Ecoflo PUP62 User manual

Owner’s Manual
Electric Drill Utility Pump
PUP63 Drill Pump
PUP62
Drill Pump with Kit
General Safety . . . . . . . . . . . . . . . . . . . 2
Pre Assembly. . . . . . . . . . . . . . . . . . . . . 3
Assembly. . . . . . . . . . . .. . . . . . . . . . . . . 5
Operation . . . . . . . . . . . . . . . . . . . . . . . . 6
Maintenance . . . . . . . . . . . . . . . . . . . . . . 7
Troubleshooting . . . . . . . . . . . . . . . . . . . . 8
Planning Operation . . . . . . . . . . . . . . . . . 3
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Service Parts . . . . . . . . . . . . . . . . . . . . . . . 7
TABLE OF CONTENTS

2
ALWAYS USE EXTREME CAUTION
maintaining this product!
Important Safety Instructions
Carefully read and follow all safety
instructions in this manual and on pump.
SAVE THESE INSTRUCTIONS – This manual
contains important instructions that should be
followed during installation, operation, and
maintenance of the product.
Save this manual for future reference.
Safety Labels
This is the safety alert symbol. When you
see this symbol on your pump or in this manual,
look for one of the following signal words and be
alert to the potential for personal injury!
Indicates a hazard which, if
not avoided, will result in death or serious injury.
Indicates a hazard which,
if not avoided, could result in death or serious
injury.
Indicates a hazard which, if
not avoided, could result in minor or moderate
injury.
NOTICE indicates practices not related to
personal injury.
Keep safety labels in good condition. Replace
missing or damaged safety labels.
General Safety
Risk of burns. Do not
touch an operating motor. Motors are de-
signed to operate at high temperatures. To
avoid burns when servicing pump, allow it to
cool for 20 minutes after shut-down before
handling.
Do not allow pump or any system compo-
nent to freeze. To do so will void warranty.
Pump water only with this pump.
Periodically inspect pump and system com-
ponents.
Wear safety glasses at all times when work-
ing on pumps.
Risk of explosion. Pump
body may explode if used as a booster
pump.
NOTE: Not recommended to use for drinking
water
GENERAL SAFETY
STOP Before you start

