EdilKamin KIRA H 18 Quick start guide

EN Installation, use and maintenance page 2
KIRA H 18-22
VYDA H 18-22
PELLET BOILER STOVE

2
ENGLISH
The undersigned EDILKAMIN S.p.A., with registered office in
Via Vincenzo Monti 47 - 20123 Milan (Italy) - Tax ID Code and
VAT number 00192220192
Hereby declares, under its sole responsibility, that:
the pellet boiler stoves mentioned below are conforming with
EU Regulation 305/2011 and harmonised EU standard EN
14785:2006
PELLET BOILER STOVES, bearing the
EDILKAMIN trademark, models
VYDA H 18, VYDA H 22, KIRA H 18 and KIRA H 22
SERIAL NO.: Rating plate reference
VYDA H18, KIRA H18 : Performance declaration (DoP - EK
no. 154)
VYDA H22, KIRA H22 : Performance declaration (DoP - EK
no. 155)
Moreover, the company hereby declares that:
the wooden pellet boiler stoves VYDA H 18, VYDA H 22, KIRA
H 18 and KIRA H 22 comply with the requirements in the
following European Directives:
2014/35/EC - Low Voltage Directive
2014/30/EC - Electromagnetic Compatibility Directive
Introduction and readers of this manual 3
Safety information 4
Dimensions 5
Technical data 7
Unpacking 8
Water circuit installation 11
Terminal board 14
Installation 16
Installation of the Kira H lining 18
Installation of the Vyda H lining 24
Introduction about use 30
Display 31
Operational logic 34
Commands and Menu 37
Stand By 38
Crono 39
Temperatures 42
Ventilation, Pellet Load, Language 43
Beep, Date/Time, Pressure, Technical Menu 44
Maintenance 45
Troubleshooting 47
CONTENTS
USER/INSTALLER
The original language of this manual is Italian

3
ENGLISH
Dear Sir/Madam
We thank you for and congratulate you on choosing our
product. Before using it, we ask you to read this manual
carefully, in order for you to be able to make the most of all
its functions in total safety.
This manual is an integral part of the product. We ask you
to keep it for the entire lifetime of the product. If you lose it,
you can request a copy from your dealer or download it from
www.edilkamin.com
Readers of this manual
This manual is addressed to:
• those who will use the product at home (“USER”);
• the technician who will install the product (“INSTALLER”)
The target person of each page is indicated in a band at the
bottom of the page (USER or INSTALLER).
General information
After unpacking the product, check the condition and
completeness of the contents.
In the event of error, immediately contact the retailer where
the purchase was made, providing them with a copy of the
warranty booklet and the sales receipt.
The appliance must be installed and operated in compliance
with local and national law and European regulations. For the
installation, and for anything not specifically indicated in the
manual, observe local regulations.
The diagrams provided in this manual are for illustration
purposes only: they do not always strictly refer to your
specific model, and are not binding in any way.
MEANING OF SYMBOLS
In some parts of the manual the following symbols are
used:
INFORMATION:
failure to comply with these requirements
will compromise product use.
PLEASE NOTE:
carefully read and understand the
message in question, since failure to
follow the instructions in it could cause
serious damage to the product and put
the safety of those using it at risk.
OPERATING SEQUENCE:
follow the instructions for the operations
described.

The product is uniquely identified by a number, the
“counterfoil”, which is indicated on the warranty certificate.
Please keep:
• the warranty certificate accompanying the product
• the purchase receipt given to you by the retailer
• the declaration of conformity given to you by the installer.
The warranty conditions are given in the warranty certificate
accompanying the product.
  , in Italy, by an
authorised technician is required by UNI 10683, and is
recommended in all countries to ensure best results from
the product.
This consists of:
• checking the installation documents (declaration of
conformity) and the quality of the installation itself
• calibrating the product to suit its actual application
• providing explanations to the end user and issuing
the complementary documentation (first ignition -
commissioning certificate)
Having the appliance commissioned properly ensures that it
will operate to best effect and in complete safety.
Commissioning is required for activation of the Edilkamin
manufacturer warranty. The warranty is only valid in the
country where the product was bought.
If the appliance is not commissioned by an authorised
technician, Edilkamin will not provide warranty service. See
the warranty booklet for details. The above terms do not
affect the dealer's legal responsibility for the legal warranty.
The warranty, however, covers only demonstrable
manufacturing defects and not, for instance, problems
resulting from improper installation or calibration.
USER/INSTALLER

