Eaton XV100 User manual

Manual
XV-102
Touch display
10/2020 MN04802004Z-EN

Touch display XV-102 10/2020 MN04802004Z-EN www.eaton.com
All brand and product names are trademarks or registered trademarks of the owner
concerned.
Emergency On Call Service
Please call your local representative:
Eaton.eu/aftersales
or
Hotline of the After Sales Service:
[phone] (de, en)
[e-mail]
Original instructions
The German-language edition of this document is the original operating manual.
1st edition 2014
see list of revisions, chapter „general“
© 2004 by Eaton Industries GmbH, 53105 Bonn
Editor: Antje Nonnen
All rights reserved, including those of the translation.
No part of this manual may be reproduced in any form (printed, photocopy, microfilm
or any other process) or processed, duplicated or distributed by means of electronic
systems without written permission of Eaton Industries GmbH, Bonn.
Subject to alteration without notice.

Content
Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com 1
Content
1 General........................................................................................ 5
1.1 List of revisions ............................................................................ 5
1.2 Purpose of these Operating manuals........................................... 5
1.3 Comments about this document ................................................. 5
1.4 Further reading............................................................................. 6
2 Description of device ................................................................. 7
2.1 Function ....................................................................................... 7
2.2 Intended use ................................................................................ 7
2.3 Device models ............................................................................. 7
2.4 Package contents......................................................................... 9
2.4.1 3.5" devices .................................................................................. 9
2.4.2 5.7" devices .................................................................................. 10
2.4.3 7.0" devices .................................................................................. 10
2.5 Accessory devices ....................................................................... 10
2.6 Marking ........................................................................................ 11
2.7 Marine approvals.......................................................................... 12
3 Safety regulations...................................................................... 13
3.1 Basics........................................................................................... 13
3.2 Precautionary statements ............................................................ 14
3.3 Mandatory requirements, personnel requirements ..................... 15
3.3.1 Occupational safety...................................................................... 15
3.3.2 Personnel qualifications ............................................................... 15
3.3.3 Operating manual......................................................................... 15
3.3.4 Installation, maintenance, and disposal........................................ 15
3.3.5 Prohibited use .............................................................................. 15
3.3.6 Prerequisites for proper operation ............................................... 16
3.4 Device-specific hazards................................................................ 17
4 Operating and indication elements.......................................... 21
4.1 Overview...................................................................................... 21
5 Installation .................................................................................. 23
5.1 Safety regulations ........................................................................ 23
5.2 Prerequisites for the location of use ............................................ 23
5.2.1 Engineering conditions of acceptability by
Underwriters Laboratories Inc. (UL) ............................................. 23
5.2.2 Conditions for marine approval (DNV GL) .................................... 23
5.2.3 Requirements for the mounting position ..................................... 24
5.3 Interfaces ..................................................................................... 25

Content
2Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com
5.3.1 Overview of interfaces................................................................. 26
5.3.2 Preparation of cables with D-Sub connector................................ 28
5.3.3 Power supply ............................................................................... 30
5.3.4 RS232 (System Port).................................................................... 32
5.3.5 Ethernet ....................................................................................... 33
5.3.6 USB device .................................................................................. 34
5.3.7 USB Host ..................................................................................... 34
5.3.8 SmartWire-DT Master.................................................................. 35
5.3.8.1 Additional documentation for devices with SmartWire-DT
Master interface..................................................................................... 35
5.3.8.2 Operating and indication elements of the SmartWire-DT
master interface..................................................................................... 36
5.3.8.3 POW/AUX (power supply for SmartWire-DT) ........................................ 37
5.3.8.4 SWD (SmartWire-DT interface).............................................................. 38
5.3.8.5 Commissioning the SmartWire-DT network .......................................... 39
5.3.9 CAN ............................................................................................. 41
5.3.10 Profibus........................................................................................ 44
5.3.11 RS485 .......................................................................................... 47
5.4 Mounting ..................................................................................... 49
5.4.1 Mounting the device.................................................................... 50
5.4.2 Screening the communication cables used ................................. 54
6 Operation.................................................................................... 55
6.1 Safety regulations ........................................................................ 55
6.2 Starting the device....................................................................... 56
6.3 Switch off the device................................................................... 56
6.4 Inserting and removing the SD card ............................................ 57
7 Maintenance and repairs........................................................... 59
7.1 Safety regulations ........................................................................ 59
7.2 Maintenance ................................................................................ 59
7.2.1 Cleaning the resistive touchscreen.............................................. 59
7.2.2 Recalibrating the resistive touchscreen ....................................... 59
7.2.3 Battery ......................................................................................... 59
7.3 Maintenance ................................................................................ 60
7.3.1 Repairs......................................................................................... 60
7.4 Troubleshooting ........................................................................... 61
8 Storage, transport and disposal............................................... 63
8.1 Safety regulations ........................................................................ 63
8.2 Storage ........................................................................................ 63
8.3 transport....................................................................................... 63
8.4 Disposal ....................................................................................... 64
9 Technical data ............................................................................ 65
9.1 Dimensions and weights ............................................................. 65

