Edelbrock Cat-Back Exhaust System 5714 User manual

©2006 Edelbrock Corporation
Catalog #5714
Page 1 of 2 Brochure #63-5714
Rev. 7/06 - KS/DA/mc
EDELBROCK CAT-BACK EXHAUST SYSTEM
For 2006 Dodge Ram, 1500 Quad Cab,
5.7L Hemi V8, 2 & 4 WD
Catalog #5714
INSTALLATION INSTRUCTION
Please study these instructions carefully before installing your new Cat-Back Exhaust System. If you have any questions,
contact our Technical Hotline at: 1-800-416-8628 from 7 am - 5 pm, Monday through Friday, Pacific Standard Time
or e-mail us at [email protected].
SUGGESTED TOOLS FOR INSTALLATION:
❑3/8" ratchet with deep SAE and metric sockets
❑9/16” and 15mm wrenches
❑Jackstands and jack
❑Liquid penetrant and rubber lubricant
DISASSEMBLY
1. Raise vehicle and support with proper
jackstands for the weight, leaving the
suspension hanging.
2. Use caution around hot exhaust systems to
avoid burns.
3. Use penetrating oil on all nuts and bolts.
4. Remove the bolts and clamps from the system
and lubricate the rubber hangers to ease
removal.
5. Use a long pry bar to pull the rubber hangers off
of the pipe hangers.
6. Remove the old system. In some cases, you will
find it easier to cut the overaxle pipe to remove
it.
ASSEMBLY
1. Clamp the intermediate pipe (#25-3250) to the
catalytic converter with a 3” band clamp and
just snug the clamp at this time. Slide hanger
clamp assembly (#23-4083) onto intermediate
pipe and engage wire into original front rubber
isolator. Leave clamp loose at this time.
WARNING: Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any leaks before
driving!
IMPORTANT NOTE:
Proper installation is the responsibility of the installer. Improper installation will void warranty and may
result in poor performance and engine or vehicle damage.
2. Install hanger clamp assembly #23-4084 into the
second I-pipe isolator on frame.
3. Slip the muffler onto the intermediate pipe with a
3” band clamp on the front. Inlet of muffler is
stamped in the nipple.
4. Install hanger clamp assembly (#23-4085) onto
outlet end of muffler, engage hangers into the
stock rubber isolators and slip it onto the muffler
outlet. Slip the overaxle pipe over the rear end
and into the muffler outlet.
5. Install hanger clamp assembly (#23-4086) onto
rear of the overaxle pipe and engage into factory
isolator.
6. Install tailpipe and snug clamp.
7. Working from the front of the system, align and
tighten each pipe from the cat-back.
8. Check for clearance to body, frame, and driveline
as you tighten and align the system from front to
rear.
9. Check for leaks and correct, if any are found.
INSTALLATION INSTRUCTIONS

©2006 Edelbrock Corporation
Catalog #5714
Page 2 of 2 Brochure #63-5714
Rev. 7/06 - KS/DA/mc
KIT CONTENTS
CATALOG #5714
WARNING: Support your vehicle with proper
jackstands or ramps rated for the total
vehicle weight. Place stands so that the rear
axle is allowed to hang free for easy system
removal.
WARNING: These cat-back systems are
engineered to fit vehicles with stock catalytic
converters or equivalent replacements. If
your original system has been modified,
Edelbrock will not warranty fit or
performance.
Overaxle Pipe Assembly
Intermediate Pipe Assembly
Hanger Clamp Assembly
SDT Series Muffler #55725
Qty Part # Description
❑125-3250 Intermediate Pipe
❑1 25-55725 Muffler
❑123-3251 Overaxle Pipe Assembly
❑125-3157 Tail Pipe
Band Clamp
Tail Pipe Assembly
Edelbrock Corporation, 2700 California Street, Torrance, CA 90503
Tech Line: 1-800-416-8628
E-mail: [email protected]
Qty Part # Description
❑246-6612 3” Band Clamps
❑123-4083 I-Pipe Hanger Clamp Assembly*
❑123-4084 I-pipe Hanger Clamp Assembly*
❑123-4085 Muffler Hanger Clamp Assembly
❑123-4086 Tail Pipe Hanger Clamp Assembly*
*Not Shown.