4
ENGLISH
SAFETY INFORMATION
• The product is not designed for use by
people, including children, with limited
physical, sensory and mental abilities.
• The appliance is not designed for
cooking purposes.
• The appliance is designed to burn
wood pellets from category A1 in the
UNI EN ISO 17225-2 standard, in the
amounts and manner described in this
manual.
• The appliance is designed for indoor
use and in areas with normal humidity
conditions.
• Keep the product in a dry place out of
the weather.
• For the legal and company warranties,
refer to the warranty certificate inside
the product: specifically, neither
Edilkamin nor the retailer are liable
for damage resulting from incorrect
installation or maintenance.
Safety risks may be caused by:
• installation in non-suitable settings,
in particular those that are subject
to fire risks. DO NOT INSTALL THE
PRODUCT IN AREAS SUBJECT TO
THE RISK OF FIRE.
• contact with fire and hot parts (e.g.
glass panel and pipes). DO NOT
TOUCH HOT PARTS and, when the
stove is switched off and still hot,
always wear the glove supplied.
• contact with live electrical equipment
(internal). DO NOT ACCESS THE
INTERNAL ELECTRICAL EQUIPMENT
WHILE THE APPLIANCE IS POWERED
ON. Electrocution hazard.
• use of improper ignition aids (e.g.
alcohol). DO NOT IGNITE OR BOOST
THE FLAME WITH FLUID SPRAYS
OR A FLAME TORCH. Serious risk of
burns, damage and injury.
• use of fuel other than wood pellets. DO
NOT BURN WASTE MATTER, PLASTIC
OR OTHER MATERIALS THAN WOOD
PELLETS IN THE COMBUSTION
CHAMBER. The product may become
soiled, the flue may catch fire, and
environmental damage may ensue.
• cleaning the combustion chamber
when hot. DO NOT CLEAN THE
HEARTH WITH A VACUUM CLEANER
WHILE IT IS HOT. You could damage
the vacuum-cleaner and risk the
emission of smoke in the room.
• cleaning the smoke duct with
cleaning products. DO NOT CLEAN
THE PRODUCT WITH FLAMMABLE
PRODUCTS. Risk of fire or blowback.
• cleaning the glass pane while hot or
with unsuitable cleaning products.
DO NOT CLEAN HOT GLASS WITH
WATER. ONLY USE RECOMMENDED
GLASS CLEANING PRODUCTS. Risk
of cracking and permanent, irreparable
damage to the glass.
• the storage of flammable materials
at a distance which is less than the
safe distances listed in this manual.
DO NOT PLACE LAUNDRY ON
THE APPLIANCE. DO NOT PLACE
DRYING RACKS WITHIN THE SAFETY
CLEARANCE. Keep flammable fluids
away from the appliance. Fire hazard.
• blocking the aeration vents and air
intakes in the room. DO NOT BLOCK
THE AERATION VENTS OR FLUE. Risk
of smoke returning into the room with
consequent damage and injury.
• use of the product as a support or
ladder. DO NOT CLIMB ONTO THE
PRODUCT OR USE IT AS A SUPPORT.
Risk of damage and injury.
• use of the stove with the combustion
chamber open. DO NOT USE THE
PRODUCT WITH ITS DOOR OPEN.
• incandescent material projected
from the open door. DO NOT throw
incandescent material outside the
appliance. Fire hazard.
• use of water in case of fire. CALL THE
AUTHORITIES if a fire breaks out.
• never operate the product without
water in the circuit.
• running it dry can damage it.
If you have doubts, please do not take
any action, but contact the retailer or the
installer.
For reasons of safety, read the user
instructions included in this manual.
USER/INSTALLER

5
ENGLISH
DIMENSIONS
VYDA H 18, VYDA H 22 (cm)
USER/INSTALLER
61.5
62
120
120
61.5
Ø 5 cm
combustion air
Ø 8 cm
smoke outlet
14
47
13
Hydraulic connections depend on the optional
kits. You can find further information in the
paragraph “water circuit installation”

6
ENGLISH
DIMENSIONS
KIRA H 18, KIRA H 22 (cm)
USER/INSTALLER
Hydraulic connections depend on the optional
kits. You can find further information in the
paragraph “water circuit installation”
Ø 5 cm
combustion air
Ø 8 cm
smoke outlet
63
65
122
122
65
14
47
13

7
ENGLISH
The above data is for guidance only and was measured during certification by a notified body.
EDILKAMIN s.p.a. reserves the right to modify the product without notification in the interests of improvement.

