Eaton 5P750RC User manual

Page 1
ENGISH
Copyright © 2015 EATON
All right s reserved.
5P 750VA -1. 5 KVA EU_EN
Installation and
user manual
5P750RC
5P1000RC
5P1500RC

Page 2
5P 750VA-1.5 KVA US_EN
Certification Standards
Unint errupt ible power syst ems (UPS) direct ives:
•IEC 62040-1: General and saf et y requirement s f or UPS
•IEC 62040-2: Elect romagnet ic compat ibilit y (EMC) requirement s
•IEC 62040-3: Met hod of specifying t he perf ormance and t est requirement s
. IEC 62040-4: Environment al aspect s - Requirement s and report ing
CE mark
CE compliance cont act : Eat on I.F. – 110 rue Bl aise Pascal – 38330 Mont bonnot Saint Mart in - France
The EC Decl arat ion of Conf ormi t y i s avail abl e upon request f or pr oduct s w it h a CE mark.
For copies of t he EC Declarat ion of Conf ormit y, cont act Eat on Power Qualit y or check Eaton websit e:
www. powerqualit y. eat on. com
Class B emission l evel CISPR 22(EN 55022)
Harmonics emission: IEC 61000-3-2
Fl ickers emission: IEC 61000-3-3
FCC 47 CFR Part 15, Subpart B - Unint ent ional Radiat ors Cl ass B
Special symbols
The f oll owing are examples of symbol s used on t he UPS or accessories t o alert you t o import ant
inf or mat i on:
RISK OF ELECTRIC SHOCK - Observe t he warning associ at ed wit h t he risk of elect ric shock symbol.
Import ant inst ruct ions t hat must always be f ollowed.
Do not discard t he UPS or t he UPS bat t eries in t he t rash.
This product cont ains sealed lead acid bat t eries and must be disposed as it 's explain in t his manual.
For more inf or mat i on, cont act your local r ecycl ing/ reuse or hazardous wast e cent er.
This symbol indicat es t hat you should not discard wast e elect rical or elect ronic equipment (WEEE)
in t he t rash. For proper disposal, cont act your l ocal recycling/ reuse or hazardous wast e cent er.
Inf or mat i on, advi ce, help.

Page 4
5P 750VA-1.5 KVA US_EN
Safety of Persons
Product Safety
Special Precautions
•The syst em has it s own power source (t he bat t ery). Consequent ly, t he power out let s may be energized
even if t he syst ems is disconnect ed f rom t he AC power source.
•Dangerous vol t age levels are present wit hin t he syst em. It should be opened exclusively by qualif ied
service personnel .
•The syst em must be plugged t o an eart hed out let .
•The bat t ery supplied wit h t he syst em cont ains smal l amount s of t oxic mat erial s.
To avoid accident s, t he directives list ed below must be observed:
-servicing of bat t eri es shoul d be perf ormed or super vi sed by personnel knowledgeable about bat t eries
and t he required precaut ions.
-when replacing bat t eries, replace wit h t he same t ype and number of bat t eries or bat t ery packs.
-do not di spose of bat t eries in a f ire. The bat t eries may explode.
-bat t eries const it ut e a danger (el ect rical shock, burns). The short -circuit current may be very high.
Precaut ions must be t aken f or all handling:
•Wear rubber gloves and boot s.
•Do not lay t ools or met al part s on t op of bat t eries.
•Disconnect charging source prior t o connect ing or disconnect ing bat t ery t erminals.
•The UPS connect ion inst ruct ions and operat ion described in t he manual must be f ollowed in t he indicat ed
order.
•A prot ect ion circuit breaker must be inst all ed upst ream and be easily accessibl e. The syst em can be
disconnect ed f r om t he AC power sour ce by unplugging t he input cable.
•Check t hat t he indicat ions on t he rat ing plat e correspond t o your AC powered syst em and t o t he act ual
elect rical consumpt ion of al l t he equipment t o be connect ed t o t he syst em.
•For PLUGGABLE EQUIPMENT, t he socket -out l et shall be inst alled near t he equipment and shall be easily
accessible
•Never inst all t he syst em near l iquids or in an excessively damp environment .
•Never l et a f or eign body penet rat e inside t he syst em.
•Never block t he vent ilat ion grat es of t he syst em.
•Never expose t he syst em t o direct sunlight or source of heat .
•If t he syst em must be st ored prior t o inst al lat ion, st orage must be in a dry place.
•The admissible st orage t emperat ure range is -15 t o +50 ° C / 5 t o 122 ° F.
•The syst em is not f or use in a comput er r oom.
•All handling operations will require at least two people (unpacking, installation in rack syst em).
•Bef ore and af t er t he inst all at ion, if t he UPS remains de-energized f or a long period, t he UPS must be
energized for a period of 24 hours, at least once every 6 mont hs (for a normal st orage t emperat ure less
t han 25 ° C / 77 ° F). This charges t he bat t ery, t hus avoiding possible irreversible damage.
•During t he replacement of t he Bat t ery Modul e, it is imperat ive t o use t he same t ype and number of
element as t he original Bat t ery Modul e provided wit h t he UPS t o maint ain an ident ical level of
perf ormance and saf et y. In case of doubt , don't hesit at e t o cont act your EATON represent at ive.

