EdgeStar AP10002BL User manual

V2.2-11102017
Portable Air Conditioner
Owner’s Manual
For more information on other great EdgeStar products on the web, go to https://www.edgestar.com
To use the EdgeStar self-diagnostic tool, go to https://support.edgestar.com
AP10002BL

i
Important Safety Information
Improper handling can cause serious damage to the appliance and / or to the user.
Please read the following safety information.
Improper handling can cause serious damage to the appliance and/or to the user. Please read
the following safety information.
Electrical Safety
•
This unit is designed for indoor use only.
•
Do not use the unit in extremely humid or wet environments.
•
Do not wet the housing or control panel.
•
Do not pull the unit by the cord.
•
Always turn the unit off and unplug it from the outlet when cleaning.
•
Unplug the unit if it is not going to be used for a long period of time.
•
Do not operate the unit with a damaged plug or loose socket.
•
Use only the correct power supply with appropriate amperage.
•If the power cord is damaged, it must be replaced by the manufacturer, a service agent, or a qualified
technician.
•
Do not remove any part of the casing unless instructed to do so by an authorized technician.
General Safety
•
This portable air conditioner is not intended to be used by children.
•
Children should be supervised to ensure that they do not play with this product.
•
Do not allow children to play with the controls or drop any objects into the air outlets or vents.
•
Do not place objects or let any person sit on top of the unit.
•
Only use in the upright position on a flat, level surface and provide at least 20 inches of clearance
from any walls or objects.
•
Route the power cord carefully to avoid a tripping hazard.
•
This unit is intended for domestic use only. Do not use the portable air conditioner for industrial or
commercial use. Any other use may invalidate the warranty.

ii
Operation of Safety Plug
Your portable air conditioner is supplied with a Leakage-Current Detection and Interruption
(LCDI) safety plug. This device provides protection to reduce the risk of fire due to arcing faults in
the power supply cord. Before using your portable air conditioner, follow the instructions below to
ensure that the LCDI plug is working properly:
1. Plug the power cord into a grounded outlet.
2. Press the TEST button on the LCDI plug. This should trip the plug and cut the power to the air
conditioner. If the plug does not trip and you are able to turn on the unit, please contact
EdgeStar support.
DO NOT USE YOUR PORTABLE AIR CONDITIONER IF THE TEST FAILS.
Press the RESET button to start using your air conditioner.
DO NOT use the TEST and RESET buttons as an ON / OFF switch.
Note: Electrical products should not be disposed of with household waste. Please contact
your local recycling center for more information about how to recycle electronic waste.

