Edge-Core ECW5320 Programming manual

Management Guide
www.edge-core.com
IEEE 802.11a/ac/n/b/g
Enterprise Access Points
ECW5320
ECWO5320
Software Release v2.0.0.1

Management Guide
ECW5320 Indoor Enterprise Access Point
IEEE 802.11a/ac/n/b/g Dual Band Access Point
with one 1000BASE-T (RJ-45 PoE-Input) Port,
and two 100BASE-TX (RJ-45) Ports
ECWO5320 Outdoor Enterprise Access Point
IEEE 802.11a/ac/n/b/g Dual Band Access Point
with one 1000BASE-T (RJ-45 PoE-Input) Port,
and two 100BASE-TX (RJ-45) Ports
150200000964A
E012016/ST-R01

– 3 –
How to Use This Guide
This guide includes detailed information on the access point (AP) software,
including how to operate and use the management functions of the AP. To deploy
this AP effectively and ensure trouble-free operation, you should first read the
relevant sections in this guide so that you are familiar with all of its software
features.
Who Should Read
This Guide?
This guide is for network administrators who are responsible for operating and
maintaining network equipment. The guide assumes a basic working knowledge of
LANs (Local Area Networks), the Internet Protocol (IP), and Simple Network
Management Protocol (SNMP).
How This Guide
is Organized
The organization of this guide is based on the AP’s main management interfaces.
The web management interface is described in separate sections that follow the
web menu. An introduction and initial configuration information is also provided.
The guide includes these sections:
◆ Section I “Getting Started” — Includes an introduction to AP management and
initial configuration settings.
◆ Section II “Web Configuration” — Includes all management options available
through the web interface.
◆ Section III “Appendices” — Includes information on troubleshooting AP
management access.
Related
Documentation
This guide focuses on AP software configuration, it does not cover hardware
installation of the AP. For specific information on how to install the AP, see the
following guide:
Quick Start Guide
For all safety information and regulatory statements, see the following documents:
Quick Start Guide
Safety and Regulatory Information

How to Use This Guide
– 4 –
Conventions The following conventions are used throughout this guide to show information:
Note: Emphasizes important information or calls your attention to related features
or instructions.
Caution: Alerts you to a potential hazard that could cause loss of data, or damage
the system or equipment.
Warning: Alerts you to a potential hazard that could cause personal injury.
Revision History This section summarizes the changes in each revision of this guide.
January 2016 Revision
This is the first revision of this guide. It is valid for software release v2.0.0.1-r5159.

– 5 –
Contents
How to Use This Guide 3
Contents 5
Figures 9
Tables 11
Section I Getting Started 13
1 Introduction 15
Configuration Options 15
Network Connections 16
Connecting to the Web Interface 16
Setup Wizard 17
Main Menu 27
Status 28
Common Web Page Buttons 29
Section II Web Configuration 31
2 Status Information 33
System Information 33
Memory Status 34
WAN Information 34
LAN Information 35
Wireless Overview 36
Active Clients 37
Statistics 38
3 Network Settings 39

Contents
– 6 –
Operation Mode 39
LAN Setting 40
DHCP Setting 41
4 Internet Settings 43
Cable/Dynamic IP (DHCP) 43
Static (Fixed IP) 44
PPPoE (ADSL) 45
PPTP 46
L2TP 47
5 Wireless Settings 49
Basic Settings 49
Advanced Settings 52
6 Static Routes 57
7 Firewall 59
Port Forwarding 59
DMZ Configuration 60
Access Control 61
Advanced Security 62
8 System Settings 63
Language Selection 64
System Log 64
NTP 65
Password 65
Maintenance 66
Rebooting the Access Point 66
Resetting the Access Point 66
Backing Up Configuration Settings 67
Restoring Configuration Settings 67
Upgrading Firmware 67

Contents
– 7 –
Section III Appendices 69
A Troubleshooting 71
Problems Accessing the Management Interface 71
Using System Logs 71
Index 73

Contents
– 8 –

– 9 –
Figures
Figure 1: Login Page 17
Figure 2: Select Your Country 17
Figure 3: Option Mode 18
Figure 4: Route to Internet 18
Figure 5: Bridge to Internet 19
Figure 6: Client Route 19
Figure 7: Cable / Dynamic IP (DHCP) 20
Figure 8: Static (Fixed IP) 20
Figure 9: PPPoE (ADSL) 21
Figure 10: PPTP 22
Figure 11: L2TP 22
Figure 12: Setting WIFI 2.4G 23
Figure 13: Setting WIFI 5G 26
Figure 14: Scanning WIFI 5G Networks 26
Figure 15: Status Overview 28
Figure 16: Status Clients 28
Figure 17: Status Statistics 29
Figure 18: Set Configuration Changes 29
Figure 19: System Information 33
Figure 20: Memory Status 34
Figure 21: WAN Information 34
Figure 22: LAN Information 35
Figure 23: Wireless Overview 36
Figure 24: Active Clients 37
Figure 25: Statistics 38
Figure 26: LAN Setting 40
Figure 27: DHCP Setting 41
Figure 28: DHCP Setting 41
Figure 29: Cable/Dynamic IP (DHCP) 43

Figures
– 10 –
Figure 30: Static (Fixed IP) 44
Figure 31: PPPoE (ADSL) 45
Figure 32: PPTP 46
Figure 33: L2TP 47
Figure 34: Basic Radio Configuration Status 50
Figure 35: Basic Radio Configuration Dialogue Box 51
Figure 36: Advanced Radio Configuration Dialogue Box 52
Figure 37: Static Route List 57
Figure 38: Route Setting 57
Figure 39: Port Forwarding List 59
Figure 40: Port Forwarding Configuration 60
Figure 41: DMZ Configuration 61
Figure 42: Access Control List 61
Figure 43: Access Control Configuration 61
Figure 44: Access Control Time Selection 62
Figure 45: Advanced Security 62
Figure 46: Language 64
Figure 47: System Log 64
Figure 48: NTP 65
Figure 49: Password 65
Figure 50: Maintenance 66
Figure 51: Reboot your device 66
Figure 52: Resetting to Defaults 66
Figure 53: Restoring Configuration Settings 67
Figure 54: Upgrading Firmware 67