Page 4
5P 750VA-1.5 KVA US_EN
1. Introduction . . .. . . . . .. . . . .. . . . . .. . . . .. . . . .. . . . . . .. . . . .. . . . .. . . . . .. . . . .. . . . . . .. . . . .. . . . .. . . . . . 5
1. 1 Environment al prot ect ion . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . . 5
2. Presentation . .. . . . . .. . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . .. . . . . . .. . . . .. . . . .. . 6
2. 1 St andar d i nst al lat i ons. . .. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. 6
2. 2 Rear panel . . . . . . . .. . . . . .. . . . .. . . . .. . . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . . .. . . . .. . . . . .. . . 7
2. 3 Cont rol panel . . . . . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . . . .. . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . .. 8
2. 4 LCD descript ion . . . . .. . . . . .. . . . . .. . . . .. . . . .. . . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . . .. . . . . 9
2. 6 User set t ings. . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . . .. . . . .. . . . . .. . . . .. . . . .. . . . . .. . . . . .. . . . . .. . 10
3. Installation . . .. . .. . .. . . .. . .. . .. . . .. . .. . . .. . .. . .. . . .. . .. . .. . . .. . .. . .. . . .. . .. . . . .. . .. . .. . . .. . 12
3. 1 Unpacking and cont ent s check . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . . .. . . . .. . . . . .. . . . 12
3. 2 Bat t ery module connect ion . .. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . 13
3. 3 Rack inst allat ion . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . 14
3. 4 Wall mount i ng of rack model . .. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . 15
3. 5 Communicat ion port s . . . . .. . . . . .. . . . .. . . . .. . . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . 16
4. Operation . .. . . .. . .. . .. . . .. . .. . .. . . .. . .. . .. . . .. . .. . . .. . .. . .. . . .. . .. . .. . . .. . . .. . . .. . .. . .. . . .. 17
4. 1 St art -up and Normal operat ion . . .. . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . . .. . . . .. . . . . .. . . . . 17
4. 2 St art ing t he UPS on Bat t ery . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . . .. . . . .. . . . . .. . . . .. . . . . .. 17
4. 3 UPS Shut down . . .. . .. . . .. . .. . .. . . .. . .. . . .. . .. . . .. . .. . .. . . .. . .. . . .. . .. . . .. . .. . . .. . . .. . .. 17
4. 4 Operat ion on Bat t ery Power . . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . . 17
4. 5 Ret urn of AC Input Power . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . 18
4. 6 UPS remot e cont rol f unct ions.. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . 18
5. Maintenance . . . .. . . . . .. . . . .. . . . .. . . . . .. . . . .. . . . . . .. . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . . .. . . 19
5. 1 Tr oubleshoot i ng. . . . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . . .. . . . .. 19
5. 2 Bat t ery-module replacement . . . . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . . .. . . . .. . . . . .. . . . .. . 20
6. Appendices . . .. . . .. . .. . . .. . .. . .. . . .. . .. . .. . . .. . .. . . .. . .. . .. . . .. . .. . .. . . .. . . .. . .. . . .. . .. . . .. 21
6. 1 Technical speci f icat ions ... .. .. .. .. .. .. .. .. ..... .. .. .. .. .. .. .. .. ..... .. .. .. .. .. .. .. .. 21
6. 2 Gl ossary .. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . .. 22