Content
Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com 3
9.1.1 3.5" devices .................................................................................. 65
9.1.2 5.7" devices .................................................................................. 66
9.1.3 7.0" devices .................................................................................. 67
9.2 Display.......................................................................................... 68
9.3 Touch sensor................................................................................ 68
9.4 System ......................................................................................... 69
9.5 Interfaces ..................................................................................... 70
9.5.1 Power supply ............................................................................... 71
9.5.2 SmartWire-DT Master .................................................................. 72
9.5.2.1 POW/AUX (power supply interface for SmartWire-DT) ......................... 72
9.5.2.2 SWD (SmartWire-DT interface).............................................................. 73
9.6 IP degrees of protection on the device ........................................ 74
9.7 Approvals and declarations .......................................................... 74
9.8 Applied standards and directives ................................................. 75
9.9 Environmental conditions............................................................. 76

Content
4Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com

1 General
1.1 List of revisions
Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com 5
1 General
1.1 List of revisions
The following table only lists major modifications.
1.2 Purpose of these Operating manuals
These Operating manuals contain the information required for the correct and safe use of the XV-102
touch display. The Operating manuals are part of the devices and must therefore be kept nearby.
These Operating manuals describe all aspects of the devices: transport, installation, commissioning,
operation, maintenance, storage and disposal. The operating system and the application software are
not described.
1.3 Comments about this document
Please send your comments, recommendations or suggestions about this document to
[email protected].
Publication date Page Keyword new modified
08/2016 Marine approval for the XV-102 series ✓
06/2018 74 Approval update ✓
07/2019 7Device models update ✓
10/2020 7Device models update ✓

Read Chapter 3 Safety regulations, 13, before working with the device. This contains
important information for your personal safety. This chapter must be read and under-
stood by all persons working with this device.
WARNING
Incomplete operator manual copies
Working with individual pages taken out from the operator manual may lead to bodily
injury and property damage due to missing safety information.
Always work with the complete document.