KIRA H 22
VYDA H 22


KIRA H 22
VYDA H 22


Nominal power Reduced power
Available power 22,5 18,7 4,9 kW
Heat output to water 20 16,3 3,8
Efficiency 92,7 93,3 95,1 %
CO emissions at 13% O20,012 0,013 0,007 %
Smoke temperature 114 101 54 °C
Fuel consumption 5,1 4,2 1,1 kg/h
Tank capacity 37 kg
Recommended draught 11 11 11 Pa
Autonomy 7 9 33 hours
Water content 20 l
Maximum operating pressure 2 bar
Maximum operating temperature 90 °C
Heatable volume * 585 485 m3
Smoke outlet diameter (male) 80 mm
Air intake diameter (male) 50 mm
Weight with packaging (Kira H) 280 kg
Weight with packaging (Vyda H ce-
ramic) 260 kg
Weight with packaging (Vyda H stone) 260 kg
TECHNICAL DATA FOR SIZING THE FLUE
which must in any case satisfy the requirements of this sheet and the installation instructions for the product
Nominal power
KIRA H 22
VYDA H 22


Smoke temperature at outlet 137 122 °C
Minimum draw 0,01 Pa
Smoke flow rate 15,1 13,4 Rps
* The heatable volume is calculated for a house insulated pursuant to Italian Law 10/91 and subsequent amendments,
and a heating demand of 33 Kcal/m³ hour.
ELECTRICAL SPECIFICATIONS
Power supply 230 V AC +/- 10% 50 Hz
Mean absorbed power 50 - 80 W
Power absorption during ignition 300 W
Protection rating Fuse 4 AT 250 V AC 5x20
TECHNICAL DATA
USER/INSTALLER

8
ENGLISH
KIRA H - VYDA H UNPACKING
PREPARATION AND UNPACKING
The packaging materials are neither toxic nor noxious
and do not require special disposal.
The user is responsible for storing, disposing of and
recycling them in a regulatory fashion.
Always move the stove in an upright
position with suitable equipment and in
observance of safety regulations.
Do not turn the package over, and handle
all parts requiring installation with care.
PACKAGING (further information in the paragraph
on linings)
The delivery consists of two packages:
• one with the structure of the boiler stove
• one  with the ceramic or stone cladding
In the boiler stove package you will find:
• warranty certificate,
• glove,
• this manual,
• power cable,
• small parts for installing the lining * (further details
on the following page),
• grille of the top,
• protective lever (removable handle) for opening
the combustion chamber door.
INSTALLER
On the top of the boiler stove there are the components described above

2
The metal grille of the top is contained in package
(1) with the boiler stove, provided with the small parts
for its installation (three M4 screws for the ceramic
parts and M6 for the stone parts, washers and rubber
buffers to be applied on top of the grille)
* Other small parts (for Vyda H and Kira H)
• M4 screws with washers for fixing the ceramic
parts
• M5 screws with washers for the ceramic sides of
Kira H
• M6 screws for fixing the stone parts
• cable glands for the terminal board on the rear
protective lever
grille of the top
THE EXHAUST PIPE TO BE CONNECTED
TO THE FUME MOTOR IS LOCATED IN THE


9
ENGLISH
KIRA H UNPACKING
INSTALLER
TO REMOVE KIRA H FROM THE PALLET
To remove the boiler stove from the pallet you must (see figures below corresponding to instructions):
1. remove the two brackets (screwed) on the front
2. remove the two brackets (screwed) on the rear of the boiler stove
TO REMOVE VYDA H FROM THE PALLET
To remove the boiler stove from the pallet you must (see figures below corresponding to instructions):
1. open the combustion chamber door; undo the two screws holding the bottom front panel and remove it to
access the two screws which fix the product to the pallet
2. remove the two brackets (screwed) on the rear of the boiler stove
DO NOT TRY TO REMOVE THE PRODUCT
FROM THE PALLET WITHOUT HAVING
OPENED THE COMBUSTION CHAMBER
DOOR AND UNDONE THE SCREWS
WHICH FIX IT TO THE PALLET
The drawings are for guidance only, useful for
the installation, but they may not refer to the
specific model.
screws fixing the product to the pallet
Pay attention in order to avoid impacts to
the panel with the display during handling
1
2
11
2

