Ecostrad ALLORA User manual

Ecostrad Designer Electric Radiators
ALLORA
Horizontal

Ecostrad_Allora_H_V1.2_03092021 2
1 | Warnings & Precautions
Please read these instructions thoroughly before commencing installation.
Check that all ancillary components are present and that the product has not
suffered any damage during transit.
This radiator is supplied with an electric heating element and is for use with an
electric supply only. The product cannot be used as part of a central heating system
or as a dual source radiator. This radiator has been pre-filled and adjusted for
electric use. No filling is required. Do not remove any of the seals as this might
cause leakages and void the warranty. Improper adjustment of the fluid level in the
radiator can cause malfunction.
The radiator can be used for heating throughout the home provided it is fitted with
and controlled via the supplied heating element. Consult the manual of the supplied
element for full safety, installation and functionality details.
Warning
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience or
knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure they do not play with the appliance.
Warning
As with conventional radiators, this electric radiator will get hot to the touch
during operation. If the radiator is left on full power for a prolonged period
of time the surface temperature can rise to 70 °C (+/- 5 °C).
Warning
When drilling or fixing into walls, floors or ceilings it is essential you check for
pipes and wires before commencing. Please ensure that you wear all
necessary personal protective equipment.

Ecostrad_Allora_H_V1.2_03092021 3
2 | Installation
1 – Components
Before beginning installation, check that all fixings are supplied. The radiator should
only be mounted with the manufacturer’s fixings.
Part
Description
Qty
A Left
Brackets
3
B Right
Brackets
2
C Bracket
Guards
5
D Wall Plugs 5
E
Washers
5
F
Wall Screws
(ST6x65mm)
5
G Element * 1
* The heating element is packaged separately from the radiator and may arrive in
a separate delivery.
2 – Fitting the Element
Full instructions for fitting the element can be found within the element manual. The
user must ensure installation is in accordance with the following:
•The element must be fitted at the bottom of the radiator on the side. It may
be fitted on the left or right side.
•The heating element must not be connected to the electric supply until it is
secured inside the radiator and correctly orientated.
•The radiator is filled with an anti-freezing liquid exactly to the level required
by the element. Ensure that no liquid is lost during installation.
•Do not hang the radiator with the heating element at the top.

Ecostrad_Allora_H_V1.2_03092021 4
3 – Wall Mounting
1. Check that the wall is strong enough to hold the weight of the pre-filled
radiator.
a. The fixings supplied are suitable for use in solid masonry. For any
other wall type you will need to source appropriate fixings.
b. If fitting to a plasterboard wall, either fit directly to the wooden struts
or strengthen the wall; do not fix through plasterboard alone.
c. If you are fitting the radiator to a stud wall and struggling to line the
bracket positions up with the studs, swapping one or both bracket sets
so that the back plates flip to the other side may give you the
necessary flexibility. Additional brackets, if required, are available on
request.
2. Identify the points where the Brackets (A,
B) will slot between the radiator bars.
a. Place the Bracket Guards (C) in
the Brackets (A, B).
b. The Brackets (A, B) should slot
between the bars with their
mounting plates facing together:
with the Left Brackets (A) on the
left and the Right Brackets (B) on
the right as you face the radiator.

Ecostrad_Allora_H_V1.2_03092021 5
3. Choose the mounting location and affix
the Brackets (A, B) accordingly.
a. Use a tape measure, spirit level
and pencil to mark the bracket
locations, as per step 2.
b. Using a 10mm drill bit, drill four
holes in the marked locations and
push the Wall Plugs (D) inside.
c. Position the Wall Brackets (A, B)
over the holes and fix in place
using the Washers (E)and Wall
Screws (F).
4. The radiator is now ready to mount. You
may choose to add the optional security
bracket at this stage.
a. Lift the radiator onto the Brackets
(A, B).
b. OPTIONAL – Position the
remaining Bracket (A) pointing
downwards above one of the top
brackets, such that the radiator
top bar is now locked in place.
Mark the bracket location on the
wall before lifting the radiator off
the brackets.
c. Use the 10mm drill bit to drill the marked bracket hole and push the
remaining Wall Plug (D) inside. Replace the radiator, re-position the
bracket and use the remaining Washer (E) and Wall Screw (F) to fix.
4 – Connecting the Element
Wiring the heating element to the mains is a job for a qualified electrician. Please
consult the element manual for full instructions and safety warnings, paying special
consideration to the following:
•The radiator and its element are designed to be used under AC 230 voltage
and should be connected to the household fixed wiring by a qualified
electrician in accordance with national wiring regulations.

Ecostrad_Allora_H_V1.2_03092021 6
•Do not install the radiator under or in front of a power socket or connector
box.
•The power lead must be connected to a socket which must be at least 25cm
from the floor. Do not connect the element to the power supply until it is
secured within the radiator and correctly orientated, as above.
3 | Cleaning
Regular cleaning with a soft, damp cloth will keep the surface of your product
looking new. Do not use abrasive or chemical cleaners as these will damage the
finish over time.
4 | Warranty
The Ecostrad Allora carries a 10-year guarantee on the steel body, a 3-year
guarantee on paintwork and a 2-year guarantee on electrical components. Within
the stated period, starting from the date the customer receives their unit, Ecostrad
guarantee to repair or replace the unit where a fault is due to defects in materials
or manufacturing.
The warranty does not cover any defect arising from damage, negligence, usage
outside the product’s intended purpose or fair wear and tear. The warranty is only
valid when the radiator has been used with the supplied heating element, at the
specified supply voltage, and in accordance with all conditions specified in this
manual. The warranty will be void if the radiator has been tampered with, if its fluid
levels have been adjusted, or if the ratings label has been removed.
The warranty does not cover failures and faults due to force majeure, accidental
damage, mishandling, external impact, chemical agents or atmospheric
phenomena, incorrect use of the unit, the purchaser’s faulty electrical installations,
transporting the unit or problems caused by the unit being handled by persons not
authorised by Ecostrad. An invoice may be required to confirm that installation
work has been carried out by a qualified professional. Ecostrad cannot accept
responsibility for damage, loss or injury caused by incorrect installation,
maintenance, cleaning or covering the unit.
The warranty is a contract with the original purchaser and does not transfer if the
unit is re-sold, gifted or inherited. Proof of purchase, including order number and
order confirmation or invoice, will be required if a claim is made. The warranty
covers only the model of heater shown on the purchase invoice. The warranty
covers the repair or replacement of the defective product only and Ecostrad shall
have no liability for installation costs or consequential losses however incurred.

Ecostrad_Allora_H_V1.2_03092021 7
Claims must be made with the establishment where the unit was purchased. This
warranty does not affect the customer’s consumer rights.
5 | Disposal
The icon with the crossed-out waste bin on electrical or electronic
equipment stipulates that this equipment must not be disposed of with
household waste at the end of its life. You will find collection points for
free return of waste electrical and electronic equipment in your
vicinity. The addresses can be obtained from your local authority.
The separate collection of waste electrical and electronic equipment enables the
re-use, recycling and other forms of recovery of waste equipment, and prevents
any negative effects for the environment or human health caused by the disposal of
hazardous substances potentially contained in the equipment.