Edgestar Ap14009com-1 User manual

V2.4-12012017

Portable Air Conditioner

Owner’s Manual

For more information on other great EdgeStar products on the web, go to http://www.edgestar.com

To use the EdgeStar self-diagnostic tool, go to https://support.edgestar.com

AP14009COM-1

Important Safety Information

Improper handling can cause serious damage to the appliance and / or to the user.

This portable air conditioner is not intended for use by children. Children should be supervised to

ensure that they do not play with this product.

Improper handling can cause serious damage to the appliance and/or to the user. Please read

the following safety information.

Electrical Safety

This unit is designed for indoor use only.

Do not use the unit in extremely humid or wet environments.

Do not spray water and wet the housing or control panel.

Do not pull the unit by the cord.

Always turn the unit off and unplug it from the socket when cleaning.

Unplug the unit if it is not going to be used for a long period of time.

Do not operate the unit with a damaged plug or loose socket.

Use only the correct power supply with appropriate amperage.

If the power cord is damaged, it must be replaced by the manufacturer, a service agent, or a qualified

technician.

Do not remove any part of the casing unless instructed to do so by an authorized technician.

General Safety

This portable air conditioner is not intended to be used by children.

Do not allow children to play with the controls or drop any objects into the air outlets or vents.

Do not place objects or let any person sit on top of the unit.

Only use the unit in the upright position on a flat, level surface and provide at least 20 inches of

clearance from any walls or objects.

Route the power cord carefully to avoid a tripping hazard.

This unit is intended for domestic use only. Do not use the portable air conditioner for industrial or

commercial use. Any other use may invalidate the warranty.

Operation of Safety Plug

Your portable air conditioner is supplied with a Leakage-Current Detection and Interruption

(LCDI) safety plug. This device provides protection to reduce the risk of fire due to arcing faults in

the power supply cord. Before using your portable air conditioner, follow the instructions below to

ensure that the LCDI plug is working properly:

1. Plug the power cord into a grounded outlet.

2. Press the TEST button on the LCDI plug. This should trip the plug and cut the power to the air

conditioner. If the plug does not trip and you are able to turn on the unit, please contact

EdgeStar support.

DO NOT USE YOUR PORTABLE AIR CONDITIONER IF THE TEST FAILS.

Press the RESET button to start using your air conditioner.

DO NOT use the TEST and RESET buttons as an ON / OFF switch.

Note: Electrical products should not be disposed of with household waste. Please contact

your local recycling center for more information about how to recycle electronic waste.

RESET

TEST

Table of Contents

IMPORTANT SAFETY INFORMATION..........................................................................................................................I

OPERATION OF SAFETY PLUG ..................................................................................................................................II

TABLE OF CONTENTS .................................................................................................................................................1

INTRODUCTION.............................................................................................................................................................2

PARTS IDENTIFICATION..............................................................................................................................................3

Front View.......................................................................................................................................................................3

Back View .......................................................................................................................................................................3

INSTALLING THE CARBON FILTER............................................................................................................................4

WINDOW KIT INSTALLATION INSTRUCTIONS..........................................................................................................5

Preparations for Installing the Window Kit......................................................................................................................5

Window Kit Parts list: ......................................................................................................................................................5

Part for Continuous Drain ...............................................................................................................................................5

Installing the Grated Adapters ........................................................................................................................................6

Installing the Window Plates...........................................................................................................................................7

Attaching the Duct Connectors to the Exhaust Hose......................................................................................................8

Connecting the Duct Connector to the Unit ....................................................................................................................9

Connecting the Duct Connector to the Grated Adapter..................................................................................................9

NOTES ABOUT THE EXHAUST HOSE......................................................................................................................10

DRAINING THE UNIT...................................................................................................................................................11

Direct Drainage.............................................................................................................................................................11

Drainage Options..........................................................................................................................................................11

REMOTE CONTROL OVERVIEW ...............................................................................................................................12

Installing the Batteries...................................................................................................................................................13

Remote Control LCD Indicators....................................................................................................................................13

Operating the Remote Control......................................................................................................................................14

FRONT PANEL LIGHTS AND CONTROLS................................................................................................................17

Front Panel Lights.........................................................................................................................................................17

Front Panel Controls

....................................................................................................................................................18

ENERGY SAVING GUIDE............................................................................................................................................18

MAINTENANCE............................................................................................................................................................19

Cleaning the Unit...........................................................................................................................................................19

Cleaning the Pre-filter ...................................................................................................................................................19

Preparation for Storage.................................................................................................................................................19

TROUBLESHOOTING..................................................................................................................................................20

SPECIFICATIONS........................................................................................................................................................22

NEW PORTABLE AIR CONDITIONER BTU’S ...........................................................................................................23

What is SACC?.............................................................................................................................................................23

EDGESTAR LIMITED WARRANTY.............................................................................................................................24

Introduction

Thank you for purchasing this EdgeStar portable air conditioner. We hope that this purchase will

be the beginning of a lasting and rewarding relationship between you and EdgeStar. We will

provide the customer support and exemplary products necessary to nurture that relationship.

