Eaton Powerware 9170+ Manual

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 1 of 12
UPS model: 9170+ UPS
Date: 09/1/2016

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 2 of 12
Contents
1. General information
2. Firmware download
3. Flash procedure
4. Verifying the firmware flash
5. Troubleshooting

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 3 of 12
1. General Information
There are 3 types of Modules that can be flashed based on unit configuration.
Part numbers for the modules can be located in the upper right hand corner of
the module. See the pictures at the end of instructions for examples:
ASY-0673 Brown Label Split phase power module
ASY-0675 Orange Label optional charger Module
ASY-0674 White Label Universal Power Module
System refers to the Interface board in the UPS Chassis.
Before flashing the 9170+ the unit must be in the off mode. If your system is
hardwired you must externally bypass the unit before proceeding. When performing
this procedure, ensure you are using a straight thru 9 pin serial cable.
Before upgrading the firmware to the latest version, check to ensure your
unit is at version V2.19 or greater for both the power modules and system. If your
system is not at version 2.19 Ensure you upgrade the system and power modules
to 2.19 before proceeding to a higher revision firmware level. (See verifying
system flash section below to check you current version). Contact Eaton
technical support at 1-800-356-5737 option 2 to obtain version 2.19 firmware.
The Charger module ( ASY-0675) can be upgraded directly to latest firmware
version.
If communication is interrupted at any time during the execution of the flash program
this will cause damage to the power modules and interface board. It is
recommended to flash half the power modules at any one time. Ensure all other
power modules are pulled from the system before the flash executable is started.

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 4 of 12
2. Firmware download
1. Go to the Power Quality Website.
(http://powerquality.eaton.com/Support/Software-Drivers/ )
2. Select your product, 9170+, and select your solution type, Firmware. Click on the
Download 9170+ Firmware update link.

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 5 of 12
3. Click on the required link.
Firmware Files
Upgrade
Instructions

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 6 of 12
3. Flash Procedure
1. Before starting the upgrade please ensure that if you have an external bypass
switch that the switch is placed in the line position. If you do not have a
bypass switch ensure the loads have been powered down prior to
proceeding.
2. Turn UPS off via the front panel. When the UPS is in the off mode the display
will read as follows.

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 7 of 12
3. Connect a 9 pin serial cable to the communications port on the back of the UPS
system.
4. There should be three executable files, the interface, power module and charger
module (if applicable). Double click the appropriate .exe file you wish to flash
and the file command window should then open up.

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 8 of 12
5. Choose the com port that you are using to communicate with the UPS.

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 9 of 12
6. Press flash and the upgrade will begin.
7. Once the Upgrade is complete you will see the following screen. If upgrading to
the most recent version of firmware you will hear a beep tone that comes from
the unit when completed, this is normal.

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 10 of 12
8. At this time it is safe to remove the power modules you just flashed and install
any remaining power modules. Repeat steps 4 thru 7 for flashing those power
modules or the interface board.

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 11 of 12
4. Verifying the Firmware Flash
1. Verify that all of the power modules and interface board have been updated.
2. Press the Menu button on the front display.
3. Press the down arrow button until the display reads SYSTEM ID.
4. Press the Enter button.
5. Press the down arrow button until the display reads SOFTWARE VERSION. This
menu item will indicate the current firmware version of the interface board. The
interface board is identified by the system setting in the menu and the number 0 in
the upper right hand corner of the display.

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 12 of 12
6. To verify the power module and charger module firmware versions press the slot
button in the bottom left hand corner of the display. Then press the down arrow
button until it reads a slot with a power/ charger module in it. The slots are
identified by a number in the upper right hand corner of the display.
7. After looking at each slot it is recommended to change the display back so that
the firmware version for the interface board is shown on the display
8. When finished press the escape button until the main menu is displayed and
proceed with the startup sequence in the user manual.

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 13 of 12

Eaton 9170+ Flash Instructions
9170+ Flash Procedure
Eaton 9170+ Flash Procedure
IL153001EN Page 14 of 12
5. Troubleshooting
1. The Eaton Flash tool will not allow you to select a com port:
a) Verify that the communications ports on your computer are free and are able to be
opened.
b) Check to make sure the communication cable is connected to the UPS 9 pin
communication port.
2. An “unknown error” displays on the flash tool after starting the flash
program:
a) Verify that the UPS is in the off mode prior to launching the flash tool.
b) Verify that the display is reading the correct number of power modules in the unit.