Edelbrock 25-9213 User manual

©2004 Edelbrock Corporation
Catalog #47490 &#47492 Page 1of 2 Rev. 7/04
Edelbrock Header
For 2000-2004 PT Cruiser
Catalog #47490 & #47492
INSTALLATION INSTRUCTIONS
Please study these instructions carefully before installing your new Header. If you have any questions or problems, please
contact our Technical Hotline at : 1-800-416-8628 from 7 am - 5pm, Monday-Friday, Pacific Standard Time or e-mail
us at [email protected]. Please fill out and mail your warranty card.
Suggested Tools Needed for Installation:
❑ Metric wrench set, metric sockets, and ratchet
❑ Screwdrivers
❑Floorjack and Jackstands
SPECIAL NOTICE: This Edelbrock part has received an Executive Order number (E.O.#) from the California Air Resources
Board (C.A.R.B.) making it legal for street use in all 50 states. To assist you with emission equipment certification, we
have included a silver fan shroud decal to help testing personnel verify the this part is a legal replacement on the vehicle
for which it is cataloged. The adhesive-backed decal should be affixed next to the existing emission and engine
specifications decal. Do not cover any part of your original emission decal.
WARNING: The use of "Thermal Wrap" will void the warranty on your Edelbrock Headers. Those product will cause
excessive heat and moisture buildup resulting in corrosion and failure of the header.
KIT CONTENTS
Qty. Part # Description
125-9213 Header
154-4749 Port Gasket
154-4750 Collector Gaskets
360-4749 8mm x 1.25 Lock Nut
460-7275 5/16-18 Hex Nuts
10 68-0350 8mm x 30mm Hex Bolts
168-4749 10 x 1.50 x 12mm Hex Bolt
468-6010 5/16-18 x 1 1/2” Hex Bolt
178-2004 TieWrap
179-9722 Heat Shield
782-8721 5/16 Hardened Washers
14 82-4620 Lock Washers
182-8722 Flat Washer

©2004 Edelbrock Corporation
Catalog #47490 &#47492 Page 2of 2 Rev. 7/04
Edelbrock Corporation
2700 California St.
Torrance, CA 90503
Tech Line: 1-800-416-8628
Office: 310-781-2222
Tech Fax: [phone]
E-Mail: [email protected]
Assembly
1. Place the supplied port gasket over the studs (if
equipped) on the cylinder head. Install the Edelbrock
Header on the studs (if equipped) using the provided
8mm bolts, and lock washers on all bolts. Use
supplied lock nuts and hardened washers on the
studs (if equipped). Tighten all flange bolts and nuts
at this time.
2. Re-install the catalytic converter to the hangers.
Using the supplied 5/16 bolts, nuts, lock washers,
and hardened flat washers and gaskets, attach the
catalytic converter to the header collector flange.
Note: (The lower bolt of the collector is used to
secure the supplied heat shield). Using supplied
10mm bolt and washer, attach the heatshield to the
block just above the oil pan rail.
3. Check all hydraulic, vacuum, water, and fuel lines to
ensure there is adequate clearance from the header.
Using anti-seize on threads, install O2 sensor and re-
connect plug.
4. Re-connect the battery.
5. At this point, it is a good idea to check everything
over to make sure nothing was missed during
assembly.
6. Start vehicle and bring vehicle up to operating
temperature. Check for leaks of any kind.
7. Turn off engine and let cool. Tighten all the bolts
again.
Disassembly
1. Raise and support the vehicle on a flat stable surface
using the floorjack and proper load rated jackstands.
2. Disconnect the battery.
3. Removenut andbolts retainingheatshield andremove
heatshields.
4. Remove four nuts that retain catalytic converter to the
stock manifold.
5. Unplug and unclip oxygen sensor wire located above
the catalytic converter.
6. Remove the clamp retaining the catalytic converter
pipe to the intermediate pipe and unhook the catalytic
pipe brackets from the hangers. Remove catalytic
converter.
7. Unbolt and remove the stock manifold and gasket.
INSTALLATION INSTRUCTIONS