1 General
1.4 Further reading
6Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com
1.4 Further reading
Hardware
For more information on additional devices and modules, please refer to the following documentation:
Instructional leaflet IL048007ZU
Software
The following documents may also be helpful in relation to the use of this device:
Quick Start Guideline XV100 MN04802013Z
(commissioning the touch display, establishing communication with the programming PC and
creating projects with GALILEO and XSoft-CoDeSys-2)
System Description Windows CE MN05010007Z
(operation of the Windows CE operating system on touch displays)
Communication
In order to integrate your device into your system, additional communication settings will need to be
configured as appropriate for the PLC being used.
The following documents explain what needs to be taken into account and configured:
Networks in Brief MN05010009Z
(information on networks in general and on how to integrate PCs and touch displays in networks)
User Manual XSOFT-CODESYS 2 MN04802091Z, PLC programming
User Manual XSOFT-CODESYS 3 MN048008ZU, PLC programming
Tutorials
Helpful videos that explain how to use certain functions can be found on the corresponding product
pages on the Internet.
GALILEO Videos http://www.eaton.eu/GALILEO/#tabs-4
EasyE4 Tutorials http://www.eaton.eu/easy/#tabs-5
SmartWire-DT
SmartWire-DT The System Manual MN05006002Z
SmartWire-DT Module Manual IP20 MN05006001Z
SmartWire-DT Module Manual IP67 MN05006001Z
Download Center
Click on the Customer Support tab to get to the Download Center - Documentation page
http://www.eaton.eu/doc
Product pages
For the latest information on the product, please visit the Automation, Control & Visualization section at:
http://www.eaton.eu/xv
XV-102 as visualization of the device series easyE4: http://www.eaton.eu/easyE4
Eaton Online Catalog
http://www.eaton.eu/ecat
Enter "XV100" into the search box and the catalog will take you directly to the corresponding product
group in the Automation, Control and visualization section.

Documents relevant for the devices with SmartWire-DT Master interface, see Chapter
5.3.8 SmartWire-DT Master, 35.

2 Description of device
2.1 Function
Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com 7
2 Description of device
2.1 Function
Touch displays XV-102 can be used as HMI devices or as integrated HMI/PLC devices.
2.2 Intended use
Touch displays XV-102 are primarily intended for use in machine and system building applications.
They are intended exclusively for monitoring, operating, and controlling machines and systems. Any
other use must be discussed and agreed upon with the manufacturer in advance.
2.3 Device models
The following versions of touch displays XV-102 are available:
Fig.. 1 XV-102 3.5" Fig.. 2 XV-102 5.7"
Fig.. 3 XV-102 7,0" Fig.. 4 XV-102 design for easyE4

2 Description of device
2.3 Device models
8Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com
Basic features Display Communication interfaces XV-102 part no.
Version A:
1 Slot for 1 SD-card
Integrated interfaces:
1Ethernet 100/10
1USB Device
Communication interfaces
Resistive touch,
3.5" TFT-LCD, 32 gray levels,
QVGA
– XV-102-A0-35MQR…
Profibus XV-102-A2-35MQR…
RS232 XV-102-A3-35MQR…
RS485 XV-102-A4-35MQR…
CAN and RS232 XV-102-A5-35MQR…
Resistive touch,
3.5" TFT-LCD, 32 gray levels,
QVGA
– XV-102-A0-35TQR…
Resistive touch,
5.7" TFT-LCD, 32 gray levels,
VGA
– XV-102-A3-57TVR…
Version B:
1 Slot for 1 SD-card
Integrated interfaces:
1Ethernet 100/10
1USB Device
Communication interfaces
Resistive touch,
3.5" TFT-LCD, 32 gray levels,
QVGA
– XV-102-B0-35MQR…
RS232 XV-102-B3-35MQR…
RS485 XV-102-B4-35MQR…
CAN and RS232 XV-102-B5-35MQR…
CAN and RS485 XV-102-B6-35MQR…
Profibus and RS485 XV-102-B8-35MQR…
Resistive touch,
3.5" TFT-LCD, 64K colors,
QVGA
– XV-102-B0-35TQR…
Profibus XV-102-B2-35TQR…
RS232 XV-102-B3-35TQR…
RS485 XV-102-B4-35TQR…
CAN and RS232 XV-102-B5-35TQR…
CAN and RS485 XV-102-B6-35TQR…
Profibus and RS485 XV-102-B8-35TQR…
SmartWire-DT Master XV-102-BE-35TQR…
Version D:
1 Slot for 1 SD-card
Integrated interfaces:
1Ethernet 100/10
1USB Device
1USB host
Communication interfaces
Resistive touch,
5.7" TFT-LCD, 64K colors,
VGA
RS232 XV-102-D0-57TVR…
RS485 and RS232 XV-102-D4-57TVR…
CAN, RS485 and RS232 XV-102-D6-57TVR…
Profibus, RS485 and RS232 XV-102-D8-57TVR…
Resistive touch,
7.0" TFT-LCD, 64K colors,
WVGA
RS232 XV-102-D0-70TWR…
RS485 and RS232 XV-102-D4-70TWR…
CAN, RS485 and RS232 XV-102-D6-70TWR…
Profibus, RS485 and RS232 XV-102-D8-70TWR…

