EdilKamin MITO IDRO Quick start guide

MITO IDRO
EN Installation, use and maintenance page 2
PELLET BOILER STOVE

2
ENGLISH
Safety Information 4
General information 5
Installation 11
Covering Installation 15
Instructions for use 19
Maintenance 24
Possible troubleshooting 26
The undersigned EDILKAMIN S.p.a. with head office he-
adquarters at Via Vincenzo Monti 47 - 20123 Milan - Italy - VAT
IT00192220192
Declares under its own responsability as follows:
The pellet Boiler-stoves illustrated below conforms to Regu-
lation EU 305/2011 (CPR) and to the harmonised European
Standard
EN 14785:2006
WOOD PELLET BOILER-STOVES, trademark EDILKAMIN,
called MITO IDRO
Year of manufacture: Ref. Data nameplate
Declaration of performance (DoP - EK n° 129):
Ref. data tag plate
In addition, it is hereby declared that:
The wood pellet Boiler-stoves MITO IDRO is in compliance
with the requirements of the European directives:
2014/35/CE - Low voltage directive
2014/30/CE - Electromagnetic compatibility directive
EDILKAMIN S.p.a. will decline all responsability of malfun-
ctioning or damage to the equipment in case of unauthori-
zed
substitution, assembly or modifications of any sort on the
said equipment on the part of non-EDILKAMIN personnel.
CONTENTS

3
ENGLISH
Dear Sir/Madam
We thank you for and congratulate you on choosing our
product. Before using it, we ask you to read this manual
carefully, in order for you to be able to make the most of all
its functions in total safety.
This manual is an integral part of the product. We ask you
to keep it for the entire lifetime of the product. If you lose it,
you can request a copy from your dealer or download it from
www.edilkamin.com
Readers of this manual
This manual is addressed to:
• those who will use the product at home (“USER”);
• the technician who will install the product (“INSTALLER”)
The target person of each page is indicated in a band at the
bottom of the page (USER or INSTALLER).
General information
After unpacking the product, check the condition and
completeness of the contents.
In the event of error, immediately contact the retailer where
the purchase was made, providing them with a copy of the
warranty booklet and the sales receipt.
The appliance must be installed and operated in compliance
with local and national law and European regulations. For the
installation, and for anything not specifically indicated in the
manual, observe local regulations.
The diagrams provided in this manual are for illustration
purposes only: they do not always strictly refer to your
specific model, and are not binding in any way.
MEANING OF SYMBOLS
In some parts of the manual the following symbols are
used:
INFORMATION:
failure to comply with these requirements
will compromise product use.
PLEASE NOTE:
carefully read and understand the
message in question, since failure to
follow the instructions in it could cause
serious damage to the product and put
the safety of those using it at risk.
OPERATING SEQUENCE:
follow the instructions for the operations
described.
Identification of the product and warranty.
The product is uniquely identified by a number, the
“counterfoil”, which is indicated on the warranty certificate.
Please keep:
• the warranty certificate accompanying the product
• the purchase receipt given to you by the retailer
• the declaration of conformity given to you by the installer.
The warranty conditions are given in the warranty certificate
accompanying the product.
First ignition (commissioning), in Italy, by an
authorised technician is required by UNI 10683, and is
recommended in all countries to ensure best results from
the product.
This consists of:
• checking the installation documents (declaration of
conformity) and the quality of the installation itself
• calibrating the product to suit its actual application
• providing explanations to the end user and issuing
the complementary documentation (first ignition -
commissioning certificate)
Having the appliance commissioned properly ensures that it
will operate to best effect and in complete safety.
Commissioning is required for activation of the Edilkamin
manufacturer warranty. The warranty is only valid in the
country where the product was bought.
If the appliance is not commissioned by an authorised
technician, Edilkamin will not provide warranty service. See
the warranty booklet for details. The above terms do not
affect the dealer's legal responsibility for the legal warranty.
The warranty, however, covers only demonstrable
manufacturing defects and not, for instance, problems
resulting from improper installation or calibration.