10
ENGLISH
INSTALLER
CONNECTING THE FUME EXHAUST PIPE
THE EXHAUST PIPE TO BE CONNECTED
TO THE FUME MOTOR IS LOCATED IN THE

The drawings are for guidance only, useful for
the installation, but they may not refer to the
specific model.
1. Open the lid of the pellet tank and take the pipe
2. FOR VYDA H : remove the right side panel when viewing the stove from the front. To remove it,
unscrew the two upper screws and remove it from the snap fastening below.
3. Unscrew the three screws securing the centring bracket to the back of the stove
4.Push one end out from the back of the stove and fit the pipe onto the fume motor.
Reposition and the centring bracket screw it to the back of the stove
staffa di centraggio

11
ENGLISH
WATER CIRCUIT INSTALLATION
PLUMBING
Vyda H and Kira H are provided with a closed expansion
tank.
The built-in expansion tank does NOT ensure proper
protection of the water in the entire system from thermal
expansion.
Therefore, installers should assess whether an
additional expansion tank is needed, depending on the
type of system.
ALL OTHER HYDRAULIC COMPONENTS MAY
BE INSTALLED WITHIN THE BOILER STOVE BY
PURCHASING A KIT FROM EDILKAMIN OR IF
PREPARED BY THE INSTALLER.
Plumbing depends on the type of system.
However, there are some “general rules”:
• The hydraulic system must operate at a pressure
between 1 and 1.5-2 bar at running temperature
(hot) in a closed vessel circuit.
• DO NOT install the boiler stove as a replacement in
a system with an open expansion tank.
• The presence of an accumulator (tank) is
recommended but not mandatory. Its advantage
is that it releases the boiler stove from “sudden”
requests from the system and can be integrated
with other heat sources. It reduces fuel
consumption and increases the efficiency of the
system. Edilkamin recommends an accumulator of
at least 20 l/kW.
• The return temperature of water to the boiler
stove must be higher than 50-55° C to prevent the
formation of condensation.
• An accumulator (tank) is needed to heat low-
temperature radiant panels and must be installed
according to the panel manufacturer's instructions.
• The material used in the circuit must be suitable to
withstand overheating.
• The installer must determine whether or not to use
conditioned products. In Italy, refer to UNI 8065
(Water treatment in heating systems for civil use).
• Direct plumbing to radiators prevents proper
operation, owing to the small diameter of their pipes.
Edilkamin offers four internal kits (optional)
PIPE KIT
it consists of delivery and return pipes if the other
hydraulic components are installed externally (pump,
etc.).
R KIT (specific for Vyda H and Kira H)
for installations without the production of instant
domestic hot water.
R2 KIT (specific for Vyda H and Kira H)
For installations without the production of instant
domestic hot water with system separator.
RW KIT (specific for Vyda H 22 and Kira H 22)
For installations with the production of instant domestic
hot water. Recommended for 22 kW models only.
PRESSURE GAUGE
Kira H and Vyda H are provided with an electronic
reading system for water pressure. Therefore, there is
no analogue pressure gauge. Water pressure is shown
on the display, on the bottom left (*) as indicated in
the figure below. Edilkamin proposes an analogue
pressure gauge as optional.
VENT
During normal operations the vent
is automatic. During installation, the
technician must check the functionality of
the automatic vent and assess whether a
manual vent needs to be installed.
INSTALLER
  


The product, without any kit, comes as shown in the
figure below.
G
(*)
Real size templates are available for technicians.

