Egholm Park Ranger 2150 User manual

3in1All Year
Operation
Cost Saving
Park Ranger 2150
BASIC MACHINE
OperatOr’smanual

2Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
Dear Customer,
Congratulations with your Egholm product
The Park Ranger 2150 is a Danish designed and manufactured utility machine, which allows you
to take a very exible approach to maintaining outdoor areas.
Optimal use of your Park Ranger 2150 utility machine:
To ensure optimal performance from your Park Ranger 2150 utility machine, please read this
manual carefully before using the machine. Failure to do so can result in personal injury and
damage to the machine.
Safety:
The utility machine is equipped with various devices to ensure optimal operational safety both
for the user and for the surroundings. We ask you to pay particular attention to section 1.1 Safety.
The machine must only be serviced by professionals.
The utility machine is designed for professional use only. On delivery, the user will receive
thorough training to become a competent operator.
Do not lend the machine to anyone who has not been thoroughly trained and has not read this
manual carefully.
The operator’s manual should be considered a vital accessory to the utility machine and so must
remain with it if the machine is sold.
Warnings:
Some items in this operator’s manual are marked with this warning symbol.
The warning indicates areas where extra care has to be taken to avoid personal
injury or damage to the machine and its accessories. The warning also explains
how you should pay special attention to the aspect in question.
Reservations:
As it is the Egholm policy to make continuous improvements, we reserve the right to alter the
specications and equipment at any time without notice.
Egholm accepts no liability for errors or shortcomings in the operator’s manual.
Contact Egholm
Should you have any questions regarding your Egholm product, do not hesitate to contact
Egholm.
Best regards
Egholm A/S · Transportvej 27 · DK-7620 Lemvig
T. [phone] · F. [phone]
E-mail: [e-mail] · www.egholm.eu
!
Introduction

3
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
General information..............................................................................5
1.1 Safety ....................................................................................5
1.2 EC Declaration of Conformity.................................................................7
1.3 Technical data .............................................................................8
1.4 Steering column...........................................................................10
1.5 Operating levers and pedals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1.6 Fitting a cab (optional) .....................................................................15
1.7 Operating panel, cab (optional)..............................................................16
1.8 Removable load carrier (optional)............................................................17
1.9 Driver’s seat ..............................................................................18
1.10 Oil cooler cover...........................................................................18
1.11 Fuses and main switch ....................................................................19
Operator’s manual ..............................................................................20
2.1 Daily checks before start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2.2 Starting, operation and stopping ............................................................22
Service and Maintenance.........................................................................24
3.1 Daily maintenance.........................................................................24
3.2 Lubrication ...............................................................................25
3.3 Service and maintenance chart for the Park Ranger 2150........................................26
3.4 Hydraulic system ..........................................................................28
3.5 Engine maintenance .......................................................................29
3.6 Fuel .....................................................................................31
3.7 Radiator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
3.8 Air lter..................................................................................34
3.9 Battery ..................................................................................34
3.10 Fan belt .................................................................................35
3.11 Articulated joint..........................................................................35
Conditions .....................................................................................36
4.1 Warranty.................................................................................36
4.2 Complaints ...............................................................................37
4.3 Disposal..................................................................................37
Wearing parts ..................................................................................38
5.1 Wearing parts – Park Ranger 2150...........................................................38
Notes .........................................................................................41
Contents

4Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
The Park Ranger 2150 utility machine
The Park Ranger 2150 is an Egholm utility machine with a complete range of special attachments
designed to allow you to perform outdoor maintenance work all year round. Sweeping and
vacuuming in spring and autumn, mowing grass and lawn-edge cutting in the summer, and
sweeping snow, and spreading gravel and sand in the winter.
Easy attachment changeover
Attachments can be changed quickly and easily in less than four minutes.
Introduction