Page 4
5P 750VA-1.5 KVA US_EN
1. Introduction
Thank you f or sel ect ing an EATON product t o prot ect your elect rical equipment .
The 5P range has been designed wit h t he ut most care.
We recommend t hat you t ake t he t ime t o read t his manual t o t ake f ull advant age of t he many f eat ur es of your
UPS (Unint errupt ible Power Syst em).
Bef or e inst al li ng your 5P, please read t he booklet present ing t he saf et y inst ruct ions. Then
f ol low t he i ndicat ions in t his manual .
To discover t he ent ire range of EATON product s and t he opt ions avai lable f or t he 5P range, we invit e you t o visit our
web sit e at www.eat on.com/ powerqualit y or cont act your EATON represent at ive.
1.1 Environmental protection
EATON has implement ed an environment al-prot ect ion policy. Product s
are developed according t o an eco-design approach.
Substances
This product does not cont ain CFCs, HCFCs or asbest os.
Packing
To improve wast e t reat ment and f acilit at e recycling, separat e t he various packing component s.
•The cardboard we use comprises over 50%of recycled cardboard.
•Sacks and bags are made of polyet hylene.
•Packing mat erial s are recycl able and bear t he appropriat e ident ificat ion symbol 01
PET
Materials Abbreviations Number in 01
the symbols PET
Pol yet hylene t erepht halat e PET 01
High-densit y polyet hylene HDPE 02
Pol yvinyl chloride PVC 03
Low-densit y polyet hylene LDPE 04
Pol ypropylene PP 05
Polyst yrene PS 06
Follow all local regulat ions f or t he disposal of packing mat erial s.
End of life
EATON will process product s at t he end of t heir service lif e in compliance wit h local regulat ions. EATON
works wit h companies in charge of coll ect ing and eliminat ing our product s at t he end of t heir service l if e.
Product
The product is made up of recyclable mat erials.
Dismant l ing and dest ruct ion must t ake place in compliance wit h all local regulat ions concerning wast e. At t he end
of it s service lif e, t he product must be t ransport ed t o a processing cent er f or elect rical and elect ronic wast e.
Battery
The product cont ains lead-aci d bat t eries t hat must be processed according t o applicable local regulat ions
concerning bat t eries.
The bat t ery may be removed t o compl y wit h regulat ions and in view of correct disposa

Page 6
5P 750VA-1.5 KVA US_EN
2. Presentation
2. 1 Standard installations
Rack model
Description Weights
(kg/lb)
Dimensions (mm/inch)
D x W x H
5P750RC 14. 1/ 31. 1 370*440*86. 2 / 14.6*17. 3*3. 4
5P1000RC 15. 0/ 33.1 370*440*86. 2 / 14.6*17. 3*3. 4
5P1500RC 18. 4/ 45.5 370*440*86. 2 / 14.6*17. 3*3. 4
D
W
H

Page 7
5P 750VA-1.5 KVA US_EN
2.2 Rear panel
5P750RC & 5P1000RC & 5P1500RC
1)
At t ached 1. 8 m input power cord f or AC
power source
2) Sl ot f or opt ional communicat ion card
3) Primary group : Out let s f or connect ion
of crit ical equipment
4) Group 1: programmable out let s for
connect ion of equipment
5) Group 2: programmable out let s for
connect ion of equipment
6) RS232 communicat ion port
7) USB communicat ion port
8) Connect or f or ROO (remot e ON/ OFF) or
RPO (Remot e Power Of f ) cont r ol
①
②
③
④
⑥
⑦
⑧
⑤

Page 8
5P 750VA-1.5 KVA US_EN
ENGLISH
2.3 Control panel
The UPS has a five-button graphical LCD. It provides useful information about the UPS itself, load status,
events, measurements and settings.
100%
19min
1EBM
The f ollowing t abl e shows t he indicat or st at us and descript ion:
Indicator
Status
Description
Gree
n
On
The UPS is operat ing normally
Orange
On
The
UPS is on Bat t ery mode.
R
ed
On
The
UPS has an act ive alarm or faul t . See t rouble- shoot ing in
sect ion 5. 1
f or addit ional inf or mat i on.