This manual contains important information regarding the proper installation, use, and

maintenance of your portable air conditioner. Following this manual will ensure that your product

will work at its peak performance, efficiency, and safety.

Please save the original product packaging in case you need to safely transport your portable air

conditioner.

For Your Records:

Please write down the model number and serial number below for future reference.

Both numbers are located on the ratings label on the back of your unit and are

needed to obtain warranty service. You may also want to staple your receipt to this

manual as it is the proof of your purchase, and is also needed for service under your

warranty.

Model Number:

Serial Number:

Date of Purchase:

For a more efficient experience, please do the following before contacting customer service:

If you received a damaged product, immediately contact the dealer that sold you the

product.

Read and follow this instruction manual carefully to help you install, use, and maintain your

portable air conditioner.

Read the troubleshooting section of this manual as it will help you diagnose and solve

common issues.

Visit us on the web at http://www.edgestar.com for product guides, additional

troubleshooting resources, and up-to-date information. You can also find an interactive

self-diagnostic tool at https://support.edgestar.com. If you need service, our friendly

customer service representatives are available via email at serv[email protected] or by

telephone at 1 (866) 319-5473.

Parts Identification

Front View

Back View

Caution: Make sure the drain plug is firmly installed before using the unit to prevent leaking.

Installing the Carbon Filter

Your portable air conditioner ships with a pre-filter and an activated carbon filter. The carbon filter

will help remove contaminates and odors from the air. It is recommended that you replace the

carbon filter every two to three months, or as needed. It is necessary to clean the pre-filter

periodically. Follow the steps below to install the carbon filter.

1. Pull the handle on the pre-filter straight up.

2. Place the activated carbon filter on the pre-filter.

3. Secure the carbon filter to the pegs on the filter frame.

4. Insert the assembled pre-filter into the back of the unit.

Caution: Never operate the air conditioner without the pre-filter attached.

Window Kit Installation Instructions

Preparations for Installing the Window Kit

You must vent your portable air conditioner when running it in cooling mode. Your unit includes a

window exhaust kit that can be used to vent the unit out a window. Before you begin, make sure

you have all the parts necessary for installation.

Window Kit Parts list:

Part for Continuous Drain

Note: There is one exhaust hose connector that includes an opening for the water line for use in

the misting drain operation. This connector must be installed to the exhaust outlet on the unit.

Please review pages 9-10 for more details.

If you have multiple windows, choose one that is near an electrical outlet that will be able to

provide sufficient power to your unit. See the power requirements listed on the product label

printed on the side, or on the back of your portable air conditioner.

Your window kit can be installed on a horizontal or vertical sliding window as shown in the

following images.

Installing the Grated Adapters

1. Insert the round grated adapters through the back grooved side of the window kit plate and

into the holes.

Note: Exhaust Covers may be attached to the Grated Adapters. You may need to twist and pull

apart to separate them.

Note: You may need to contact your electrician if your room’s circuit is not able to power your

unit.

2. Secure the grated adapters by fastening the screws from the flat side of the window kit plate

to the holes on the grated adapters.

Installing the Window Plates

3. Open your window and place the window kit on the window sill with the grooved side facing

outward. Then slide the window kit plate out to fit the width of the window. You can use

screws to secure the window kit plate and keep it from sliding.

4. Lower the window to secure the window kit in place. You may need to use duct tape to better

secure the window kit. If you are not using the continuous drain option be sure the cap is

fastened to the opening between the two grated adapters to ensure heat does not enter

through the hole.

Attaching the Duct Connectors to the Exhaust Hose

5. Attach the connectors to the hose:

a. Extend the ends of the exhaust hose.

b. Thread the duct connector onto the exhaust hose by turning it clockwise until it stops.

Caution: Secure your window with window locks. Please contact your EdgeStar retailer to

purchase window locks.

6. Roll the unit towards the window kit. Leave at least 20 inches between the unit and the wall.

Connecting the Duct Connector to the Unit

7. Align the slots on the duct connector to the tabs on the unit and snap the duct connector into

the back of the unit.