12
ENGLISH
WATER CIRCUIT INSTALLATION
INSTALLER
KIT R2 Template hydraulic fittings in mm
KIT R-RW Template hydraulic fittings in mm
145
183
130
160 185
73 63 70 60
73 65 105
PIPE KIT Measurements in mm
side which indicates the space occupied on the le side of the product
this line indicates the oor
HEATING DELIVERY
HEATING RETURN
SAFETY DISCHARGE
COLD H2O
THIS LINE INDICATES THE FLOOR
COLD H2O
HEATING DELIVERY
HEATING RETURN
SAFETY DISCHARGE
THIS LINE INDICATES THE FLOOR
THIS EDGE IDENTIFIES THE DIMENSION OCCUPIED BY THE PRODUCT ON THE LEFT SIDE (see the technical manual)
ONLY FOR
THIS EDGE IDENTIFIES THE DIMENSION OCCUPIED BY THE PRODUCT ON THE LEFT SIDE (see the technical manual)

13
ENGLISH
OPTIONAL HYDRAULIC KIT All kits are supplied with instructions for their connection to the boiler stove
Edilkamin technicians have a paper template suitable for each product. Make sure the correct one is used for the
product being installed.
Position the template so as to be flush with the floor and aligned with the left side of the maximum space occupied
by the boiler stove.
Be sure to respect the correct installation clearances away from flammable materials and for maintenance operations.
WATER CIRCUIT INSTALLATION
HEATING AND INSTANT DOMESTIC HOT WATER
The combinable Kits are:
• Pipe kit
• Kit R
• Kit RW
• Kit R2
The demand for heating can be made:
by the room temperature probe (if the read temperature falls 1°C below the set temperature);
by the flow switch, following the opening of the hot water tap.
The demand for heating is represented by a radiator or by a tap on the display.
HEATING AND BOILER FOR DOMESTIC HOT WATER
The Kits combinable with the boiler are:
• Pipe kit
• Kit R
The demand for heating can be made:
by the room temperature probe (if the read temperature falls 1°C below the set temperature);
by the boiler thermostat/probe demanding domestic hot water.
If there is a request for domestic hot water, the pump of the boiler stove turns on if the temperature of the boiler
stove is 5°C above the temperature of the boiler; if this happens the three-way valve deviates to the domestic water
supply. The distribution pump is off.
COMBINATION WITH ACCUMULATOR TANK
The Kits combinable with the accumulator are:
• Pipe kit
• Kit R
The accumulation probe must be set as accumulator tank probe
The demand for heating can be made:
by the thermostat/probe of the accumulator tank.
The pump of the boiler stove ensures the heat transfer from the boiler stove to the accumulator tank.
The (secondary) booster pump provides heat transfer from the accumulator tank to the system.
The timer programming on the display applies to the (secondary) booster pump.
            

INSTALLER
EXAMPLES OF HYDRAULIC INSTALLATION

     

HEATING ONLY
The combinable Kits are:
• Pipe kit
• Kit R
• Kit R2
The demand for heating can be made:
by the room temperature probe (if the read temperature falls 1°C below the set temperature).
The demand for heating is represented by a radiator on the display.

14
ENGLISH
TERMINAL BOARD
low voltage terminal board
high voltage terminal board

POLES POSSIBLE CONNECTIONS NOTES
 NTC analogue input e.g. for a second probe for accumulator tank or boiler for domestic hot water or for an external
probe for climatic curve
 NTC probe/accumulator tank thermostat
 NTC probe/room thermostat the room probe is supplied already wired as
standard

Home Automation Input.
This is an input which receives all home automation
contacts
A telephone dialler, for example
 Probe for domestic hot water boiler

POLES POSSIBLE CONNECTIONS NOTES
 Electrical connection for booster/secondary pump
(Earth, Neutral/Phase)

EXTERNAL SOLENOID VALVE (Common, Normally
Closed, Normally Open)
4 = Common
5 = Normally Closed
6 = Normally Open
During First Ignition, the technician can set up,
into parameters, the connection setting on points
4 and 5, of an external boiler contact or remore
alarm.
TERMINAL BOARD
On the rear (after having removed the protective cover
that is fixed with two screws), there is a bracket with 2
terminal boards and 5 cable glands*.
One terminal board (10 poles) is low voltage and the
other (6 poles) is high voltage. You can find some
connection examples below.
* The cable glands are included in the bag on top of
the product structure. According to the connections
needed on the terminal board, break the half-part on
the cover of the terminal board where the cable is to be
connected and block it with the cable gland.
Poles are identified with a number on the product as described below
INSTALLER

15
ENGLISH
REMARKS ON INSTALLATION
Note that:
• installation must be carried out by authorised
technical personnel;
• The appliance must be installed and operated
in compliance with local and national law and
European regulations. The applicable Italian
standard is UNI 10683;
• If installed in a condominium, the appliance must
be approved by the administrator.
We give some general instructions below, however
these do not obviate the need to comply with local
regulations and do not imply any liability as regards
the installer's work.