3
WARRANTY
PRE-ASSEMBLY
PLANNING OPERATION
Warranty
WHAT IS COVERED
Thi s pump i s guar anteed for 90days from d ate ofpurchase. It will pump clean water and motor oil.
WHAT IS NOT COVERED
Pumping anything other than clean water and motor oil, and if damaged due to misuse from primarilybeing
pump (running the pump dry).
Contact the Cu stomer Service Team at1-844-883-1872 or visit www.HomeDepot.com.
Pre-Assembly
PRODUCT SPECIFICATIONS
Maximum Head at 1,200 RPM 45 ft.
Maximum Head at 800 RPM 32 ft.
Rate of Flow at 1,200 RPM 90 GPH
Rate of Flow at 800 RPM 60 GPH
Priming Self-priming up to 8 ft. vertical ly
Lubrication Pressure-lubricated bearings, shaft, and seal
PLANNING OPERATION
Carefully unpack and inspecteach part. Compare parts with the Package Contents list. If any part appears
operate this product. Contact the Customer Service Team.
TOOLS REQUIRED
Drill Garden h ose
Warranty
WHAT IS COVERED
Thi s pump i s guar anteed for 90days from d ate ofpurchase. It will pump clean water and motor oil.
WHAT IS NOT COVERED
Pumping anything other than clean water and motor oil, and if damaged due to misuse from primarilybeing
pump (running the pump dry).
Contact the Cu stomer Service Team at1-844-883-1872 or visit www.HomeDepot.com.
Pre-Assembly
PRODUCT SPECIFICATIONS
Maximum Head at 1,200 RPM 45 ft.
Maximum Head at 800 RPM 32 ft.
Rate of Flow at 1,200 RPM 90 GPH
Rate of Flow at 800 RPM 60 GPH
Priming Self-priming up to 8 ft. vertical ly
Lubrication Pressure-lubricated bearings, shaft, and seal
PLANNING OPERATION
Carefully unpack and inspecteach part. Compare parts with the Package Contents list. If any part appears
operate this product. Contact the Customer Service Team.
TOOLS REQUIRED
Drill Garden h ose
TOOLS REQUIRED
Drill Garden Hose
NOTE: If using a garden hose on the
suction side of pump, then the hose must
be walled and be kept as short as
possible. If not, then there is a risk of the
hose collapsing and blocking suction.
There can be no leaks in the suction line
or the pump will not prime.
WHAT IS COVERED
This pump is warranted against defects in material and workmanship for 90 days from date
of purchase.
WHAT IS NOT COVERED
Pumping anything other than clean water and motor oil, and if damaged due to misuse from being
run without water or oil in the pump (running the pump dry).
Contact the Customer Service Team at 1-877-326-3561
PERFORMANCE USING SUPPLIED HOSES (1/4IN. HOSE ON INLET) (3FT. GARDEN HOSE
ON DISCHARGE)
Rate of Flow at 3,500 RPM
Rate of Flow at 800 RPM
48 GPH
42 GPH
PERFORMANCE USING A HEAVY DUTY GARDEN HOSE ON INLET (NOT SUPPLIED) AND
SUPPLIED 3FT GARDEN HOSE ON DISCHARGE)
PRODUCT SPECIFICATIONS
Rate of Flow at 3,500 RPM
Rate of Flow at 800 RPM
260 GPH
60 GPH
Maximum Head at 3,500 RPM
Maximum Head at 800 RPM
Priming
Lubrication
100 ft.
32 ft.
Self-Priming up to 3 ft. vertically
Factory lubricated for first time use. Lubricate with vegetable
oil before each subsequent use
Carefully unpack and inspect each part. Pull oil tube completely out of garden hose. Compare parts
with the package contents list. If any part appears missing or damaged, do not operate this product.
Contact the customer support team.

4
PLANNING OPERATION (CONTINUED)
being run without water or oil in the
appears missing or damaged, do not
run without water or oil in the
missing or damaged, do not
PACKAGE CONTENTS
Pre-Assembly (continued)
1"$,"(&$0/5&/54
1BSU %FTDSJQUJPO 3FQMBDFNFOU1BSU
/VNCFS
2VBOUJUZ
"
0JMUVCFJOYJO0%8"EBQUFS %3--"
JO"EBQUFSJO0%BOE
JO*%  
#1VNQ %3-- 
$ GUYJO %3-- 
"
#
$
065
*/


%JTDIBSHF garden hose with a brass female fitting
PART DESCRIPTION REPLACEMENT PART
NUMBER
QUANTITY
A
B
C
1
1
1
Oil tube, 35 in. x 1/4 in. O.D. W/Adapter
3 in. Adapter (3/8 in. O.D., and 1/4 in, I.D.)
Pump
3ft. x 1/2in. Discharge garden hose with
brass female tting
60DRLL005A
60DRLL001
60DRLL006