5
1
2
3
4
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
1.1 Safety
Make sure no-one is standing close to the
machine while it is in use:
Make sure that no one is near the machine
while it is in use as there is a danger of
crushing.
NB:
As it is articulated, the rear end of the machine
swings out when turning. Make sure that no
one is standing near the machine while it is in
use. (Picture 1)
Turn the steering wheel carefully:
The Park Ranger 2150 is articulated and the
steering mechanism is extremely responsive.
(Picture 2)
Avoid accidents with battery acid and
gases:
Batteries contain explosive gases and acid.
Please take the greatest care when handling
batteries. (Picture 3)
Avoid accidents with exhaust fumes:
Exhaust fumes can cause illness or even death.
If the engine is to run in an enclosed room, the
exhaust fumes must be led outside – using
an exhaust hose, for example. If there is no
ventilation system in the room, the doors and
windows must be left open to allow fresh air
to enter.
Avoid roll-overs:
Do not drive the machine in places where
there is a risk that it may slide, tip or roll. Do
not drive on slopes with an incline of more
than 10°. (Picture 4)
Keep children away from the machine when the engine
is running.
!
!
!
!
!
!
Battery
Prevent people from standing in the working area
Articulated joint
General information
Do not drive on slopes with an incline of more than 10°
Max. 10°

6
1
2
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
Avoid crushing ngers:
Keep your hands and ngers away from areas where there
is a danger of crushing.
The A-frame
Take care not to catch your ngers in the A-frame for the
various tools. (Picture 1)
Exhaust pipe
Make sure not to touch the exhaust pipe as this becomes
very hot when the machine is operating. (Picture 2)
The Engine
Caution! All components in the Engine can become very
hot!
Fan belt
Make sure not to catch your ngers in the fan or the fan
belt. (Picture 2)
General information
Avoid crushing ngers
Exhaust pipe Fan

7
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
General information
1.2 EC Declaration of Conformity
Manufacturer: Egholm A/S
Address: Transportvej 27 · DK-7620 Lemvig
Telephone: [phone]
hereby declares that
The machine: Park Ranger 2150
Type: UHM 2150A0 XX (year of manufacture)
A XXXXX (serial number)
· has been manufactured in conformity with Directive 2006/42/EU
Place: Lemvig
Date:
Signature:
Knud Olsen, Senior Engineer

8Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
1.3 Technical data
General information
Dimensions:
Length (L) 2,225 mm
Width (W) 1,015 mm
Height with cab 1,935 mm
Height without cab 1,210 mm
Max. speed 16 km/h
Weight
Weight 485 kg
Max. permitted weight for:
Utility machine 1,300 kg
Machine and trailer without brakes 1,750 kg
Machine and trailer with overrunning brakes 2,650 kg
Trailer without brakes 750 kg
Trailer with overrunning brakes 1,500 kg
Permitted axle load, front 740 kg
Permitted axle load, rear 740 kg
Tyres:
Tyre size 18 x 9.5-8
Tyre pressure 1.6 bar or 24 psi
Motor:
Type/manufacturer Perkins Diesel
Type 403D-11
Motor power 28 hp or 21 kW at 3,400 rpm
Cylinders 3
EU Norm Stage lllA
Please refer to the engine operator’s manual for additional technical data
Fuel:
Fuel Diesel
Fuel tank capacity 20 l diesel
At 2,400 rpm approx. 2.8 l/h
At 3,400 rpm approx. 4.6 l/h

9
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
Lubricating system:
Lubricating system Pressure-lubricating system with lter
Lubricants Motor oil: approx. 3 l, synthetic 5W-40 API CF, CF-4, CG-4, CH-4
Air lter Dry, replaceable element lter
Cooling system Liquid coolant
Electrical system:
Starter system Electric starter with glow plugs
Charging system Generator
Charging capacity 12 volt, 65 amp
Battery 12 Volt, 44 AH
Hydraulic oil:
Hydraulic oil, type Texaco Rando HDZ 68
Tank capacity 15 l
Working pressure Up to 180 bar
Brakes
Operating brakes Hydrostatic
Parking brakes Mechanical
Sound measurements:
Running, Directive 2009/63/EF 78 dB(A)
Pass-by, Directive 2009/63/EF 80 dB(A)
Machine operator position, open windows, 2009/76/EF 85 dB(A)
Machine operator position, closed windows, 2009/76/EF 84 dB(A)
Vibration test:
Whole body, EN 13059 0.6 m/s2
Hand/arm, EN 13059 2.4 m/s2
Turning radius:
Park Ranger 2150 has an extremely small turning radius 1.5 m
Information plate:
Mounted on the right side of the front chassis.
Attention:
Specications may change without notice.
General information

10
4 51 72 63
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
General information
1.4 Steering column
1. Hazard lights
2. Timer
3. Load control lamp
If this symbol lights up at any time other than during ignition, stop the engine and identify the cause.
4. Pre-heater indicator
Does not light up together with the three other warning lights. It does not light up until the key has been
turned to “pre-heating” position. When the light goes out, turn the key to the next position to start the
machine.
5. Switch – electrical socket
6. Oil pressure warning light. If this lamp lights up during operation, stop the machine immediately, switch o
the engine and check the oil level. Rell immediately if the oil level is low.
7. Overheating warning light. This light is not lit when the coolant temperature is normal.
If this light comes on, the engine temperature is too high. Switch o all the attachments and leave the
engine to run at half power (i.e. half revolution speed) for approx. 2 minutes. If necessary, clean the radiator
grilles.

