage I/P terminal
of the next meter.
Use extension EPBN3LKKTM to
connect the power from the LH side
meters to the meters on the RH side
cableway.
If required, 2 supplies can be fitted
to separately feed the LH and RH side
cableways.
Cable tie and Pad - across hinge.
Coil excess cable in trunking.
0.5m meter to meter
power lead
2.0m meter to CT
RJ45 CT lead
Cable tidy trunking.
Peel off the double sided
tape and fix where required
SINGLE POLE CT SPLITTER BOX EPBCTMT3P
The splitter box allows the separate phase monitoring
of a three phase CT on individual meters.
The CT can be fitted in the panelboard or cableway
for both group or compartmentailsed except in the
following instances:
- NZM3 CT must be fitted in the Cableway for
compartmentailsed form4 type6.
- Single pole CT must be fitted in the Cableway for
compartmentalised form4 type2 & 6
Ensure that P1 side of the CT is facing the MCCB.
Connect the RJ45 cable from the CT to the Meter.
Cable tie across hinge. Coil excess cable in trunking.
CT EXTENSION CABLE FITTING EPBN3LKRJ45
Use the RJ45 CT extension cable when fitting
a CT on the opposite side to the Cableway
/meter.
METERING ID LABELS
CT ID Label
Cable ID Label
Meter ID
Label
POWER EXTENSION CABLE EPBN3LKKTM
Power supply to the RH side Meter Cableway.
Route either across the bottom of the board
or up through the trunking and across the top
of the board.
Voltage O/P
Voltage I/P
Box fixing, ensure scratch washers
are fitted both sides
CABLEWAY EARTH
Provision to move
earth bar into
cableway, utilising
earth strap
P2
L3 L2 L1 RJ45 CT Connection
31Nm
15Nm

Warning -
Intellectual Property Rights
Eaton wishes to make it clear that it owns intellectual property rights in the
product which it manufactures (whether or not listed in this leaflet) and that it
will take legal action against any party found to be manufacturing, using, or
selling any article which infringes the company’s intellectual property. All
marks in this document identified with an R symbol or a TM symbol adjacent
to the mark are trademarks of Eaton.
© 2019 Eaton Electric Limited.
All rights reserved. www.eaton.com/recycling
The use to which this product is put and its place of installation is outside our
control. Particular care should therefore be taken to follow the instructions
given here and to ensure their continued availability in conjunction with the
use of the product.
No responsibility can be accepted by us if these instructions are disregarded.
Further copies of these instructions and information concerning the
installation and proper use of this product can be obtained by contacting the:
Technical Services Department
Eaton Electric Limited, Middleton, Manchester, M24 1GQ.
Tel: [phone],
email: techsup[email protected]
Connect the power supply to the
Voltage I/P terminal of the incomer
meter. Use extension EPBN3LKKTM to
connect from the Voltage O/P terminal
of the incomer meter to the Voltage I/P
terminal of the first outgoing meter.
Use the 0.5m power cable to connect
the power to the subsequent meters.
2.0m POWER CABLE EXTENSION
FITTING - EPBN3LKKTM
Use the extension cable to connect
power from the LH side meters to the
RH side cableway meters and for fitting
the incoming and outgoing metering
together.
The Top Meter extension box is not
required if the Incoming meter is fitted in
the side cableway.
SINGLE POLE CT OUTSIDE MCCB COMPARTMENTS
CT IN MCCB COMPARTMENT
The CT needs to be moved forward
on the mounting bracket to allow
room to sweep the RJ45 cable
through the exit point in the gland
plate.
General Note: Torque all M5 fixings to 3.8Nm Max.
The CT needs to be moved backward
on the mounting bracket (move the
fixing feet to opposite side) and
mounted the assembly in the
cableway at 45° to allow room for the
sweep of the live cables from the 3
single pole compartments.
Voltage O/P
Voltage I/P
To Incomer CT
First Outgoing CT
Voltage I/P
Incomer Meter
OUTGOING AND INCOMING METERING