5
ASSEMBLY
1
Preparing to pump motor oil using
adapter and tube
Remove the dipstick from the engine/motor
from which you plan to remove motor oil.
Cut at a 60 degree angle one end of tube (A).
Lubricate the pump impeller by placing several
drops of mineral or vegetable oil on the
impeller at inlet port (1).
Place the adapter tube (B) into the inlet port (1)
of the pump (C) as far as it will go in.
Insert the end of the tube (A) with the
60 degree cut into the motor dipstick hole.
Attach the garden hose (D) to port (2).
Attach drill pump with tubes and hose to drill.
Connect drill motor power cord to a 3-wire
grounded plug.
Inspect the washer in the inlet hose to
make sure it is in good condition and installed
in the hose.
Lubricate the pump impeller by placing several
drops of mineral or vegetable oil on the
impeller at inlet port (1).
Connect hose (D) to the port and suction hose
to intlet port on pump (C) outlet.
Attach the drill pump with hoses to the drill.
Connect the drill motor power cord to a 3-wire
grounded plug.
NOTE: Motor oil should be removed when at
room temperature.
Ensure drill is not connected
to electrical service as you begin this process.
2
Preparing to pump clean water using
garden hose connected to pump
Ensure drill is not connected
to electrical service as you begin this process.
Keep the inlet hose as short
as possible
The combined height of the
inlet and outlet hose should be no higher than 3
ft. above the water source and/or not more than
25 ft. horizontally from the water source.
To minimize the pump rotating
as you start the drill. To minimize the pump rotating
as you start the drill.
Ensure water is drawn into the
drill pump within 15-20 seconds to avoid damag-
ing the pump. If it does not, check to ensure the
pump (C), ensure none of the hoses are crimped
and that the suction hose is fully inserted in the
water source.
NOTE: Water should be removed when it is at
room temperature.
If water has suspended solids,
a strainer should be installed on hose (D )that is
in the water. A piece of door screen tied to end
of hose that is in the water would help keep any
solids out of the hose.
Ensure motor oil is drawn into
the drill pump within 15-20 seconds to avoid
damaging the pump. If it does not, check to
in pump (C), ensure the tube is not crimped and
that the tube is fully inserted in the dipstick hole.
C
B
A
1
D
A B
C
D
1
D
C
12
2
1 C
Do not pump oil if debris /
metal shavings are present

6
OPERATION
1Preparing for operation
2Priming the pump
NOTE: Keep the suction line as short as possible
NOTE: Never operate the impeller dry.
Operating it dry for as little as 30 seconds can
ruin the pump. The impeller must be oiled to
reduce friction or wear.
NOTE: Never operate the pump dry for prolonged
periods of time, as this will damage the pump.
NOTE: Use a strainer on the end of the inlet
hose, when pumping liquids with small solids to
extend pump life.
NOTE: Oil becomes thick in cold weather. Oil
must be kept thin for the pump to work properly.
NOTE: Electric drills are not intended to be oper-
ated unattended or continuously. Doing either of
these can cause the pump and drill to fail.
NOTE: Any air leaks in the suction line will pre-
vent the pump from priming.
NOTE: Do not overtighten screws or pump
housing damage can occur!
NOTE: Hoses of shorter lengths, larger
diameters, and stiffer walls will result in
better performance
Risk of electrical shock, per-
sonal injury or death. Never touch or handle
driven pump with wet hands or when standing on
a wet surface or in water.
Be sure the drill is always
electrically grounded to an acceptable electrical
ground.
Wet the impeller located inside the pump with
before starting the pump. This improves the
priming process.
Start the drill pump. Self-priming should
occur within 30 seconds. The pump will self-
prime up to an 8 ft. vertical lift. Be sure
that the liquid enters the pump within 15 to
20 seconds. If not, refer to the assembly
instructions and also the Troubleshooting
section.
If pump fails to prime, ensure that there are no
air leaks or obstructions in suction line.
2
IN
OUT
1
Use the unit within the liquid temperature
range of 40°F to 120°F.
Inspect hoses thoroughly before each use,
making sure that all connections are tight and
that the hoses are all in good condition.
Be sure that the inlet line (1) is airtight and
submerged in fluid. The inlet (1) and discharge
(2) lines should be free of kinks and other flow
restrictions.
If front cover is removed for impeller
maintenance, be sure to clean and lubricate the
shaft seal, impeller and O-ring before
reassembly

7
MAINTENANCE
SERVICE PARTS
Normal use of the pump causes it to wear. To extend pump life:
Lubricate the impeller with vegetable oil before each use by placing
a few drops in pump inlet (port 1)
Always flush with clear water after using
Keep the suction hose/tubing as short as possible and prime the hose/tubing
(fill with liquid) when possible before starting the pump
Do not use a suction hose that can collapse due to vacuum pressure
If front cover is removed for impeller maintenance, be sure to clean and lubricate the
shaft seal, impeller and O-ring before reassembly.
NUMBER DESCRIPTION PART NUMBER QUANTITY
1 1
12
Impeller
O-ring
EFPUP6301
EFPUP6302