11
11 138 9 1210
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
Generel information
1.4 Steering column - continued -
8. Indicator switch/stalk
9. Throttle. When starting the machine, pull the throttle open to approx. 1/4 of its capacity. It is then easy to
start the engine.
10. Fuel control light. Comes on when 5 litres remain in the tank – sucient for approx. 1½ hours’ operation. This
light is only lit when the machine is switched on.
11. Horn
12. Ignition key
13. Fuses. See Section 1.11

12
1
1
2
3
C1
A B C B1B2
C2
1
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
General information
1.5 Operating levers and pedals
1. Lever A (Picture 1)
For raising and lowering front-mounted attachments on the
A-frame:
Top position: Raises the attachment
Middle position: Locks the attachment in a given
position
Bottom position: Lowers the attachment
2. Lever B (Picture 1)
Activation of hydraulic connectors B1 and B2 – for attachments.
Pos. 1: Locked – oil ow activated = attachment
operating
Pos. 0: Neutral (depends on the attachment)
Pos. 2: The attachment operates in the reverse direction.
3. Lever C (Pictures 1+2)
Activation of hydraulic connectors C1 and C2 for rear-mounted
attachments:
Pos. 1: Raises/tilts the attachment (depends on the
attachment)
Pos. 0: Neutral (depends on the attachment)
4. Lever D (Picture 3)
Starts up attachments (depending on hydraulic connectors D1
and D2):
Pos. 1: Attachment operating
Pos. 0: Neutral – attachment stopped
Pos. 2: Attachment operating in the reverse direction
(depends on the attachment)
Quick action coupling D3:
Drain connection for various attachments (female – 1/4”)
5. Speed regulation of attachments (dened by the
attachment)
Regulates the oil ow in hydraulic connectors D1 and D2.
Warning!
Keep the quick action couplings clean of dirt
!
Levers A, B, C Hydraulic connectors B1, B2
Hydraulic connectors C1, C2
Hydraulic connectors D1, D2, D3 Lever D Speed regulation

13
1
2
3
4
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
General information
1.5 Operating levers and pedals - continued
Operation of attachments when the operator is not
sitting in the driver’s seat (exclusively for external
vacuum hose):
A) Park the basic machine and lock the parking brake
B) Keep the start button for attachment operation (Picture
1) depressed while operating lever D.
6. Parking brake (Picture 2)
Activation of parking brake: press the brake pedal to
its lowest position. The parking brake can then be slid
forward. Release the brake pedal, and the utility machine
is locked.
7. Brake pedal (Picture 2)
Activated in its lowest position.
8. Drive pedal (Picture 3)
The drive pedal can only be activated when the brake
pedal is in its highest position. The speed regulation is
stepless.
Drive forward: Press the pedal forward
Reverse: Press the pedal backward
The pedal returns to its neutral position automatically.
To drive at full speed, push the throttle all the way
forward.
9. Transport lock (Pictures 3+4)
The transport lock must be deactivated when the utility
machine is operating.
The transport lock must always be activated when the
utility machine is being driven from one location to
another.
The transport lock locks the A-frame in place so that the
A-frame cannot be lowered during driving. It also locks the
drive pedal so that the utility machine cannot reverse.
Lever D Manual start button
Brake pedal Parking brake
Drive pedal Transport lock deactivated
Transport lock activated

14
1
2
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
Generel information
1.5 Operating levers and pedals - continued
-
10. Towing lever (Pictures 1+2)
The towing lever under the machine is for moving the
utility machine manually.
When the towing lever is in open position, the machine
can be towed without starting the engine. The towing
lever is in open position when the lever is horizontal.
Warning!
When the towing lever is in open position,
there is no powered steering!
The towing lever must be in closed position for the utility
machine to be able to operate when the engine is started.
The towing lever is in closed position when the lever is
vertical.
The towing lever is tted to the transmission pump and is
located under the rear chassis of the Park Ranger 2150.
Towing lever open
Towing lever closed
!

