Edge-Core EAP104 User manual

– 1 –
Quick Start Guide
E032023-CS-R02
www.edge-core.com
Indoor Wall-Plate Wi-Fi 6 Access Point
EAP104 (T) | EAP104 (TL)
Package Contents
Mount the AP
a. Mounting on a Wall Junction Box
1. At the wall junction box, use two screws to secure the mounting
bracket to the box. The bracket must be installed with the marking
“UP” at the top.
2. Connect the Ethernet cable from the junction box to the Uplink (PoE)
RJ-45 port on the rear of the device. When connected to a PoE
source, the Uplink (PoE) port connection provides power to the unit.
3. With its ports facing down, place the AP over the bracket and then
slide it down until it is in its secured position.
4. Use the included security screw to secure the bracket to the AP.
5. (Optional) Connect a local LAN switch or computers to the LAN1 to
LAN4 1000BASE-T RJ-45 ports.
Warning: For indoor use only. The access point, AC power
adapter, and all connected cables are not for outdoor use.
Note: When not connected to a PoE source, you can power
the AP using the optional AC power adapter.
1
US/Japan/
Taiwan Box EU Box
12
3
4
5
Overview
Installation
1. Pass-Thru Port: Bottom panel to rear panel connection.
2. LAN4 Port: 1Gbps LAN connection and PoE out port.
3. LAN1-LAN3 Ports: 1Gbps connection to LAN devices.
4. Uplink (PoE) Port: 1Gbps connection to 802.3at PoE.
5. 12 VDC power input
6. Console port
7. Restart/Reset button:
A quick press restarts the system.
Press and hold for 5 seconds resets to factory defaults.
8. System LED Indicators:
Uplink: Green (link), Blinking (traffic)
2.4G-WiFi: On (radio on), Blinking (traffic)
5G-WiFi: On (radio on), Blinking (traffic)
Cloud: TBD
9. Power/Status LED: On (power OK), Blinking (boot up)
23
14
1
5
8
9
6
7
1. EAP104 (T)/EAP104 (TL) access point
(EAP104 (TL) does not include BLE, Zigbee, and PoE Out)
2. Mounting bracket accessory
3. Mounting bracket T8 security screw
4. RJ-45 short cable
5. Screw kit—4 screws and 4 plugs
1 2 3 4 5

Quick Start Guide
– 2 –
b. Mounting on a Wall Without a Junction Box
1. At the installation location on the wall, use the mounting bracket to
mark four holes for the wall plugs and screws. The bracket must be
installed with the marking “UP” at the top.
Drill four holes for the wall plugs, and then insert the plugs and tap
them flush with the wall surface.
Use the four screws to secure the bracket to the wall.
2. To power the AP from a PoE source, use the included short Ethernet
cable to connect the Uplink (PoE) port to the Pass-Thru port on the
rear of the device. When the Pass-Thru port on the bottom of the
device is connected to a PoE source, it provides power to the unit.
3. With its ports facing down, place the AP over the bracket and then
slide it down until it is in its secured position.
4. Use the included security screw to secure the bracket to the AP.
5. (Optional) Connect a local LAN switch or computers to the LAN1 to
LAN4 1000BASE-T RJ-45 ports.
c. Mounting Using the Optional Desktop Stand
1. At the installation location, slide the AP onto the desktop mounting
bracket and then place on the desktop.
2. Connect Ethernet cable from a PoE source to the Uplink (PoE) RJ-45
port on the rear of the AP.
Alternatively, connect Ethernet cable from a PoE source to the Pass-
Thru port on the bottom of the device and then use the included
short Ethernet cable to connect the Uplink (PoE) port to the Pass-Thru
port on the rear of the device.
3. (Optional) Connect a local LAN switch or computers to the LAN1 to
LAN4 1000BASE-T RJ-45 ports.
Check AP LEDs
1. Uplink LED — on green for a valid RJ-45 Uplink port connection.
2. 2.4G and 5G LEDs — on green for radio enabled.
3. Cloud LED — TBD
4. Power/Status LED — on green for normal operation.
Initial Setup and AP Registration
There are two options for setting up the AP for your network:
When the AP is first connected to the Internet through the
Uplink port, it is automatically redirected to ecOpen
(https://cloud.openwifi.ignitenet.com/). Enter the AP’s MAC
address and serial number for device registration.
By default, the AP is assigned an IP address through DHCP. If
the AP cannot connect to ecOpen, access the AP’s web
interface through one of the AP’s LAN ports to make
configuration changes (for example, to change from DHCP to
a static IP). See section “Connecting to the Web Interface”.
Note: Drill 2.5 mm (±0.2 mm) holes for M3 self-tapping
screws, or 4.5 mm (±0.2 mm) holes for nylon wall plugs.
Note: When not connected to a PoE source, you can power
the AP using the optional AC power adapter.
1
2
4
1
Note: When not connected to a PoE source, you can power
the AP using the optional AC power adapter.
2
4
3
2
1
3