2 Description of device
2.4 Package contents
Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com 9
Tab. 1 Device models
2.4 Package contents
The accessories supplied with the XV-102 touch display depend on the size of the device.
2.4.1 3.5" devices
Tab. 2 Package contents for 3.5" devices
Version E:
1 Slot for 1 SD-card
Integrated interfaces:
1Ethernet 100/10
1USB Device
1USB host
Communication interfaces
Resistive touch,
5.7" TFT-LCD, 64K colors,
VGA
CAN, RS485 and SmartWire-DT master XV-102-E6-57TVR…
Profibus, RS485 and SmartWire-DT master XV-102-E8-57TVR…
Resistive touch,
7.0" TFT-LCD, 64K colors,
WVGA
CAN, RS485 and SmartWire-DT master XV-102-E6-70TWR…
Profibus, RS485 and SmartWire-DT master XV-102-E8-70TWR…
Version H:
1 Slot for 1 SD-card
Integrated interfaces:
1Ethernet 100/10
1USB Device
1 USB-Host (only 5.7" and
7.0" devices)
Communication interfaces
Resistive touch,
3.5" TFT-LCD, 64K colors,
QVGA
RS232 XV-102-H3-35TQR…
RS485 XV-102-H4-35TQR…
Resistive touch,
5.7" TFT-LCD, 64K colors,
VGA
RS232 XV-102-H3-57TVR…
RS485 XV-102-H4-57TVR…
Resistive touch,
7.0" TFT-LCD, 64K colors,
WVGA
RS232 XV-102-H3-70TWR…
RS485 XV-102-H4-70TWR…
Basic features Display Communication interfaces XV-102 part no.

If necessary, you can order stylus pens in groups of ten (ACCESSORIES-TP-PEN-10, ar-
ticle no. 139808), as well as other accessories. Please contact the supplier.
Number Description
1 Touch display:
XV-102-…-35MQR… or
XV-102-…-35TQR…
4 Mounting brackets with grub screw for flush mounting
1 Sealing strip for mounting the device (glued in the device and/or loose enclosed)
1 Power supply connector for the device
1 Power supply connector for SmartWire-DT Master (only supplied with XV-102-BE-…-
devices)

2 Description of device
2.5 Accessory devices
10 Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com
2.4.2 5.7" devices
Tab. 3 Package contents for 5.7" devices
2.4.3 7.0" devices
Tab. 4 Package contents for 7.0" devices
2.5 Accessory devices
Different accessories are available. Only use original accessories.
Number Description
1 Touch display:
XV-102-…-57TVR…
6 Mounting brackets with grub screw for flush mounting
1 Sealing strip for mounting the device (glued in the device and/or loose enclosed)
1 Power supply connector for the device
1 Power supply connector for SmartWire-DT Master (only supplied with XV-102-E…-
devices)
Number Description
1 Touch display:
XV-102-…-70TWR…
8 Mounting brackets with grub screw for flush mounting
1 Sealing strip for mounting the device (glued in the device and/or loose enclosed)
1 Power supply connector for the device
1 Power supply connector for SmartWire-DT Master (only supplied with XV-102-E…-
devices)

Order the accessories required from your supplier.

2 Description of device
2.6 Marking
Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com 11
2.6 Marking
Nameplate The device has a nameplate on rear. This nameplate makes it possible to identify the device and
includes the following information:
Manufacturer address
Part no.
Power supply required
Article No. (part No. or article No.)
Serial No.
Date of manufacture (week/year)
Certification marks and information concerning the corresponding certifications/approvals
Layout of ports/interfaces and controls
Permissible mounting options (top edge «Top»)
Support To get fast and effective support, make sure to always provide Customer Service with the following
information from the nameplate:
Article No. (part No. or article No.)
Serial No.