• The room must have a volume of at least 15 m3.
• The floor must be able to bear the weight of the
product and its accessories.
• Level the product (the product is provided with
adjustable feet).
• The appliance may not be installed in a bedroom,
bathroom or in the same room as other equipment
which draws air for combustion from the room
itself, or in any area with an explosive atmosphere.
Any extraction fans operating in the same room or
area as the product, may affect its draw.
• In Italy, check the compatibility pursuant to UNI
10683 and UNI 7129 in the presence of gas fired
products.
INSTALLATION

The surfaces of the building that are adjacent to the
product must be protected against overheating.
The insulation to be used will depend on the type of
surface in question.
The appliance must be installed in accordance with
the following safety instructions:
- no flammable materials may be kept closer than 15
cm to the sides and back
- no flammable materials may be kept within 80 cm
from the front of the appliance.
If connected to a wooden or otherwise flammable wall,
the flue must be insulated appropriately.
If installed on a flammable or combustible floor, or
which is not capable of bearing its load, use steel or
glass plates under the stove to distribute the load.

The product is designed to operate in all climatic
conditions. In special circumstances, such as strong
wind, its safety equipment may switch the appliance
off.
Contact the authorised Edilkamin Technical Assistance
Centre.
INSTALLER
ADJUSTABLE FEET
The boiler stoves (Kira H and Vyda H) are provided
with adjustable feet for better positioning on the floor.
The feet are adjustable in height using a screwdriver
at the top of the foot and can slightly raise the boiler
stove.
feet

16
ENGLISH
FLUE SYSTEM(   

This chapter has been drawn up pursuant to European
standards EN 13384, EN 1443, EN 1856 and EN 1457.
The installer must observe both these and any other
local regulations.
This manual does not in any way substitute such
regulations.
The product must be connected to a flue system which
ensures that the smoke produced by combustion is
discharged in complete safety.
Before positioning the appliance, the installer must
check that the flue is suitable.

The smoke duct (which connects the smoke outlet of
the combustion chamber with the flue) and the flue
itself must, among other regulatory requirements:
• receive the smoke from a single product (outlets
from multiple appliances may not be conveyed
into a single flue)
• be routed vertically for the most part
• have no downwards sloping sections
• preferably have a circular internal cross section, or
with a ratio of the sides of less than 1.5
• terminate at roof level with a proper chimney pot:
the flue may not discharge directly onto the wall
or into an enclosed space, even if the space in
question is open to the sky
• be made of material with rated fire reaction class
A1 as per UNI EN 13501 or analogous national
regulations
• be certified, with a chimney plate if metal
• be of uniform cross section or vary in cross section
only immediately after the outlet, not at some mid
point of its length
THE SMOKE DUCT
Further to the general prescriptions for the smoke duct
and flue, the smoke duct:
• may not be made of flexible metal material
• must be insulated, if routed through unheated
areas or outdoors
• must not be routed through rooms where the
installation of combustion heat generators is
prohibited, where there is risk of fire, or which
cannot be inspected
• must enable the recovery of soot and be open for
inspection
• must have at most 3 bends with a maximum angle
of 90°
• if there is a horizontal section, it must be a single
one with a maximum length of no more than 3
metres, depending on the draw. Note, in any case,
that long sections promote the accumulation of
dirt and are harder to keep clean.
INSTALLATION
INSTALLER

17
ENGLISH
THE FLUE:
Further to the general prescriptions, the flue must
• only be used to discharge smoke
• be correctly sized to satisfy the requirements of
smoke discharge (EN 13384-1)
• must preferably be insulated, in steel with a circular
internal section. If rectangular, the corners must
have a radius of not less than 20 mm, with a ratio
of the internal dimensions of <1.5
• must normally be at least 1.5 metres in vertical
length
• must have a constant cross section
• must be waterproof and thermally insulated to
ensure a good draw
• must preferable have a collection chamber for
non-combusted matter and condensation.
• if pre-existing, it must be cleaned to prevent any
fire hazard
• in general, we recommend fitting a tube inside the
existing masonry chimney if its diameter is greater
than 150 mm. This recommendation is purely for
guidance; the installer must assess wile installing,
after the calculation of the draw.
INTUBATED SYSTEM:
Further to the general prescriptions, the intubated
system must:
• operate in negative pressure
• be open to inspection
• be compliant with local regulations.
THE CHIMNEY POT must:
• be wind-proof
• have an internal cross section equivalent to that of
the flue and a smoke outlet at least double that of
the interior of the flue
• extend beyond the back flow zone (in Italy, refer to
UNI 10683 point 6.5.8.)
• allow for maintenance of the chimney
For dual flues (which should be spaced at least 2 m
apart), the chimney pot receiving the smoke from the
solid fuel appliance or that from the higher storey, must
be at least 50 cm higher than the other
AIR INTAKE FOR COMBUSTION
In general, we suggest two ways to ensure a proper
flow of combustion air. Air must come from the outside*
It is also important to ensure a change of heating air
and glass cleaning air etc.