1
Table of Contents
IMPORTANT)SAFETY)INFORMATION).....................................................................................................................)I!
OPERATION)OF)SAFETY)PLUG)..............................................................................................................................)II!
TABLE)OF)CONTENTS)...........................................................................................................................................)1!
INTRODUCTION)...................................................................................................................................................)2!
PARTS)IDENTIFICATION).......................................................................................................................................)3!
FRONT!VIEW!.................................................................................................................................................................!3!
BACK!VIEW!...................................................................................................................................................................!3!
BACK!VIEW!WITH!ALL!ACCESSORIES!.................................................................................................................................!4!
Parts&Included&........................................................................................................................................................&4!
Suggested&Tools&.....................................................................................................................................................&4!
WINDOW)KIT)AND)EXHAUST)HOSE)INSTALLATION)INSTRUCTIONS)......................................................................)5!
PREPARATIONS!FOR!INSTALLING!THE!WINDOW!KIT!..............................................................................................................!5!
WINDOW!KIT!INSTALLATION!INSTRUCTIONS!.......................................................................................................................!5!
INSTALLATION!OF!THE!EXHAUST!HOSE!...............................................................................................................................!8!
NOTES)ABOUT)THE)EXHAUST)HOSE).....................................................................................................................)9!
INSTALLATION)OF)THE)DRAIN)HOSE)...................................................................................................................)10!
DRAINING)THE)UNIT)..........................................................................................................................................)11!
DIRECT!DRAINAGE!.......................................................................................................................................................!11!
INSTALLING)THE)FILTER).....................................................................................................................................)12!
OPERATING)INSTRUCTIONS)...............................................................................................................................)13!
CONTROL!PANEL!OVERVIEW!..........................................................................................................................................!13!
DIRECTIONAL!LOUVERS!.................................................................................................................................................!14!
REMOTE!CONTROL!.......................................................................................................................................................!14!
INSTALLING!THE!BATTERIES!............................................................................................................................................!15!
COOLING!MODE!..........................................................................................................................................................!15!
FAN!ONLY!MODE!........................................................................................................................................................!15!
TIMER!.......................................................................................................................................................................!16!
How&to&Set&the&Unit&to&Automatically&Turn&On&....................................................................................................&16!
How&to&Set&the&Unit&to&Automatically&Turn&Off&....................................................................................................&16!
SLEEP!........................................................................................................................................................................!16!
MAINTENANCE)..................................................................................................................................................)16!
CLEANING!THE!UNIT!.....................................................................................................................................................!16!
CLEANING!THE!PRE-FILTER!.............................................................................................................................................!17!
PREPARATION!FOR!STORAGE!.........................................................................................................................................!17!
ENERGY)SAVING)GUIDE).....................................................................................................................................)18!
TROUBLESHOOTING)..........................................................................................................................................)19!
SPECIFICATIONS)................................................................................................................................................)22!
NEW)PORTABLE)AIR)CONDITIONER)BTU’S)..........................................................................................................)23!
WHAT!IS!SACC?!.........................................................................................................................................................!23!
EDGESTAR)LIMITED) WARRANTY ).........................................................................................................................)24!
!)

2
Introduction
Thank you for purchasing this EdgeStar portable air conditioner. We hope that this purchase will
be the beginning of a lasting and rewarding relationship between you and EdgeStar. We will
provide the customer support and exemplary products necessary to nurture that relationship.
This manual contains important information regarding the proper installation, use, and
maintenance of your portable air conditioner. Following this manual will ensure that your product
will work at its peak performance, efficiency, and safety.
Please save the original product packaging in case you need to safely transport your portable air
conditioner.
For Your Records:
Please write down the model number and serial number below for future reference.
Both numbers are located on the ratings label on the back of your unit and are
needed to obtain warranty service. You may also want to staple your receipt to this
manual as it is the proof of your purchase, and is also needed for service under your
warranty.
Model Number:
Serial Number:
Date of Purchase:
For a more efficient experience, please do the following before contacting customer service:
• If you received a damaged product, immediately contact the dealer that sold you the
product.
• Read and follow this instruction manual carefully to help you install, use and maintain your
portable air conditioner.
• Read the troubleshooting section of this manual as it will help you diagnose and solve
common issues.
• Visit us on the web at https://www.edgestar.com for product guides, additional
troubleshooting resources, and up-to-date information. You can also find an interactive
self-diagnostic tool at https://support.edgestar.com. If you need service, our friendly
customer service representatives are available via email at [email protected] or by
telephone at 1 [phone].

3
Parts Identification
Front View
Back View

4
Back View with All Accessories
Parts Included
Suggested Tools
Philips Screw Driver (Medium Size), Tape Measure / Ruler, Scissors, Saw (in the event that
your window panel needs to be cut down to fit your window).