2 Description of device
2.7 Marine approvals
12 Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com
2.7 Marine approvals
Obtained type approvals
The touch displays HMI/PLC XV-102 have been granted the required shipping classification by Det
Norsk Veritas / Germanischer Lloyd (DNV GL)
DNVGL-CG-0339 type approval, November 2015 edition,
"Environmental test specification for electrical, electronic and programmable equipment and
systems"
Certificate No.: TAA00000NC
Location classes
Installation restrictions
Installation and commissioning as indicated in the documentation for the touch display
Screened communication cables improve EMC behavior
PE connection of communication cables improve EMC behavior
(e.g. earth-connection kit: EATON ZB4-102-KS1)
Temperature B - Ambient air temperature: 0°C to +55°C
Humidity
B - Relative humidity up to 100 % at all relevant temperatures.
Vibration A - Bulkheads, beams, deck, bridge, Acceleration amplitude: 0.7 g
EMC B* - All locations (including bridge and open deck)
Input Required protection according to DNV-GL Rules shall be provided upon
installation on board
* Filters / Ferrites maybe required to fulfil. See installation restrictions
Location class interface Installation
EMC B
Power
supply Place interference filter
Ethernet
Place the ferrite core or snap-together ferrites at a max.
distance of 20 cm from the external device plug.
SWD
communication
SWD power
supply
RS485
RS232

5.2.2 Conditions for marine approval (DNV GL), 23
5.3.3 Section Radio interference suppression filter for the 24 V DC supply,
31
5.4.2 Screening the communication cables used, 54

3 Safety regulations
3.1 Bas ics
Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com 13
3 Safety regulations
3.1 Basics
The device has been designed according to the state of the art and all generally accepted safety rules
and standards. However, this alone cannot eliminate all potential hazards, which is why it is necessary
for you to be aware of all hazards and residual risks.
Do not run the device unless it is in perfect technical condition. Make sure to always operate it as spec-
ified in this document.

Read this chapter before working with the device. This contains important information
for your personal safety. This chapter must be read and understood by all persons work-
ing with this device.

3 Safety regulations
3.2 Precautionary statements
14 Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com
3.2 Precautionary statements
The following symbols are used in this document according to the hazard level described:
The hazard symbol used and the corresponding text will provide information regarding the specific
hazard and how to avoid or prevent it.
DANGER
DANGER signal word
Indicates an imminent hazardous situation that will result in death or serious injury if
it is not avoided.
WARNING
WARNING signal word
Indicates a potentially hazardous situation that could result in death or serious injury
if it is not avoided.
CAUTION
CAUTION signal word
Indicates a potentially hazardous situation that could result in minor or moderate in-
jury if it is not avoided.
CAUTION
CAUTION signal word without warning sign
Indicates a situation that could result in property damage if it is not avoided.

Used to highlight useful information.

3 Safety regulations
3.3 Mandatory requirements, personnel requirements
Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com 15
3.3 Mandatory requirements, personnel requirements
3.3.1 Occupational safety
All generally accepted occupational health and safety rules and standards (internal and national) must
be complied with.
3.3.2 Personnel qualifications
The personnel responsible for installation, operation, maintenance, and repairs must have the neces-
sary qualifications for the work they will be performing. They must be appropriately trained and/or
briefed and be informed of all hazards and risks associated with the device.
3.3.3 Operating manual
It must be ensured that any person working with the device in any phase of its lifespan has read and
understood the relevant sections of the Operating manuals.
3.3.4 Installation, maintenance, and disposal
Make sure that the device is connected, installed, serviced, and disposed of professionally and in line
with all relevant standards and safety rules.
3.3.5 Prohibited use
The implementation of safety functions (relating to the protection of personnel and machinery) using the
device is prohibited.
WARNING
Incomplete operator manual copies
Working with individual pages taken out from the operator manual may lead to bodily
injury and property damage due to missing safety information.
Always work with the complete document.