The boiler stove takes air from the outside through the
hole on the rear.
Install an air outlet at floor level with an effective sur-
face area (net of the mesh or other protections) of at
least 80 cm2(10 cm in diameter).
To prevent draughts, we recommend installing the
intake behind the product or behind a radiator.
Installing it in front of the appliance will create
unpleasant draughts.

Install an air intake of effective area (net of the mesh or
other protective equipment) at least equal to that of the
air intake at the back of the product.
Connect the air intake to the appliance's air intake with
a tube (which may also be of the hose type). Increase
the diameter of the pipe if it is not smooth: assess its
pressure drops.
We recommend not exceeding a length of 3 m,
considering the draw of the flue. For each curve, up
to a maximum of two, the length must be reduced by
1 m. You should also consider increasing the diameter
of the pipe.
*The air may be drawn from an adjacent room only if:
• the flow is taken from permanent and unobstructed
openings communicating with the outdoors
• the air pressure in the adjacent room is never
lower than that of the outdoor pressure
• the adjacent room is not a garage. subject to fire
hazard, a bathroom or bedroom
• the adjacent room is not a shared room in the
condominium
In Italy, UNI 10683 provides that ventilation is sufficient
even if a pressure difference between the outdoors
and indoors of no more than 4 PA is guaranteed (UNI
EN 13384-1). The installer who issues the declaration
of conformity is responsible for ensuring these
conditions.
**The direct connection of the air intake does not
make the product airtight. It is therefore necessary also
to ensure recovery of the air taken in the room by the
product (i.e. for the glass cleaning)
INSTALLATION
INSTALLER

18
ENGLISH
CHECKING THE ELECTRICAL


The product is supplied with an electrical power cord
for connection to a 230V 50 Hz socket, preferably one
equipped with a trip switch.
Variations in voltage of more than 10% can compromise
its operation.
The electrical system must be compliant; check the
operation of the earth in particular.
Edilkamin is not responsible for malfunctions resulting
from an improperly earthed system.
The power line must be of adequate section for the
power of the appliance.
The power cable must not come into contact with the
flue or other hot parts of the stove.
Power up the product by setting its switch from 0 to 1.
There is one 4 A fuse on the socket with switch located
at the rear of the product.
INSTALLATION
switch
fuse housing power supply
INSTALLER

19
ENGLISH
KIRA H- LINING
  
Bottom front panel  no.1
Top front panel  no.1
Top right ceramic side  no.1
Lower right ceramic side  no.1
Lower left ceramic side  no.1
Top left ceramic side  no.1
Ceramic top  no.1
INSTALLER
The position of each ceramic side is indicated on the interior part of each piece (example BTM. RH.)
The metal grille of the top is in the package of the stove structure together with the M4 screws, fixing washers and the
two rubber buffers to be applied on top of the grille
* Small parts to be used for Kira H:
• M4 screws with washers for fitting the ceramic front parts
• M5 screws and washers for fitting the ceramic sides
• cable glands for the terminal board on the rear



2

2
3

3



20
ENGLISH
KIRA H- LINING
INSTALLER
1. Open the combustion chamber door with the
protective lever (removable handle P) and undo two
screws to remove the bottom metal front panel
2. Fit the ceramic part on the bottom metal front panel
using the M4 screws with washers

P
3. Screw the bottom metal front panel - (with the
bottom ceramic front panel already fitted) to the stove.
You can adjust the position of the front panel horizontally
to align it to the door, by moving the screws in the slots
1


1
2
3
Do not force the screw into the pin, it may
break