5
Window Kit and Exhaust Hose Installation Instructions
Preparations for Installing the Window Kit
You must vent your portable air conditioner when running it in cooling mode. Your unit includes a
window exhaust kit that can be used to vent the unit out of a window.
Before you begin, make sure that you have all the parts necessary for installation and that a
suitable location is picked.
If you have multiple windows, choose one that is near an electrical outlet that will be able to
provide sufficient power to your unit. See the power requirements listed on the product label
printed on the side, or on the back of your portable air conditioner.
Your window kit can be installed on a horizontal or vertical sliding window as shown in the
following images.
Please follow the installation instructions carefully to avoid personal injury or damage.
Window Kit Installation Instructions
Step 1
Cut the foam seal B to the proper length and attach it to the windowsill.
Step 2
Attach the window exhaust adapter C to the window panel opening on the inside.
Note: You may need to contact your electrician if your room’s circuit is not able to power your
unit.

6
Step 3
A. If the inner width of the window is less than 28” (718 mm) wide:
1. Remove the adjustment panel from the window panel, and cut the window panel to the
same width as the window. Trim the side farthest from the exhaust opening.
2. Open the window sash and place the window panel on the windowsill.
3. Secure the window panel to the windowsill.
B. If the inner width of the window is between 28” (718 mm) and 36.5” (927 mm):
1. Open the window sash and place the adjustable window panel on the windowsill.
2. Slide the adjustment panel to fit the window frame width.
3. Secure the panel to the windowsill with four large wood screws and four slider brackets.
C. If the inner width of the window is between 36.5” (927 mm) and 64” (1625 mm):
1. Open the window sash and place the extra window panel on the windowsill.
2. Slide the adjustment panel to fit the window frame width.
3. Secure the window panel to the windowsill with four large wood screws and four slider
brackets.

7
Step 4
Cut the foam seal B to the proper length and attach it to the window panel.
Step 5
Close the window sash securely so that it is flush against the window panel.
Step 6
Cut the foam seal A to an appropriate length between the top of the inner window sash and the
outer window sash.
Step 7
Attach the bracket with a screw.

8
Installation of the Exhaust Hose
Step 1
Extend both ends of the exhaust hose and insert them into the window exhaust adapters A and
B. Turn them until they stop. Make sure they are securely attached.
Step 2
Attach the window exhaust adapter A to the unit. Insert the two projections on the window
exhaust adapter A into the two holes on the unit and firmly attach them to each other by sliding
the adapter down until it clicks. To remove the window adapter push down on the two
projections and lift up.
Step 3
Attach the hose. Insert the window exhaust adapter B to the window exhaust adapter C in the
window panel and turn it to lock it in place.

9
Notes About the Exhaust Hose
Your portable air conditioner is designed to exhaust condensed water that is collected from the air.
This water, in either gaseous or droplet form, will be expelled out of the exhaust port of the unit.
Please take this into account when deciding how to vent it.
1. The exhaust hose supplied with the portable air conditioner can be extended up to
approximately 48 inches; however, for maximum efficiency, use the shortest length
possible.
2. Try to prevent any kinks or bends in the exhaust hose. Kinks or bends may trap exhaust
air which can radiate heat into the room or potentially cause the portable air conditioner to
overheat and shut itself off.
3. The exhaust hose supplied with the portable air conditioner has been specifically designed for
this air conditioner. Do not lengthen the hose by adding additional hoses or attachments. Do
not replace it with any other hose.

10
Installation of the Drain Hose
Step 1
Remove the drain cap from the drain port.
Step 2
Attach the drain hose clamp to the back panel of the air conditioner near the drain port with the
screw.
Note: The drainage hose must be installed before using this unit. If it is not, a block in the drain
can form and prevent the unit from functioning normally.

11
Step 3
Attach one end of the drain hose to the drain port with the clip provided.
Step 4
Insert the rubber plug into the other end of the drain hose and secure clip provided.
Draining the Unit
When the portable air conditioner is in cooling mode, or dehumidify mode, it will remove moisture
from the air. The condensed water from the air will be collected in an internal reservoir and will be
evaporated and exhausted out of the exhaust hose. However, in very humid conditions, the
internal reservoir may fill completely. This causes the air conditioner to turn off to avoid
overflowing the internal reservoir. When the water tank is full a buzzer will sound eight (8) times
and the LED screen will display the error code “H8”.
Direct Drainage
1. Remove the rubber drain plug from the drain port.
2. Connect a drain hose to the drain port.
The portable air conditioner will now drain through the drain hose. Please note that this unit has
no drain pump. All water will drain with gravity only, i.e., only “downhill.”