15
1
2
3
4
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
General information
1.6 Fitting a cab (optional)
1. Lower the cab onto the utility machine. Use a crane with
a lifting strap that passes through the cab frame.
(Picture 1)
2. Fasten the cab to the utility machine chassis using two
bolts at the front and two bolts at the back. (Picture 2)
3. Connect the cab to the electrical system of the utility
machine. Remove the black cover on the right-hand side
of the instrument panel, pull out the electric plug and
connect it to the socket in the cab. (Picture 3)
4. Connect the hoses for the heating unit.
Remove the oil cooler cover.
Connect the two hoses from the cabin to the two hose
ends behind the oil cooler cover. (Picture 4)
5. Fill coolant into the utility machine.
Open the heat regulation system in the cab. Start the
machine and let it run in neutral for 5 minutes. Stop the
machine. Rell coolant, see Section 3.7.

16
61 42 53
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
General information
1. Heat regulation in the cab
2. Light switch: Position 1. Parking lights
Position 2. Driving lights
3. Work light, rear
4. Rotary light
5. Windscreen wipers: Position 1. Wipe
Position 2. Wipe and wash
6. Cab heater: Position 1. Half power
Position 2. Full power
1.7 Operating panel, cab (optional)

17
1
2
3
4
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
General information
1.8 Removable load carrier (optional)
Removing the load carrier
A) Move the locking lever to “released” position. To do this,
pull the lever out rmly while turning it to the right.
B) Pull the load carrier towards the back.
Fitting the load carrier
A) Fit the load carrier from the rear of the Park Ranger
2150. Push it into place so that it is seated in the locking
brackets on the frame.
B) Pull the locking lever out and turn it to the left while
the load carrier is pushed into position.
C) Make sure that the locking lever is locked in position in
the locking eye. Pull the load carrier to make sure that it is
locked in position.
Load carrier Locking handle
Locking eye Locking bracket
Locking lever in “released” position
Locking lever in “locked” position

18
1
2
3
2
1
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
1.9 Driver’s seat
Adjust the seat to suit the driver.
Height: use lever 1 to adjust the height
Weight: use lever 2 to adjust for weight
Forward/back: use lever 3 to move the seat forward or
back
1.10 Oil cooler cover
Removal:
A) The oil cooler cover is removed downwards at an angle.
Fitting (Picture 2):
A) Insert the top edge of the oil cooler cover at an angle
under the rim of the opening in the Park Ranger 2150.
B) Push the oil cooler cover into position.
Adjustment levers for the driver’s seat
Fitting the oil cooler cover
General information

19
1
2
3
4
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
Fuses in the steering wheel panel
Main fuse – 60 Amp
Fuses in the cab
Generel information
Main switch ON/OFF
1.11 Fuses and main switch
Fuses in the steering wheel panel
1. 7.5 Amp Charging lamp
2. 15 Amp Fan for oil cooler, safety net, magnetic
valve for engine cut-o, seat switch and
parking lights
3. 15 Amp Warning lights, horn and tank gauge
4. 15 Amp Electrical socket (trailer)
Main fuse
To access the main fuse, open the engine cover. The fuse
(60 Amp) is located on the right-hand side, just behind the
hydraulic oil tank.
Fuses in the cab
1. 7.5 Amp Right parking light
2. 7.5 Amp Left parking light
3. 20 Amp Cab heater
4. 20 Amp Rotary light, wiper motor and washer
pump
5. 20 Amp Driving lights and rear work light
Main switch
For it to be possible to start the Park Ranger 2150, the
main switch on the left-hand side of the machine must
be ON.
The main switch controls all power to the machine.

20
1
1
2
3
Operator’s Manual City Ranger 2150Operator’s Manual City Ranger 2150
Operator’s manual
2.1 Daily checks before start-up
Before carrying out the daily checks, open the engine
cover:
A) Remove the removable load carrier. See Section 1.8
B) Remove the radiator cover. See Section 3.1
C) Open the engine cover lock by pushing the locking
button 1) down and then opening the catch 2).
D) Open the motor cover.
It is important to check the following before
starting the machine:
Hydraulic oil:
Must be visible in the glass.
Filling – see “Maintenance”, Section 3.4.
Motor oil:
The oil level must be between the two lines on the
dipstick. Filling – see Section 3.5.
Cover lock Locking button Catch
Hydraulic oil
Motor oil