4
ENGLISH
SAFETY INFORMATION
• The product is not designed for use by
people, including children, with limited
physical, sensory and mental abilities.
• The appliance is not designed for
cooking purposes.
• The appliance is designed to burn
wood pellets from category A1 in the
UNI EN ISO 17225-2 standard, in the
amounts and manner described in this
manual.
• The appliance is designed for indoor
use and in areas with normal humidity
conditions.
• Keep the product in a dry place out of
the weather.
• For the legal and company warranties,
refer to the warranty certificate inside
the product: specifically, neither
Edilkamin nor the retailer are liable
for damage resulting from incorrect
installation or maintenance.
Safety risks may be caused by:
• installation in non-suitable settings,
in particular those that are subject
to fire risks. DO NOT INSTALL THE
PRODUCT IN AREAS SUBJECT TO
THE RISK OF FIRE.
• contact with fire and hot parts (e.g.
glass panel and pipes). DO NOT
TOUCH HOT PARTS and, when the
stove is switched off and still hot,
always wear the glove supplied.
• contact with live electrical equipment
(internal). DO NOT ACCESS THE
INTERNAL ELECTRICAL EQUIPMENT
WHILE THE APPLIANCE IS POWERED
ON. Electrocution hazard.
• use of improper ignition aids (e.g.
alcohol). DO NOT IGNITE OR BOOST
THE FLAME WITH FLUID SPRAYS
OR A FLAME TORCH. Serious risk of
burns, damage and injury.
• use of fuel other than wood pellets. DO
NOT BURN WASTE MATTER, PLASTIC
OR OTHER MATERIALS THAN WOOD
PELLETS IN THE COMBUSTION
CHAMBER. The product may become
soiled, the flue may catch fire, and
environmental damage may ensue.
• cleaning the combustion chamber
when hot. DO NOT CLEAN THE
HEARTH WITH A VACUUM CLEANER
WHILE IT IS HOT. You could damage
the vacuum-cleaner and risk the
emission of smoke in the room.
• cleaning the smoke duct with
cleaning products. DO NOT CLEAN
THE PRODUCT WITH FLAMMABLE
PRODUCTS. Risk of fire or blowback.
• cleaning the glass pane while hot or
with unsuitable cleaning products.
DO NOT CLEAN HOT GLASS WITH
WATER. ONLY USE RECOMMENDED
GLASS CLEANING PRODUCTS. Risk
of cracking and permanent, irreparable
damage to the glass.
• the storage of flammable materials
at a distance which is less than the
safe distances listed in this manual.
DO NOT PLACE LAUNDRY ON
THE APPLIANCE. DO NOT PLACE
DRYING RACKS WITHIN THE SAFETY
CLEARANCE. Keep flammable fluids
away from the appliance. Fire hazard.
• blocking the aeration vents and air
intakes in the room. DO NOT BLOCK
THE AERATION VENTS OR FLUE. Risk
of smoke returning into the room with
consequent damage and injury.
• use of the product as a support or
ladder. DO NOT CLIMB ONTO THE
PRODUCT OR USE IT AS A SUPPORT.
Risk of damage and injury.
• use of the stove with the combustion
chamber open. DO NOT USE THE
PRODUCT WITH ITS DOOR OPEN.
• incandescent material projected
from the open door. DO NOT throw
incandescent material outside the
appliance. Fire hazard.
• use of water in case of fire. CALL THE
AUTHORITIES if a fire breaks out.
• never operate the product without
water in the circuit.
• running it dry can damage it.
If you have doubts, please do not take
any action, but contact the retailer or the
installer.
For reasons of safety, read the user
instructions included in this manual.

5
ENGLISH
maschio 1/2"
Ø 8 cm
uscita fumi
Ø 4 cm aria
combustione
55
52
110
55
110
52
18,5
44
12
1,5
7
879,5
maschio 3/4"
10
maschio 1/2"
Ø 8 cm
uscita fumi
Ø 4 cm aria
combustione
55
52
110
55
110
52
18,5
44
12
1,5
7
879,5
maschio 3/4"
10
maschio 1/2"
Ø 8 cm
uscita fumi
Ø 4 cm aria
combustione
55
52
110
55
110
52
18,5
44
12
1,5
7
879,5
maschio 3/4"
10
maschio 1/2"
Ø 8 cm
uscita fumi
Ø 4 cm aria
combustione
55
52
110
55
110
52
18,5
44
12
1,5
7
879,5
maschio 3/4"
10
Combustion air
Ø 40 mm
Smoke outlet Ø
80 mm
3/4” male
1/2” male
inlet
outlet
DIMENSIONS
MITO IDRO dimensions (cm)

6
ENGLISH
ELECTRICAL CHARACTERISTICS
Power supply 230Vac +/- 10% 50 Hz
Average power consumption 120 W
Power consumption during ignition 400 W
Protection on electronic circuit board T2A, 250 Vac, 5x20 Fuse
TECHNICAL DATA FOR SIZING THE FLUE
which must in any case satisfy the requirements of this sheet and the installation instructions for the product
Nominal power Reduced power
Thermal power output 13 3,9 kW
Temperature of fumes on exit from the discharge
pipe 155 67 °C
Minimum draught 0 - 5 Pa
Fume flow capacity 10,6 3,6 g/s
TECHNICAL DATA as per EN 14785
Nominal power Reduced power
Thermal power output 13 3,9 kW
Thermal power transferred to the water without fan 10 3 kW
Thermal power transferred to the environment 3 0,9 kW
Yield / Efficiency 91,6 97,6 %
Emissions CO 13% O20,010 0,025 %
Fume temperature 129 56 °C
Fuel consumption 3 0,8 kg/h
Draught 12 - 5 10 - 3 Pa
Hopper capacity 30 kg
Water content 12 Litres
Maximum operating pressure of the water 1,5 bar
Maximum operating temperature of the water 90 °C
Autonomy 9 34 hours
Heatable volume * 340 m3
Smoke outlet pipe diameter (male) 80 mm
Air intake pipe diameter (male) 40 mm
Weight including packaging (ceramic/steel) 250 / 230 kg
* The heatable room dimensions are calculated on the basis of home insulation in compliance with Italian law 10/91,
and subsequent changes together with an expected heat output of 33 Kcal/m³ per hour.
TECHNICAL DATA
The above data is for guidance only and was measured during certification by a notified
body.
EDILKAMIN s.p.a. reserves the right to modify the product without notification in the
interests of improvement.