Connecting the Duct Connector to the Grated Adapter

8. Align the slots on the duct connector to the tabs on the grated adapter and snap the duct

connector into place.

After you have installed the exhaust hose and the window kit, you can plug in your portable air

conditioner and start using it.

Notes About the Exhaust Hose

Your portable air conditioner is designed to exhaust

condensate

water that is collected from the

air. This water, in either gaseous

droplet form, will be expelled out of the exhaust port of the

unit.

Please take this into account when deciding how to vent

the air conditioner.

1. The exhaust hose supplied with the portable air conditioner

can

be extended up to 48 inches;

however for maximum efficiency,

use

the shortest length

possible.

2. Try to prevent any kinks or bends in the exhaust hose. Kinks

bends may trap exhaust air

which can radiate heat into the room

potentially cause the portable air conditioner to

overheat and

shut

itself

off.

The

exhaust hose supplied with the portable air conditioner

has

been specifically designed

for this air conditioner. Do not

lengthen

the hose by adding additional hoses or attachments

or replace

with any other

hose.

Warning: Longer hoses are not recommended.

Draining the Unit

When the portable air conditioner is in cooling mode, or dehumidify mode, it will remove moisture

from the air. The condensed water from the air will be collected in an internal reservoir and will be

evaporated and exhausted out of the exhaust hose. However, in very humid conditions, the

internal reservoir may fill completely. This causes the air conditioner to turn off to avoid

overflowing the internal reservoir. The WATER indicator will light up on the Control Panel.

Direct Drainage

1. Remove the rubber drain plug from the drain port.

2. Connect a drain hose to the drain port.

The portable air conditioner will now drain through the drain hose. Please note that this unit has no

drain pump; all water will drain with gravity only, i.e., only “downhill.”

Drainage Options

This portable air conditioner comes with several different options to drain water accumulated

during operation. The most common will be the self-evaporative mode. The unit will do this

automatically. This mode will be sufficient for most environments. If you are operating the unit in

an environment with higher levels of humidity you may choose the continuous drainage option to

help remove the excess water.

Continuous Drain

This unit has the capacity for continuous drainage. It includes an

internal

pump to help

remove water. The benefit is the unit will push

the

water to the drain instead of relying on

gravity for the water to

reach

the drain. If there is an obstacle in between the unit and the

drain

the pump will push the water over that obstacle through the water line. There is also

the option to run the water line through

the

window panel with the hole in between the two

grated adapters.

any method you must ensure the water line is run to a proper

drain

area that can accept and remove water. In order to

run the

continuous drain you will need to

do the

following:

1. Connect the included water line to the unit. You will need to attach the quick connect

adapter on the end of the water line to the back of the unit.

2. Place the other end of the water line (drainage end) into a drain.

The unit will recognize that the quick adapter is attached and will automatically engage the

water pump. The pump will turn on once the water reservoir becomes full.

Remote Control Overview

Button

Function

Power

This powers the unit on or off.

Fan Speed

This sets the Fan Speed. The Automatic , High , Medium , or Low

indicator light will illuminate depending on the speed you set.

Mode

This sets the mode. The Automatic , Cool , Dehumidify , or Fan

indicator will appear depending on the mode you set.

(Down)

This decreases the Temperature, Timer, or Clock settings depending on the

mode the unit is set in.

(Clock)

This is used to set the remote control clock.

Timer

This is used to enable the 24 hour timer.

C/F

This switches the temperature display between Celsius and Fahrenheit.

(Up)

This increases the Temperature, Timer, or Clock settings depending on the

mode the unit is set in.

Note: To use the remote, reach directly behind the display and pull the remote up and out to

detach it from the unit.

Installing the Batteries

1. Remove the cover on the back of the remote control.

2. Insert the batteries with the (+) and (-) ends pointing in the correct directions.

3. Slide the cover back on to the remote.

Remote Control LCD Indicators

Indicators

Function

Transmitter

This appears when the Power or Timer button is sending a signal to the

unit.

Fan Speed

This shows which fan speed is set out of Automatic , High ,

Medium , or Low .

Mode

This shows which mode is set out of the Automatic , Cool ,

Dehumidify , or Fan Only modes.

Temperature Setting

This shows the set temperature.

Fahrenheit and Celsius

This shows whether the set temperature is displayed in Fahrenheit or

Celsius.

Clock

This shows the clock’s set time. The remote control has a 24 hour

clock.

Timed Hours

This shows the number of hours the Timer is set to wait until

automatically activating.

Timer

This shows whether the On Timer or Off Timer setting is enabled.