Page 9
5P 750VA-1.5 KVA US_EN
2.4 LCD description
As def ault , or af t er 5 minut es of inact ivit y, t he LCD displ ays t he screen saver.
The backlight LCD aut omat ically dims af t er 10 mi nut es of inact ivit y. Press any but t on t o rest ore t he screen.
The f ollowing t able describes t he st at us inf ormat ion provided by t he UPS
Note: If ot her indicat or appears, see t roubleshoot ing on sect ion 5. 1 f or addi t ional inf ormat i on.
Operation status Cause Description
St andby mode
The UPS is Off, wait ing f or st art - up
command f rom user.
Equipment is not powered unt il
but t on is pressed.
Online mode
The UPS is operat ing normally.
The UPS is powering and prot ect ing
t he equipment .
In AVR mode
1
beep every 10 seconds
The UPS is operat ing normally but
t he ut ilit y vol t age is out side
normal mode t hresholds.
The UPS is powering t he equipment
t hrough a Aut omat ic Volt age
Regul at ion device.
The equipment is st il l normally
prot ect ed.
On Bat t ery
Bat t ery LED is on
1 beep every 10 seconds
A ut ili t y f ail ur e has occur red and
t he UPS is in Bat t ery mode.
The UPS is powering the equipment
with the battery power. Prepar
e your
equipment for shutdown.
End of backup t ime
1 beep every 3 seconds
The UPS is in bat t ery mode and
t he bat t ery is running low.
This warning is approximat e, and
t he act ual t ime t o shut down may
vary si gnif icant l y.
Depending on t he UPS Load, t he
"Bat t ery Low" warning may occur
bef ore t he bat t ery reaches 20 %
capacit y.

Page 10
5P 750VA-1.5 KVA US_EN
ENGLISH
2.5 Display functions
Press t he Ent er () but t on t o act ivat e t he menu opt ions. Use t he t wo middle but t ons ( and ) t o scroll t hrough t he
menu st ruct ure. Press t he Ent er ( ) but t on t o select an opt ion. Press t he but t on t o cancel or ret urn t o t he
previous menu.
Main menu
Submenu
Display information or Menu function
Measurement s
Load W VA / Load A pf / Out put V Hz / Input V Hz /
Bat t ery V mi n / Ef ficiency / Power usage
Cont rol
Load Segment s
Group 1: ON / OFF
Group 2: ON / OFF
These commands overrule user set t ings for load segment s.
St art bat t ery t est
St art s a manual bat t ery t est
Reset fault st at e
Clears act ive f aul t s
Rest ore fact ory set t ings Ret urns all set t ings t o original values (UPSrest art required)
Reset power usage
Clears power usage measurement s
Set t ings
Local set t ings
Set s product general paramet ers
In/ Out set t ings
Set s Input and Out put paramet er s
On/ Of f set t ings
Set s On/ Of f condit ions
Bat t ery set t ings
Set s bat t ery conf igurat i on
Fault log
Fault list
Displays t he f ault s st ored
Reset f ault l ist
Cl ears fault s
Ident if icat i on
UPS Type / Part Number / Serial Number / Firmware release /
Com card address
2.6 User settings
The f oll owing t able displays t he opt ions t hat can be changed by t he user.
Submenu
Available settings
Default settings
Local settings
Language
[English] [Français] [ Deut sch] [ Español]
[Русский] [Port uguês] [It aliano]
[Simpl if ied Chinese] [Japanese]
Menus, st at us, not ices and al arms, UPS
f ault , Event Log dat a and set t ings are in
all support ed languages.
[English]
User sel ect able when UPS is
power ed for t he f irst t ime.
LCD set t ings
Modi f y LCD screen bright ness and
cont rast t o adapt t o room light
condit ions .
Audible alarm
[ Enabled] [ Disabl ed on bat t ery]
[ Al ways disabl ed]
Enable or disable t he buzzer if an
alarm occurs.
Enable
In/Out settings
Output voltage
[100V] [120V] [ 125V]
User select able when UPS
is powered for t he first t ime
Input thresholds
[ Normal mode] [ Ext ended mode]
Ext ended mode reduces lower
input vol t age t o 150 V bef or e UPS
t ransf ers t o bat t er y.
Normal mode
Sensitivity
[High] [ Low]
High: for sensit ive equipment , UPS will
easil y t ransf er t o bat t ery when ut ilit y
condit ions ar e becoming bad.
High
Load segments -
Auto start delay
[No Delay] [ 1 s] [ 2 s] … [ 65354 s] The
connect ed l oad is powered aft er t he
specified delay.
Gr oup 1: 3 s
Gr oup 2: 6 s
Load segments
-
Auto shutdown
delay
[Disable] [ 0s] [ 1 s] [2 s] …[65354 s]
During a power out age, aut hor ises
t o keep some equipment running
while t urning of f ot her equipment .
Group 1: Disable
Group 2: Disable
Overload prealarm
[10 %] [15 %] [20 %] . . . [ 100 %]
[105 %]
Gives a warning when a predef ined
cr it ical percent age of l oad is
[105 %]