7
ENGLISH
DISIMBALLO
PREPARAZIONE E DISIMBALLO
I materiali che compongono l’imballo non sono né
tossici né nocivi, pertanto non richiedono particolari
processi di smaltimento.
Lo stoccaggio, lo smaltimento o eventualmente il
riciclaggio è a cura dell’utilizzatore finale in conformità
delle vigenti leggi in materia.
IMBALLO
L’imballo contiene due colli:
- uno (1)con la struttura della stufa;
- uno (2) con le ceramiche
Di seguito la descrizione per la versione in ceramica e
per la versione in acciaio
Si raccomanda di effettuare ogni
movimentazione in posizione verticale con
mezzi idonei prestando attenzione alle
norme vigenti in materia di sicurezza.
Non rovesciare l’imballo e usare ogni
cautela per i particolari da montare.
versione in ceramica versione in acciaio
1
2
1
2
DISIMBALLO
Per rimuovere il prodotto dal bancale:
• smontare il frontalino inferiore;
• svitare le viti di fissaggio al bancale
• riposizionare il frontalino
Il materiale dell’imballo (per esempio plastiche, fogli a
pellicola) può essere pericoloso per i bambini.
C’è rischio di soffocamento. Tenere gli imballaggi
lontano dai bambini.

8
ENGLISH
1) CERAMIC VERSION
Fig. 1
The stove is delivered (Fig. 1) with the following external
components already installed:
• aluminium profiles (A)
• upper grille (B)
• lower panel (C)
The pieces indicated below are packaged separately.
• 6 side ceramic panels (D)
• 1 lower horizontal ceramic element (E)
• 1 upper horizontal ceramic element (F)
• 1 ceramic top (G)
• 4 milled pins M4
• 4 washers
• 4 rubber stoppers (M)
• 4 flat washers D 10
• 4 brass washers D 8
To fit proceed as follows:
Fig. 2
Remove the upper grille together with the frame (B)
screwed onto the structure and the interlocking lower
panel (C), after removing the fixing screw.
Fig. 3
Attach the lower horizontal ceramic element (E) using
the relevant slots, M4 knurled bolts and washers provi-
ded.
fig. 1
A
B
A
C
fig. 3
E
C
B
fig. 2
fixing screw
detail of upper
grille attachment to
the structure
COVERING INSTALLATION

9
ENGLISH
Fig. 4
Attach the upper horizontal ceramic element (F) to the
upper grille (B) using the two M4 knurled bolts and wa-
shers provided.
Fig. 5
Insert the side ceramic panels (D) into the relevant
guides.
N.B.
In the event of vibration, an 8x1 adhesive gasket is
provided
to place between the profi les and ceramic side panels.
Fig. 6
Place the ceramic top (G) above the structure.
NB: it the ceramic top does not fit evenly
over the structure, use the rubber stoppers
(M) and washers provided, inserting them
into the housings on the cast iron top.
fig. 6
fig. 5
G
D
D
D
fig. 4
B
F
REAR VIEW
MM
COVERING INSTALLATION

10
ENGLISH
fig. 1
2) STEEL VERSION
Fig. 1
The stove is delivered (Fig. 1) with the following external
components already installed:
• metal sides (A)
• upper grille (B)
• lower panel (C)
The pieces indicated below are packaged separately.
• 1 lower horizontal ceramic element (E)
• 1 upper horizontal ceramic element (F)
• 1 ceramic top (G)
• 4 milled pins M4
• 4 washers
• 4 rubber stoppers (M)
• 4 flat washers D 10
• 4 brass washers D 8
To fit proceed as follows:
Fig. 2
Slide out the metal sides upwards to remove the upper
grille together with the frame (B) screwed onto the struc-
ture and the interlocking lower panel (C),
After removing the fixing screw. Re-position the pre-
viously removed metal sides.
Fig. 3
Attach the lower horizontal ceramic element (E) using
the relevant slots, M4 knurled bolts and washers provi-
ded.
fig. 3
A
B
C
E
C
B
fig. 2
fixing screw
detail of upper
grille attachment to
the structure
COVERING INSTALLATION