12
Installing the Filter
Your portable air conditioner ships with a carbon filter. It is recommended you replace the filter
every two to three months, or as needed. It is also necessary to clean the pre-filter periodically
(see page 17 for maintenance instructions). Follow the steps below to install the carbon filter:
1. Shut off the unit if it is on. In the rear of the unit, pull the air filter grill out from the side.
2. Place the carbon filter between the grille and the pre-filter.
3. Close the grille.

13
Operating Instructions
Control Panel Overview
On / Off Button
Press this button once to manually turn the unit on. Press this button once
more to turn the unit off.
“+” / “-” Button
In COOL mode, press “-” once, and the set temperature will decrease by
1° Fahrenheit. Continue to press this button until you reach your desired
temperature. Press “+” to increase the temperature by 1° Fahrenheit until
you reach your desired temperature.
Mode Button
Press the MODE button repeatedly to cycle between modes: Cooling, Dry,
and Fan Only mode. The indicator light corresponding to each mode will
illuminate when that mode is selected.
The exhaust hose and window kit must be installed when the unit is in Cool
or Dry mode. It is unnecessary to have these items connected when the
unit is in Fan Only mode.
Fan Speed
When the unit is running in Cool or Fan mode, press the Fan speed button
to select your desired fan speed. There are four fan speeds: High,
Medium, Low, and Auto.
Water Full
When the unit is running in Cool or Dry mode condensation will drain to the
water reservoir. When the water tank is full a buzzer will sound eight (8)
times to indicate that the reservoir needs to be emptied. The error code
“H8” will also display on the LED screen. Follow the draining instructions
on page 11.
Louver Direction
This unit has 4-way directional louvers. Use the louver guides to direct air
where cooling or fan output is desired. Hold the louver and adjust the air
flow direction as shown in the diagram on the following page.

14
Directional Louvers
Remote Control
The included universal remote control is used to operate all of your portable air conditioner’s
functions. Use the remote control to change modes, fan speed, timer, and temperature settings as
well as to set sleep mode.
Button
Function
On / Off
This button powers the unit on or off.
Mode
This button allows you to cycle through the
following modes: Cool, Dehumidify, and Fan.
Fan
This button allows you to cycle through the
following fan speeds: automatic, Fan 1, Fan 2,
Fan 3, and Fan 4.
Swing
Swing mode is not available for this unit.
Sleep
This button is used to enable sleep mode.
Timer
This button is used to enable the timer.
Increase
This button increases the set temperature, or
the time when the Timer is enabled.
Decrease
This button decreases the set temperature, or
the time when the Timer is enabled.
Note: Be careful not to drop the remote control. Do not place the remote control in a location
exposed to direct sunlight.