Page 11
5P 750VA-1.5 KVA US_EN
ENGLISH
Submenu
Available settings
Default settings
On/Off settings
Col d st art
[Disable] [Enable]
Enables the product to be started
on battery power.
First cold start always disabled.
Enable
For ced reboot
[Disable] [Enable]
If mains recover during a shutdown
sequence:
- if enabled, shutdown sequence will
complete and wait 10 seconds prior
to restart
- if disabled, shutdown sequence will
not complete and restart will occur
immediately.
Enable
Aut o r est art
[Disable] [ Enable]
Enabl es t he product t o rest art
aut omat ical ly when mains recovers
af t er a compl et e bat t ery discharge.
Enable
Energy saving
[Disable] [ Enable]
If enabled, UPS will shut down af t er
5min of back-up t ime, if no load is
det ect ed on t he out put .
Disable
Sl eep mode
[Disable] [ Enable]
If disabled, LCD and communicat ion
will t ur n OFF immediat ely af t er
UPS is OFF.
If enabl ed, LCD and communicat ion
st ays ON 1h30 min af t er UPS is OFF.
Disable
Remot e command
[Disable] [Enabl e]
If enabled, shut dow n or rest art commands
f r om sof t w ar e ar e aut horised.
Enable
RPO delay
[0 s] [1s ] [2 s]...[180 s]
Delays remote power off command
[0 s]
Battery settings
Aut omat ic bat t ery
t est
[No t est ] [ Every day] [ Every week]
[ Every mont h]
Availabl e only if bat t ery charge
mode is set t o const ant charge.
Every week(in constant charge,
otherwise following ABM
battery test method)
Low bat t ery warning
[1 %] [2 %] ... [100 %]
The alarm t riggers when t he set
per cent age of bat t er y capacit y is
reached during a back-up t ime.
20 %
Rest art bat t ery
level
[1 %] [2 %] ... [100 %]
If set , aut omat ic rest art wil l occur
only when percent age of bat t ery
charge is reached.
0%
Bat t ery charge mode
[ ABM cycling] [ Const ant charge]
ABM cycling
Ext ernal bat t ery
[ Aut o det ect ion] [ Manual EBM set .]
[Manual bat t ery set . ]
[Auto detection]
Using standard EBM, UPS
detects automatically the
number of EBM connected
Deep discharge
prot ect ion
[Yes] [ No]
If set t o Yes, t he UPS aut omat ical ly
prevent s bat t ery f rom deep
discharge by adapt ing end of
back-up t ime volt age t hreshold.
Yes

Page 12
5P 750VA-1.5 KVA US_EN
3. Installation
3.1 Unpacking and contents check
(9) 5P UPS
(10) Rail and wall mounting kits
(11) Quick start, safety instructions and environmental document
(12) RS232 communication cable
(13) USB communication cable
Packing materials must be disposed of in compliance with all local regulations concerning waste.
Recycling symbols are printed on the packing materials to facilitate sorting.
⑨
⑩
⑪
⑫
⑬