8
TROUBLESHOOTING
The pump will not prime Air is leaking into the inlet
hose or connection
The inlet hose is clogged
The hose collapsed due to inlet
line suction on a flat surface
The impeller, body, and end cover
are worn from pumping abrasives
Air is leaking in at the seal
or O-ring
The shaft turns but the impeller
does not turn
Drill speed is too slow
Replace the washer in the hose
fitting or replace the hose
Clean or replace the hose
Use quality, heavy duty, thick-
walled hose on suction side
of pump
Notch the end of the inlet line
where it meets the flat surface,
use suction rated hose
Replace the pump
Replace the pump
Replace the pump
Replace the pump
The impeller blades are missing
or charred from dry running
Incrementally snug the screws on
the front cover plate to seal the
O-ring. Disassemble, clean and
lubricate all components and seals.
If O-ring or Shaft seal is damaged,
replace the pump
Increase drill speed
There is a low flow rate The drill is running too slowly
There is a restriction in the inlet
or discharge hoses
The suction hose is too long, the
diameter is too small and/or the
pump is too high above the
liquid surface
The lip seal is damaged
Increase the drill speed. Minimum
dril speed for acceptable
operation is 800 RPM. Optimal
drill speed is 3500 RPM
Clean or replace the hoses.
Check hoses to eliminate any
sharp bends or kinks in the lines
Use appropriate hose and
pumping setup to maximize
performance
Liquid is leaking where
the shaft enters the
pump body
Problem Probable Cause Corrective Action

WARRANTY
Retain Original Purchase Receipt for Warranty Eligibility
Limited Warranty
Manufacturer warrants to the original consumer purchaser (“Purchaser” or “You”) that its products are free from defects
in material and workmanship for a period of 90 days from the date of the original consumer purchase. If,
within 90 days from the original consumer purchase, any such product shall prove to be defective, it shall
be repaired or replaced at manufacturer’s option, subject to the terms and conditions set forth herein. Note that this limited
warranty applies to manufacturing defects only and not to ordinary wear and tear. All mechanical devices need periodic
parts and service to perform well. This limited warranty does not cover repair when normal use has exhausted the life of a
part or the equipment.
The original purchase receipt and product warranty information label are required to determine warranty eligibility. Eligibil-
ity is based on purchase date of original product – not the date of replacement under warranty. The warranty is limited to
repair or replacement of original purchased product only, not replacement product (i.e. one warranty replacement allowed
per purchase).
Purchaser pays all removal, installation, labor, shipping, and incidental charges.
Claims made under this warranty shall be made by returning the product to the retail outlet where it was purchased or to
the factory immediately after the discovery of any alleged defect. Manufacturer will subsequently take corrective action as
promptly as reasonably possible. No requests for service will be accepted if received more than 30 days after the warranty
expires. Warranty is not transferable and does not apply to products used in commercial/rental applications.
General Terms and Conditions; Limitations of Remedies
You must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty does
not apply to the following: (1) acts of God; (2) products which, in manufacturer’s sole judgment, have been subject to
negligence, abuse, accident, misapplication, tampering, or alteration; (3) failures due to improper installation, operation,
maintenance or storage; (4) atypical or unapproved application, use or service; (5) failures caused by corrosion, rust or
other foreign materials in the system, or operation at pressures in excess of recommended maximums.
This warranty sets forth manufacturer’s sole obligation and purchaser’s exclusive remedy for defective products.
MANUFACTURER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES
WHATSOEVER. THE FOREGOING LIMITED WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS
AND IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE FOREGOING LIMITED WARRANTIES SHALL NOT EXTEND
BEYOND THE DURATION PROVIDED HEREIN.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an
implied warranty lasts, so the above limitations or exclusions may not apply to
rights and You may also have other rights which vary from state to state.
1899 Cottage Street, Ashland, Ohio 44805
Teléfono: 1-877-326-3561
Fax: [phone]
EF-0144 Drill Pump OM rev#11/2020