Edelbrock 47493 User manual

©2006 Edelbrock Corporation
Catalog #47492, #47493 Page 1 of 2 Brochure #63-47492
Rev. 5/06 - DA/mc
Edelbrock Header
For 2000-2004 PT Cruiser
Catalog #47492 & #47493
INSTALLATION INSTRUCTIONS
Please study these instructions carefully before installing your new Header. If you have any questions, please contact our
Technical Hotline at : 1-800-416-8628 from 7 am - 5pm, Monday-Friday, Pacific Standard Time or e-mail us at
[email protected]. Please fill out and mail your warranty card.
Suggested Tools Needed for Installation:
❑ Metric wrench set, metric sockets, and ratchet
❑ Screwdrivers
❑Floorjack and Jackstands
SPECIAL NOTICE: This Edelbrock part has received an Executive Order number (E.O.#) from the California Air Resources
Board (C.A.R.B.) making it legal for street use in all 50 states. To assist you with emission equipment certification, we
have included a silver fan shroud decal to help testing personnel verify the this part is a legal replacement on the vehicle
for which it is cataloged. The adhesive-backed decal should be affixed next to the existing emission and engine
specifications decal. Do not cover any part of your original emission decal.
WARNING: The use of "Thermal Wrap" will void the warranty on your Edelbrock Headers. Those product will cause
excessive heat and moisture buildup resulting in corrosion and failure of the header.
Qty.Part # Description
❑1 25-9213 Header (#47492)
❑1 25-9300 Header (#47493)
❑1 54-4749 Port Gasket
❑1 54-4750 Collector Gaskets
❑3 60-4749 8mm x 1.25 Lock Nut
❑4 60-7275 5/16-18 Hex Nuts
❑10 68-0350 8mm x 30mm Hex Bolts
KIT CONTENTS
Catalog #47492 (Ceramic-Coated)
Catalog #47493 (Ti-Tech Coated)
Qty.Part # Description
❑1 68-4749 10 x 1.50 x 12mm Hex Bolt
❑4 68-6010 5/16-18 x 1 1/2” Hex Bolt
❑1 78-2004 Tie Wrap
❑1 79-9722 Heat Shield
❑7 82-8721 5/16 Hardened Washers
❑14 82-4620 Lock Washers
❑1 82-8722 Flat Washer
IMPORTANT NOTE:
Proper installation is the responsibility of the installer. Improper installation will void warranty and may
result in poor performance and engine or vehicle damage.

©2006 Edelbrock Corporation
Catalog #47492, #47493 Page 2 of 2 Brochure #63-47492
Rev. 5/06 - DA/mc
Edelbrock Corporation, 2700 California St., Torrance, CA 90503
Tech Line: 1-800-416-8628
E-Mail: [email protected]
ASSEMBLY
1. Place the supplied port gasket over the studs (if
equipped) on the cylinder head. Install the Edelbrock
Header on the studs (if equipped) using the provided
8mm bolts, and lock washers on all bolts. Use
supplied lock nuts and hardened washers on the
studs (if equipped). Tighten all flange bolts and nuts
at this time.
2. Re-install the catalytic converter to the hangers.
Using the supplied 5/16 bolts, nuts, lock washers,
and hardened flat washers and gaskets, attach the
catalytic converter to the header collector flange.
Note: (The lower bolt of the collector is used to
secure the supplied heat shield). Using supplied
10mm bolt and washer, attach the heatshield to the
block just above the oil pan rail.
3. Check all hydraulic, vacuum, water, and fuel lines to
ensure there is adequate clearance from the header.
Using anti-seize on threads, install O2 sensor and re-
connect plug.
4. Re-connect the battery.
5. At this point, it is a good idea to check everything
over to make sure nothing was missed during
assembly.
6. Start vehicle and bring vehicle up to operating
temperature. Check for leaks of any kind.
7. Turn off engine and let cool. Tighten all the bolts
again.
DISASSEMBLY
1. Raise and support the vehicle on a flat stable surface
using the floorjack and proper load rated jackstands.
2. Disconnect the battery.
3. Remove nut and bolts retaining heatshield and remove
heatshields.
4. Remove four nuts that retain catalytic converter to the
stock manifold.
5. Unplug and unclip oxygen sensor wire located above
the catalytic converter.
6. Remove the clamp retaining the catalytic converter
pipe to the intermediate pipe and unhook the catalytic
pipe brackets from the hangers. Remove catalytic
converter.
7. Unbolt and remove the stock manifold and gasket.
INSTALLATION INSTRUCTIONS