Page 13
5P 750VA-1.5 KVA US_EN
3.2 Battery module connection
Caution: Before starting the UPS, please connect the internal battery.
.
A. Remove the center panel
B. Remove the left-hand side of
the front panel
C. Connect the battery module
(never pull on the wires)
D. Attach the left-hand side of the
front panel by sliding it then by
locking the push button
E. Attach the center panel
○
A
○
B
○
C
○
E
○
D

Page 14
5P 750VA-1.5 KVA US_EN
3.3 Rack installation
Follow steps 14 to 16 for model mounting on the rails.
Use provided screws on step 15 of installation. Using a longer screw could present a safety risk.
The rails and necessary hardware are supplied by EATON.
③
⑮
⑭
⑮
⑯
⑯

Page 15
5P 750VA-1.5 KVA US_EN
3.4 Wall mounting of rack model
Use provided screws on step 17 of installation. Using a longer screw could present a safety risk.
⑰
⑰
⑱
⑱

Page 16
5P 750VA-1.5 KVA US_EN
3.5 Communication ports
Connection of RS232 or USB communication port
The RS232 and USB communication ports can operate simultaneously.
Installation of the communication cards (optional)
Characteristics of the contact RS232 communication port
When a signal is activated, the contact is closed between the common (pin 2) and the pin
for the corresponding signal.
Contact characteristics (optocoupler)
•Voltage: 48 V DC max
•Current: 25 mA max
•Power: 1.
⑥
⑦
②
It is not necessary t o shut down t he
UPS bef ore inst al ling a communicat ion
card
1.
Remove the slot cover (2) secured
by screws;
2.
Insert the communication card in the
slot
3.
Secure the card cover with the 2
screws.
1.
Connect the RS232 (12) or USB (13)
communication cable to the serial or
USB port on the computer equipment.
2.
Connect the other end of the
communication cable (13) or (12) to the
USB (7) or RJ45 (6) communication
port on the UPS.
The UPS can now communicat e wit h
EATON power management sof t ware.
•
Pins 1, 3, 4, 5, 6, 10: not used
•Pin 2: common (user)
•Pin 7: low bat t ery
•Pin 8: operat ion on bat t ery power
•Pin 9: UPS ON, equipment supplied
n. o. : nor mally open cont act
⑬
⑫

Page 17
5P 750VA-1.5 KVA US_EN
4. Operation
4.1 Start-up and Normal operation
To start the UPS:
1. Verify that the UPS power cord is plugged in.
2. The UPS front panel display illuminates and shows EATON logo.
3. Verify that the UPS status screen shows .
4. Press the button on the UPS front panel for at least 2 seconds.
The UPS front panel display changes status to "UPS starting...".
5. Check the UPS front panel display for active alarms or notices. Resolve any active alarms before
continuing. See "Troubleshooting" in section 5.1.
If the indicator is on, do not proceed until all alarms are clear. Check the UPS status from the front
panel to view the active alarms. Correct the alarms and restart if necessary.
6. Verify that the indicator illuminates solid, indicating that the UPS is operating normally and any loads
are powered and protected.
The UPS should be in Normal mode.
4.2 Starting the UPS on Battery
Before using this feature, the UPS must have been powered by utility power with output enabled at
least once.
Battery start can be disabled. See the "Cold start" setting in "ON/OFF Settings" in section 2.6.
To start the UPS on battery:
1. Press the button on the UPS front panel until the UPS front panel display illuminates and shows
a status of "UPS starting...".
The UPS cycles through Standby mode to Battery mode. The indicator illuminates solid.
The UPS supplies power to your equipment.
2. Check the UPS front panel display for active alarms or notices besides the "Battery mode" notice
and notices that indicate missing utility power. Resolve any active alarms before continuing.
See "Troubleshooting" in section 5.1.
Check the UPS status from the front panel to view the active alarms. Correct the alarms and restart
if necessary.
4.3 UPS Shutdown
To shut down the UPS:
1. Press the button on the front panel for three seconds.
The UPS starts to beep and shows a status of "UPS shutting OFF...". The UPS then transfers to Standby
mode, and the indicator turns off.
4.4 Operation on Battery Power
Transfer to battery power
• The connected devices continue to be supplied by the UPS when AC input power is no longer available.
The necessary energy is provided by the battery.
• The and indicator illuminates solid.
• The audio alarm beeps every ten seconds.
The connected devices are supplied by the battery.

