Edge-Core ECW7220-L User manual

– 1 –
Quick Start Guide
1. Unpack the AP and Check Contents
ECW7220-L
802.11a/ac/b/g/n
Wireless Access Point
Ceiling-mount accessory
Four adhesive foot pads
Console cable—RJ-45 to DB-9
Documentation—Quick Start Guide (this document)
and Safety and Regulatory Information
Note: For Safety and Regulatory information, refer to
the Safety and Regulatory Information document
included with the AP.
Caution: The planning and installation of the AP
requires professional personnel that are trained in the
installation of radio transmitting equipment. The user
is responsible for compliance with local regulations
concerning items such as antenna power, use of
lightning arrestors, grounding, and radio mast or tower
construction. Therefore, it is recommended to consult
a professional contractor knowledgeable in local radio
regulations prior to equipment installation.
2. Mount the AP
a. Mounting on a Wall
Set two screws in the wall 116 mm (4.57 in.) apart.
Slide the AP’s wall mounting slots down onto the screws so
that the unit is secure.
1
2
1
2
b. Mounting on a Ceiling T-Bar
Position the ceiling-mount accessory clip holders on either
side of the T-bar.
Turn the ceiling-mount accessory until the two clips lock it to
the T-bar.
Slide the base of the AP onto the T-bar accessory until it is
locked in place.
Note: The ceiling mounting plate supports two different
sizes of ceiling T-bars. The position illustrated above is for
15 mm bars. Use the other position at a 90 degrees angle for
24.5 mm bars.
3. Connect Cables
Connect Category 5e or better cable to the Eth0/PoE
1000BASE-T RJ-45 port.
(Optional) Connect a local LAN switch or computer to the
Eth1 1000BASE-T RJ-45 port.
Note: The Eth0/PoE port connection also provides PoE
power to the unit.
4. Verify AP Operation
Power — on green for normal operation.
Eth0 / PoE — on green for a valid link.
Eth1 — on green for a valid link.
2.4G / 5G — on blue for 2.4 GHz or 5 GHz radio enabled.
2
3
1
1
2
3
1
2
1
2
1
2
3
4
1
2
3
4
E042015-CS-R01
150200001132A www.edge-core.com
802.11ac Controller-Based Indoor Dual Band Enterprise Access Point
ECW7220-L
All manuals and user guides at all-guides.com
all-guides.com

Quick Start Guide
– 2 –
5. Manage the AP from the Controller
The AP is designed to be managed from an EWS4502 or
EWS4606 wireless controller. For information on AP
management, refer to the wireless controller Administrator’s
Guide and CLI Command Reference, which are on the Edge-
Core web site, www.edge-core.com.
1
Hardware Specifications
Chassis
Size (WxDxH) 200 x 200 x 36.5 mm (7.87 x 7.87 x 1.44 in)
Weight 750 g (1.65 lb)
Temperature Operating: 0° C to 40° C (32° F to 104° F)
Storage: -40° C to 70° C (-40° F to 158° F)
Humidity Operating: 5% to 95% (non-condensing)
Network Interfaces
Ports Eth0/PoE Port: 1000BASE-T, PoE+ PD
Eth1 Port: 1000BASE-T
2.4 GHz Radio IEEE 802.11b/g/n
5 GHz Radio IEEE 802.11a/ac/n
Radio Frequencies 2412 - 2472 MHz (ETSI),
2412 - 2462 MHz (FCC)
5745 - 5825 MHz (China)
5180 - 5240 MHz (ETSI)
5180 - 5240 MHz, 5745 - 5825 MHz (FCC)
Power Supply
PoE Input Power 48 VDC, 0.6 A
Power Consumption 22.5 W maximum
Regulatory Compliances
Radio EN 300 328 V1.8.1:2012 (2012-06)
EN 301 893 V1.7.1:2012 (2012-06)
FCC Part 15C 15.247/15.207 (2.4-2.4835 GHz)
FCC Part 15E 15.407 (5.150GHz-5.250 GHz,
5.725-5.850 GHz)
Emissions EN 55022 2010/ AC: 2011, Class B
FCC Part 15 Subpart B, Class B
ICES-003, Issue 5, Class B
Immunity EN 55024 : 2010
EN 301 489-1 V1.9.2 (2011-09), Class B
EN 301 489-17 V2.2.1 (2012-09)
AS/NZS CISPR 22: 2009/Amdt 1: 2010, Class B
Safety UL (CSA 22.2 No. 60950-1 & UL60950-1)
CB (IEC/EN60950-1)
All manuals and user guides at all-guides.com