Caution: Use only AAA batteries. Remove the batteries if the remote control will not be used for

one month or longer. Do not attempt to recharge batteries that are not designed to be recharged.

All batteries should be replaced at the same time. Do not mix old and new batteries. Do not

dispose of batteries in a fire as they may explode.

Mode Indicator

Function

Automatic

In Automatic mode, the unit will cool, dehumidify, or heat (some models)

depending on the ambient temperature. The mode and fan speed will change

automatically. The front panel lights will change to reflect the running mode.

Cool

In Cool mode the unit will cool the room. The front panel lights will illuminate

blue.

Dehumidify

In Dehumidify mode the unit will remove moisture from the air. The front panel

lights will illuminate yellow.

Fan Only

In Fan Only mode the unit will operate as a fan and circulate air. The front

panel lights will illuminate green.

Operating the Remote Control

Power

Use the Power button to turn the portable air conditioner on and

off.

By default when

you first use the Power button , the unit will begin

operate in cooling mode and the

front panel will be illuminated in

blue.

The unit will remember the last used mode / settings if

you shut down

and

restart.

Auto-Restart: If power to the unit is interrupted, the air conditioner will restart itself in its last

used mode / settings once power is restored.

The

compressor will restart after 3

minutes.

Cooling Mode

Cooling mode cools and dehumidifies the air. If the ambient

temperature

drops below the

temperature you selected, the compressor turns off

and

the unit functions with the fan only.

When the temperature rises above

the

temperature you selected, the compressor turns on

again. The front

panel

lights will be

blue.

Whether your desired temperature can actually be reached depends

the ambient conditions.

The room temperature remaining above the

set

temperature is

normal.

To operate the unit in cooling mode:

1. Make sure the power cord is plugged into a power outlet.

2. Press the Power button on the remote control.

3. Press the Mode button until the Cooling indicator is selected.

4. Select the Fan Speed by using the Fan Speed button .

5. Set the thermostat by using the Up and Down buttons. The thermostat is

adjustable between 64° F –90° F in one degree increments. You can switch between

Fahrenheit and Celsius by pressing the button.

Note: The exhaust hose must be used during Cooling mode in order to cool a room.

Dehumidifying Mode

During the Dehumidifying mode, the unit will condense water out of the air and exhaust it through

the exhaust hose. The ambient temperature in the room will probably drop by a few degrees while

using the Dehumidifying mode. The front panel lights will illuminate yellow.

To operate the unit in dehumidifying mode:

1. Make sure the power cord is plugged into a power outlet.

2. Press the Power button on the remote control.

3. Press the Mode button until the Dehumidify indicator is selected.

Fan Only Mode

Fan Only mode is used to circulate the air in your room. No temperature setting is needed. The

front panel lights will illuminate green.

To operate the unit in Fan Only mode:

1. Make sure the power cord is plugged into a power outlet.

2. Press the Power button on the remote control.

3. Press the Mode button until the Fan Only indicator is selected.

4. Press the Fan Speed button to select the Fan Speed. You can choose between

Automatic , High , Medium , or Low .

Automatic Mode

In Automatic mode, the unit will cool, dehumidify, or heat (some models) depending on the ambient

temperature. As the temperature in the room changes, the mode and fan speed will change

automatically. The front panel lights will change depending on the mode.

To operate the unit in Automatic mode:

1. Make sure the power cord is plugged into a power outlet.

2. Press the Power button on the remote control.

3. Press the Mode button until the Automatic indicator is selected.

Notes: If the room temperature is below 77° F, the fan will always run on low speed while in the

Dehumidifying mode. If you do not use the exhaust hose in Dehumidifying mode, you must

manually drain the water from the unit. Additionally, the ambient temperature in the room will

probably rise by a few degrees if you do not use the exhaust hose. You will not be able to change

the thermostat temperature while in Dehumidifying Mode.

Fan Speed

The Fan Speed button is used to change the fan speed while in Cooling and Fan Only

modes.

Press the Fan Speed button to select the fan speed. Automatic , High , Medium ,

or Low speed can be selected,

Clock

The Clock button is used to set the Clock.

To set the Clock:

1. Press and hold the Clock button until the Clock indicator starts blinking.

2. Set the time by using the Up and Down buttons. Holding down the buttons

longer than 1 second will change the time in fast mode. The clock is a 24-hour clock so if it is

6:00 pm you would set the clock time to 18:00.

3. To save your settings press and hold the Clock button until the Clock indicator stops

blinking.

12-Hour

24-Hour

1:00 pm