Page 18
5P 750VA-1.5 KVA US_EN
Low-battery warning
• The and indicator illuminates solid.
• The audio alarm beeps every three seconds.
The remaining battery power is low. Shut down all applications on the connected equipment because
automatic UPS shutdown is imminent.
End of battery backup time
• LCD displays "End of backup time".
• All the LEDs go OFF.
• The audio alarms stops.
4.5 Return of AC Input Power
Following an outage, the UPS restarts automatically when AC input power returns (unless the restart
function has been disabled) and the load is supplied again.
4.6 UPS remote control functions
The 5P offers a choice between two remote control functions.
• RPO: Remote Power Off allows a remote contact to be used to disconnect all the equipment connected to
the UPS. Restarting the UPS requires manual intervention.
• ROO: Remote ON/OFF allows remote action of button to shut down the UPS.
These functions are obtained by opening a contact connected between the appropriate pins of connector (8)
on the rear panel of the UPS (see figures below).
Remote control connection and test
1. Check that the UPS is OFF and disconnected from the AC input source.
2. Remove connector (8) after unscrewing the screws.
3. Connect a normally closed volt-free contact (60 V DC / 30 V AC max., 20 mA max., 0.75 mm2 cable
cross-section) between the two pins of connector (8) (see diagram).
Contact open: UPS shutdown
Contact closed: UPS start-up (UPS connected to AC power and AC power is available)
Note. The local ON/OFF control using button overrides the remote-control function.
Contact open: UPS shutdown, LED goes ON.
To return to normal operation, deactivate the remote external contact and restart
the UPS by pressing button .
4. Plug connector (8) into the back of the UPS.
5. Connect and restart the UPS following the previously described procedures.
6. Activate the external remote shutdown contact to test the function.
Warning. This connector must only be connected to SELV (Safety Extra-Low Voltage) circuits.
⑧
⑧
⑧

Page 19
5P 750VA-1.5 KVA US_EN
5. Maintenance
5.1 Troubleshooting
Operation status
Possible cause
Action
Batteries disconnected
The UPS does not recognize t he int ernal bat t eries
If t he condit ion per sist s, cont act your
service represent at ive
The bat t eries are disconnect ed
Verify that all batteries are properly
connected. If the condition persists,
contact your service representative.
Overload
Power requirements exceeds the
UPS capacity (greater than 105 %
of nominal)
Remove some of the equipment from
the UPS. The UPS continues to
operate, but may shutdown if the load
increases. The alarm resets when the
condition becomes inactive.
End of battery life
The end of the battery life is reached.
Contact your service representative
for battery replacement.
Event
An UPS event occurs
Example:
Remote Power OFF, the RPO
contact has been activated to
shutdown the UPS and now
prevents restart.
Set the contact back to its normal
position and press button to
restart.
UPS fault
The UPS has an internal fault.
The UPS does not protect the
equipment anymore.
Note. the alarm message and
the UPS Serial Number, then contact
your service representative.

Page 20
5P 750VA-1.5 KVA US_EN
5.2 Battery-module replacement
Safety recommendations
The battery can cause electrocution and high short-circuit currents. The following safety precautions are required
before servicing the battery components:
• remove watches, rings, bracelets and all other metal objects from the hands and arms,
• use tools with an insulated handle.
Mounting the new battery module
Carry out the above instructions in reverse order.
• To ensure safety and high performance, use only batteries supplied by EATON.
• Take care to firmly press together the two parts of the connector during remounting.
A. Remove the center panel
B. Remove the left-hand side of the
front panel
C. Disconnect the battery module by
separating the two connectors
D. Remove the metal protection
cover in front of the battery (one
screw)
E. Remove the battery module and
replace it
○
A
○
B
○
C
○
D
○
E