Quick Start Guide
– 3 –
Connecting to the Web Interface
Note that you can only connect to the AP’s web interface when the AP is
not connected to the Internet.
Follow these steps to connect to the AP’s web interface through a network
connection to one of the AP’s LAN ports.
1. Connect a PC directly to one of the AP’s LAN ports.
2. Set the PC IP address to be on the same subnet as the AP LAN port
default IP address. (The PC address must start 192.168.1.x with
subnet mask 255.255.255.0.)
3. Enter the AP’s default IP address of 192.168.1.1 into the web
browser address bar.
4. Log in to the web interface using the default user name “root” and
password “openwifi”.
Safety and Regulatory Information
FCC Class B
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for
help
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
For product available in the USA/Canada market, only channel
1~11 can be operated. Selection of other channels is not possible.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm between the radiator and your
body.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that
may cause undesired operation of the device.
Cet appareil contient des émetteurs / récepteurs exempts de licence qui
sont conformes au (x) RSS (s) exemptés de licence d’Innovation, Sciences
et Développement économique Canada. L’opération est soumise aux
deux conditions suivantes:
(1) Cet appareil ne doit pas provoquer d’interférences.
(2) Cet appareil doit accepter toute interférence, y compris les
interférences susceptibles de provoquer un fonctionnement indésirable de
l’appareil.
The device for operation in the band 5150–5250 MHz is only for indoor
use to reduce the potential for harmful interference to co-channel mobile
satellite systems.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés
uniquement pour une utilisation à l’intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux.
Note: The TIP OpenWiFi SDK default URL of the DigiCert
certificate is set to ecOpen: (https://cloud.openwifi.ignitenet
.com). If you want to register the AP to your own TIP OpenWiFi
SDK, contact [email protected] to change the default
URL.

Quick Start Guide
– 4 –
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 28 cm between the
radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements
IC établies pour un environnement non contrôlé. Cet équipement doit
être installé et utilisé avec un minimum de 28 cm de distance entre la
source de rayonnement et votre corps.
CE Statement
This equipment complies with EU radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and
operated with minimum distance 24 cm between the radiator and your
body.
The device is restricted to indoor use only when operating in the
5150 to 5350 MHz frequency range.
All operational modes:
2.4 GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40),
802.11ac (VHT20), 802.11ac (VHT40), 802.11ax (HE20),
802.11ax (HE40)
5 GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac
(VHT20), 802.11ac (VHT40), 802.11ac (VHT80), 802.11ax (HE20),
802.11ax (HE40), 802.11ax (HE80)
BLE 2.4 GHz: 802.15.1
ZigBee 2.4 GHz: 802.15.4
The frequency and maximum transmitted power limit in EU are listed
as below:
2412-2472 MHz: 20 dBm
5150-5350 MHz: 23 dBm
5500-5700 MHz: 30 dBm
The abbreviations of the countries, as prescribed in above table, where
any restrictions on putting into service or any requirements for
authorization of use exist.
CE Mark Declaration of Conformance for EMI and Safety (EEC)
This information technology equipment is in compliance with the
Directive 2014/53/EU and Directive 2014/35/EU.
The Declaration of Conformity (DoC) can be obtained from
www.edge-core.com -> support -> download.
Japan VCCI Statement
5 GHz band (W52, W53): Indoor use only
NCC Statement (Taiwan)
NCC 警語
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均
不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射
頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象
時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，
指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法
通信或工業、科學及醫療用電波輻射性電機設備之干擾。
應避免影響附近雷達系統之操作。
Warnings and Cautionary Messages
AT BE BG CH CY CZ
DE DK EE EL ES FI
FR HR HU IE IS IT
LI LT LU LV MT NL
NO PL PT RO SE SI
SK TR UK
Warning: This product does not contain any serviceable user
parts.
Warning: Installation and removal of the unit must be carried
out by qualified personnel only.
Caution: Wear an anti-static wrist strap or take other suitable
measures to prevent electrostatic discharge when handling this
equipment.
Caution: Do not plug a phone jack connector in the RJ-45
port. This may damage this device.
Caution: Use only twisted-pair cables with RJ-45 connectors
that conform to FCC standards.