3 Safety regulations
3.3 Mandatory requirements, personnel requirements
16 Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com
3.3.6 Prerequisites for proper operation
In order for the device to be able to meet the contractually stipulated terms, the following must be
observed:
Only qualified personnel should be allowed to work with the device.
These persons must have read the Operating manuals and must observe the requirements
described.
The ambient conditions stated must be observed. See chapter 9.9 Environmental conditions, 76
Maintenance work must be carried out correctly.
Potentially explosive atmosphere, Zone 22:
The ground resistance of accessible metal parts must be less than 109ohms.
We assume no liability for damages, consequential damages, and/or accidents caused by the following:
Failure to follow occupational health and safety rules and standards
Device failures or function disturbances
Improper use and/or handling
Failure to observe the Operating manuals
Alterations, changes, and repairs to the device

Repairs, see Chapter 7.3.1 Repairs, 60.

3 Safety regulations
3.4 Device-specific hazards
Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com 17
3.4 Device-specific hazards
DANGER
Explosion hazard
Death, serious injury, and property damage may occur if the device is being used in
a potentially explosive (classified) location and, during operation, an electrical plug-
in connection is disconnected or the device is exposed to dangerous impacts or oth-
er types of dangerous mechanical shock.
Use the device in the following environments only:
-Non-hazardous (non-explosive) areas
-Potentially explosive atmosphere, Zone 22 (according to ATEX 94/9/EC)
Potentially explosive atmosphere, Zone 22:
The ground resistance of accessible metal parts must be less than 109ohms.
When used in a potentially explosive atmosphere, Zone 22, the environment has
to be designed to avoid any bunch discharge
Make sure that the device is not exposed to dangerous impacts and other types
of dangerous mechanical shock.
Do not operate the device in hazardous (classified) locations unless it is mounted
correctly.
De-energize the device before disconnecting plug connections.
WARNING
Live parts inside the device
When the device is open, there will be an electric shock hazard if live parts are
touched.
The device must not be opened.
WARNING
Stray currents
Large transient currents between the protective circuits of different devices may re-
sult in fire or in malfunctions due to signal interference.
If necessary, a potential equalization conductor should be installed parallel to the
cable. This should have a cross-section that is a multiple of the cable screen.
CAUTION
Electrostatic discharge
Electrostatic discharge may damage or destroy electronic components.
Avoid contact with components (such as connector pins) that are susceptible to
electrostatic discharge.
Discharge (by touching a grounded metal object) any static charge accumulated
in your body before touching the device.

3 Safety regulations
3.4 Device-specific hazards
18 Touch display XV-102 10/2020 MN04802004Z-EN Eaton.com
CAUTION
Non-galvanically-isolated interfaces
The device may be damaged by potential differences.
The GND terminals of all bus modules must be connected.
CAUTION
Sensitive resistive touch surface
Damage to the resistive touch due to the use of pointed or sharp objects.
Only activate the resistive touch with your finger or a stylus.
When wearing gloves, ensure that these are clean. They must not be covered
with abrasive dust or sharp particles.
CAUTION
Data loss
During a write operation, the SD card may lose data or may be destroyed if it is re-
moved or if there is a power failure.
Insert the SD card only when the device is de-energized.
Avoid writing to SD cards as much as possible. Reasons:
-SD cards have a limited number of write cycles.
-If there is a voltage drop while a write operation is in progress, data loss is
highly likely to occur.
Remove the SD card only when the device is de-energized.
Before switching off, ensure that no software write operations to the SD card are
in progress.
CAUTION
Condensation in/on the device
If the device is or was exposed to climatic changes (temperature fluctuation, air hu-
midity) moisture can form on or in the device (device condensation). In this case,
there is a risk of short-circuit.
The device must not be switched on when device condensation is present.
If the device has condensation in or on it, or if the device has been exposed to
temperature fluctuations, let the device settle into the existing ambient air tem-
perature before switching it on (do not expose the device to direct thermal radia-
tion from heating appliances).