Eaton NZM4-4-XKM1 Manual

Emergency On Call Service: Local representative (http://www.eaton.com/moeller/aftersales) or [phone] (de, en) 1/2
Electric current! Danger to life!
Only skilled or instructed persons may carry out the
following operations.
Lebensgefahr durch elektrischen Strom!
Nur Elektrofachkräfte und elektrotechnisch unterwiesene
Personen dürfen die im Folgenden beschriebenen Arbeiten
ausführen.
Tension électrique dangereuse !
Seules les personnes qualifiées et averties doivent
exécuter les travaux ci-après.
¡Corriente eléctrica! ¡Peligro de muerte!
El trabajo a continuación descrito debe ser realizado por
personas cualificadas y advertidas.
Tensione elettrica: Pericolo di morte!
Solo persone abilitate e qualificate possono eseguire le
operazioni di seguito riportate.
触电危险！
只允许专业人员和受过专业训练的人员进行
下列工作。
Электрический ток! Опасно для жизни!
Только специалисты или проинструктированные
лица могут выполнять следующие операции.
en
de
fr
es
it
zh
ru
Instruction Leaflet
Montageanweisung
Notice d’installation
Instrucciones de montaje
Istruzioni per il montaggio
安装说明
Инструкция по монтажу
11/10 IL01210011Z
(AWA1230-2039)
NZM4(-4)-XKM1, NZM4(-4)-XKM2, NZM4(-4)-XKM2S
Module Plate Connector Kits for NZM4 Molded Case Circuit Breakers and Switches
Caution!
The removal or exchange of parts during
mounting may become necessary.
Refer to installation instructions for proper
assembly and to maintain electrical
clearances.
¡Atención!
Con el fin de llevar a cabo los trabajos descritos, puede ser
necesario eliminar o cambiar alguna pieza.
Le rogamos tenga en cuenta todas las instrucciones de
instalación para así garantizar las líneas de fuga y efluvio
necesarias tras el montaje.
Attenzione!
Per l'esecuzione degli interventi descritti potrebbe essere
necessaria la rimozione o sostituzione di alcuni pezzi.
Attenersi alle istruzioni d'installazione per garantire dopo
l'assemblaggio le vie di dispersione necessarie.
Осторожно!
При проведении описанных процедур может
возникнуть необходимость демонтировать или
заменить детали.
Для обеспечения надлежащих зазоров и вывода тока
утечки, соблюдайте все инструкции по монтажу.
Vorsicht!
Für die Durchführung der beschriebenen Arbeiten
kann das Entfernen oder der Austausch von Teilen
notwendig sein.
Bitte alle Installations-Anweisungen beachten, um
die erforderlichen Luft- und Kriechstrecken nach dem
Zusammenbau zu gewährleisten.
Attention !
L’enlèvement où l’échange de certaines pièces
pendant le montage est parfois nécessaire.
Consultez l’instruction d’assemblage pour assurer
une installation conforme aux normes.
M10 metric size hardware, provided with all kits, connects to
double hole per phase configuration on NZM4 breaker or switch.
NZM4(-4)-XKM1
Single hole Module Plate Connector
M10 metric size
NZM4(-4)-XKM2
Double hole Module Plate Connector
M10 metric size
en
es
it
zh
ru
de
fr
1
2
3
1
4a
1
2
16 mm
50 Nm
(443 lb-in)
F32 mm
(F1.26”)
o10.5 mm
(o0.4”)
o10.5 mm
(o0.4”)
o10.5 mm
(o0.4”)
f500 mm (F20”)
F32 mm (F1.26”)
F32 mm (F1.26”)
F20 mm
(F0.79”)
F20 mm
(F0.79”)
F20 mm
(F0.79”)
F50 mm
(F2”)
F50 mm
(F2”)
F50 mm
(F2”)
F19 mm (F0.75”)
F19 mm (F0.75”)
F19 mm (F0.75”)
2 x(10 x50 x1) mm 2 x(50 x10) mm 1 x(120 – 300) mm
2 x(95 – 300) mm
1 x(250 – 600 kcmil)
2 x(AWG 3/0 – 600 kcmil)
4b
1
2
16 mm
50 Nm
(443 lb-in)
F32 mm
(F1.26”)
25
o10.5 mm
(o0.4”)
o10.5 mm
(o0.4”)
f500 mm (F20”)
F20 mm
(F0.79”)
F20 mm
(F0.79”)
F32 mm (F1.26”)
F15 mm (F0.59”)
F15 mm
(F0.59”)
F50 mm
(F2”)
F24 mm
(F0.9”)
2 x(50 x10) mm 2 x(95 – 185) mm
4 x(35 – 185) mm
2 x(AWG 3/0 – 350 kcmil)
4 x(AWG 2 – 350 kcmil)

2/2 Emergency On Call Service: Local representative (http://www.eaton.com/moeller/aftersales) or [phone] (de, en)
11/10 IL01210011Z
Eaton Industries GmbH, Hein-Moeller-Straße 7-11, 53115 Bonn, Germany
© 2002 by Eaton Industries GmbH, www.eaton.com/moeller/support All Rights Reserved
11/10 IL01210011Z 12255099/DE17 DHW/DM
Printed in Germany (01/11)
NZM4(-4)-XKM2S
Double hole Module Plate Connector
M12 metric size
+NZM4-XKP
1) Phase Barriers for use with Module Plate Connector kits
NZM4-XKM1
NZM4-XKM2
NZM4-XKM2S
+NZM4-XKSA
1) Terminal Cover for use with Module Plate Connector kits
NZM4-XKM1
NZM4-XKM2
NZM4-XKM2S
1) Use of either the NZM4-XKP Phase Barriers, or the
NZM4-XKSA Terminal Cover, is required at all times to
maintain proper electrical clearances when using any
of the NZM4-XKM... Module Plate Connector kits.
4c
1
2
16 mm
50 Nm
(443 lb-in)
F32 mm
(F1.26”)
F32 mm (F1.26”)
F32 mm (F1.26”)
F20 mm (F0.79”)
F20 mm (F0.79”)
F20 mm (F0.79”)
F20 mm
(F0.79”)
F20 mm
(F0.79”)
F20 mm
(F0.79”)
F50 mm
(F2”)
F50 mm
(F2”)
F50 mm
(F2”)
f500 mm (F20”)
f68 mm (F2.68”)
f68 mm (F2.68”)
o13.5 mm
(o0.53”)
o13.5 mm
(o0.53”)
o13.5 mm
(o0.53”)
2 x(10 x50 x1) mm 2 x(50 x10) mm 2 x(95 – 300) mm
2 x(AWG 3/0 – 600 kcmil)
5a
2
NZM4-XKP
Z 2
2 Nm
(17.7 lb-in)
4
3
5b
NZM4-XKSA
ON
Z 2
1 Nm
(9 lb-in) Z 2
2 Nm
(17.7 lb-in)
21
3