15
AAA
AAA
AAA
AAA
Note: The exhaust hose must be used in cooling mode in order to cool a room.
Note: Fan Only mode does not require that the exhaust hose be attached.
Installing the Batteries
1. Remove the cover on the back of the remote control.
2. Insert the batteries with the (+) and (-) ends pointing in the direction indicated.
3. Install the cover on the back of the remote control.
Cooling Mode
Cooling mode cools and dehumidifies the air. If the ambient temperature drops below the
temperature you selected, the compressor turns off and the unit functions with the fan only. When
the temperature rises above the temperature you selected, the compressor turns on again.
Whether your desired temperature can actually be reached depends on the ambient conditions.
The room temperature remaining above the set temperature is normal.
To operate the unit in cooling mode:
1. Make sure the power cord is plugged into a power outlet.
2. Press the Power button on the remote.
3. Press the Mode button until the Mode Indicator Light on the Control Panel turns blue.
4. Select the fan speed by using the Speed button.
5. Set the thermostat by using the Up and Down buttons. The thermostat is adjustable between
61°F - 86°F in one degree increments.
Fan Only Mode
Fan Only mode is used to circulate the air in your room. No temperature setting is needed.
To operate the unit in Fan Only mode:
1. Make sure the power cord is plugged into a power outlet.
2. Press the Power button on the remote.
3. Press the Mode button until the Mode indicator light turns green.
4. Press the Speed button to select the fan speed. You can choose between High, Medium and
Low. The LED indicator next to the speed will light up.
Caution: Use only AAA batteries. Remove the batteries if the remote control will not be used for
one month or longer. Do not attempt to recharge batteries that are not designed to be recharged.
All batteries should be replaced at the same time. Do not mix old and new batteries. Do not
dispose of batteries in a fire as they may explode.

16
Timer
The timer can be used to either turn the unit on or off after a selected number of elapsed hours.
The timer is adjustable between 0.5 – 24 hours in one hour increments.
How to Set the Unit to Automatically Turn On
1. Press the Timer button on the remote control while the unit is powered off.
2. Use the Up and Down buttons on the remote to set the time (displayed in hours) you want
to pass before the unit turns on. After the selected time passes, the unit will automatically
turn on.
How to Set the Unit to Automatically Turn Off
1. Press the Timer button on the remote control while the unit is powered on. The Timer
indicator LED will light up.
2. Use the Up and Down buttons on the remote to set the time (displayed in hours). The unit
will automatically turn off after the selected time elapses.
Sleep
Press this button to turn the Sleep function on or off. When the unit is turned on the Sleep function
defaults to off, and turning the unit off automatically cancels the Sleep function. When the Sleep
function is activated, the Sleep symbol will be displayed on the LED screen. While the unit is in
Sleep mode the timer can be adjusted. The Sleep function is not available when the unit is in Fan
or Auto mode.
Maintenance
Clean the air conditioner and filters regularly to maximize performance and efficiency, and to
prolong the unit’s life. Be sure to always unplug the air conditioner from the power outlet before
cleaning.
Cleaning the Unit
Use a soft dry cloth to wipe the body of the air conditioner clean. If necessary, use lukewarm
water to dampen a cloth to clean the unit.
Use a soft bristle brush to clean between the vents.
Carefully use a vacuum cleaner to clean the condenser coils.
Never use abrasive chemicals, volatile substances, gasoline, detergents, chemically treated
cloths, or other cleaning solvents that may damage the cabinet exterior.
Warning: Never spray water directly on the unit.

17
Cleaning the Pre-filter
To clean the pre-filter, follow the steps below:
1. Power off the unit and remove the pre-filter.
2. Remove the activated carbon filter.
3. Use a vacuum cleaner or tap the pre-filter lightly to remove loose dust and dirt, then rinse the
pre-filter thoroughly under lukewarm running water (below 104°F). You may use a mild soap
and water solution if needed. Allow the pre-filter to air dry in a cool and shaded place. Dry
thoroughly before reinstalling.
Clean the pre-filter periodically. If the unit is used in a dusty environment you may need to clean it
on a weekly basis.
Preparation for Storage
If you are not going to be using the unit for an extended period of time, follow the instructions
below before storing your unit:
1. Drain all the water from the unit’s reservoir. Operate the unit in fan mode for a few hours to
thoroughly dry any moisture left on the coils inside the unit.
2. Power off the unit. Then clean or change the filters.
3. Unplug and carefully wind the power cord.
4. Remove the exhaust hose and duct connectors and keep them in a safe place.
Warning: Never operate the unit without the pre-filter.
Note: Filters should be replaced every 3 – 6 months or as needed. Contact EdgeStar or visit
www.EdgeStar.com for replacement filters.