Quick Start Guide
– 5 –
Hardware Specifications
AP Chassis
Size (LxWxH) 160.5 x 89.5 x 34 mm (6.32 x 3.52 x 1.34 in.)
Weight 450 g (0.99 lb)
Temperature Operating: 0° C to 45° C (32° F to 113° F)
Storage: -20° C to 60° C (-4° F to 140° F)
Humidity Operating: 5% to 95% (non-condensing)
Network Interfaces
Ports Uplink(PoE) RJ-45: 1000BASE-T, PoE PD
LAN1-LAN3 RJ-45: 1000BASE-T
LAN4 RJ-45: 1000BASE-T, PoE out (PSE) (EAP104
(T) only)
Pass-Thru RJ-45: Rear to bottom
2.4 GHz Radio IEEE 802.11b/g/n/ax
5 GHz Radio IEEE 802.11a/ac/n/ax
Bluetooth Radio IEEE 802.15.1 (EAP104 (T) only)
ZigBee Radio IEEE 802.15.4 (EAP104 (T) only)
Radio Frequencies 2.4–2.4835 GHz (US, Canada, ETSI, Japan, TW)
5.15–5.25 GHz (lower band) US/Canada, TW
5.725–5.85 GHz (upper band) US/Canada, TW
Europe
5.15–5.25 GHz, 5.25–5.35, 5.47–5.725 GHz
Japan
5.15–5.25 GHz, 5.25–5.35, 5.47–5.73 GHz
Power Specifications
PoE Input Power 22.4 W max, 48 VDC–55 VDC;
802.3at-compliant
AC Power Adapter AC Input: 100–240 VAC, 50-60 Hz
DC Output: 12 VDC, 2 A
Regulatory Compliances
Radio EN300 328 V2.2.2 (2019-07)
EN301 893 V2.1.1(2017-05)
47 CFR FCC Part 15.247
47 CFR FCC Part 15.407
IC RSS-247 Issue 2 and RSS-Gen Issue 5
NCC LP0002 Section 4.10.1 (2020-07-01)
NCC LP0002 Section 5.7 (2020-07-01)
MIC certification Rule, Article 2 Paragraph 1 Item
19
MIC certification Rule, Article 2 Paragraph 1 Item
19-3
Emissions EN 301 489-1 V2.1.1 (2017-02)
EN 301 489-17 V3.1.1 (2017-02)
EN 55032:2015
AS/NZS CISPR 32:2015, Class B
47 CFR FCC Rules and Regulations Part 15
Subpart B, Class B Digital Device
ICES-003, Issue 7 Class B
CNS 13438 terminal equipment design
certification, Article 3, Article 4, Article 6, Article 9
and Article 34 regulation
Safety Low Voltage Directive IEC 62368-1:2014;and/or
EN 62368-1:2014+A11:2017; and/or BS
62368-1:2014+A11:2017
CNS 14336-1
IEC/EN 62368-1, IEC/EN 60950-1
Taiwan RoHS CNS 15663