Egholm VS200 User manual

OPERATOR’S MANUAL
Tipping Shovel
90101361-01 UK

Introduction
Dear Customer
Thank you for buying an Egholm product.
The Egholm 2100 is a Danish designed and manufactured product which offers a very flexible way
of maintaining outdoor areas.
Get the optimal use of your Egholm Tipping Shovel:
To ensure the optimal performance of your Egholm Tipping Shovel, please read this operator’s man-
ual carefully before starting to use the machine. Failure to do so can result in personal injury and
damage to the machine.
Safety:
The Tipping Shovel is equipped with various devices to ensure optimal operational safety both for the
user and the surroundings. We therefore ask you to pay particular attention to Section 1.1 Safety. The
machine must only be serviced by professionals.
The Tipping Shovel is intended for professional use only. On delivery, the user will receive thorough
training to become a competent operator. Do not lend the machine to anyone who has not been thor-
oughly trained and has not read this manual carefully.
The operator’s manual should be considered as a permanent part of the machine and so must
remain with it if the machine is sold.
Warnings:
Some items in this operator’s manual are marked with this warning symbol.
The warning indicates areas where extra care has to be taken to avoid personal
injury or damage to the machine and its accessories. The warning also shows
what you should pay special attention to.
Reservations:
As it is the Egholm policy to make continuous improvements, we reserve the right to alter the specifi-
cations and equipment at any time without notice. Egholm Maskiner A/S accepts no liability for errors
or shortcomings in the operator’s manual.
Contact us:
Should you have questions of any kind regarding your new Egholm product, do not hesitate to con-
tact Egholm Maskiner A/S.
Best regards
Egholm Maskiner A/S - Transportvej 27 - DK - 7620 Lemvig
Tel: [phone] - Fax: [phone]
e-mail: [email protected] - www.egholm.dk
22

Contents
1. General information page
1.1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.2 EC Declaration of Conformity for Machinery . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.3 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2. Instructions for use
2.1 Assembly / Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.2 Before start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.3 Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3. Service and maintenance
3.1 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
3.2 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4. Conditions
4.1 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
4.2 Complaints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.3 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
33
1. General information
The Tipping Shovel makes light work of trans-
porting gravel, sand or mould and saves the
operator many lifts during the working day. 100
kg is easily transported from one place to anoth-
er - even on the narrowest paths.
The hydraulic tipping function is easy to work
with and perfect when, for example, the load
has to be tipped over an obstacle such as
sandpit edges or low hedges.
And now the load can be spread even while tip-
ping. The layer is levelled with the shovel edge,
giving a finished result.
The Tipping Shovel is a robust steel construction
which can perform many tasks other than shov-
elling, such as scraping grass edges of paths
with firm surfaces.

1. General information
1.1 Safety
Make sure no one is standing
close to the machine while it
is in use:
MMaakkeessuurreetthhaattnnoooonneeiissnneeaarrtthheemmaacchhiinnee
wwhhiilleeiittiissiinnuusseeaasstthheerreeiissaaddaannggeerrooff
ccrruusshhiinngg..
N.B!
AAssiittiissaarrttiiccuullaatteedd,,tthheerreeaarreennddoofftthhee
mmaacchhiinneesswwiinnggssoouuttwwhheennttuurrnniinngg..
MMaakkeessuurreetthhaattnnoooonneeiissssttaannddiinnggnneeaarrtthhee
mmaacchhiinneewwhhiilleeiittiissiinnuussee..((PPiiccttuurree11))
Avoid crushing fingers
KKeeeeppyyoouurrhhaannddssaannddffiinnggeerrssaawwaayyffrroomm
aarreeaasswwhheerreetthheerreeiissaaddaannggeerrooffccrruusshhiinngg..
KKeeeeppyyoouurrhhaannddssaanndd
ffiinnggeerrssaawwaayyffrroommtthhee
TTiippppiinnggSShhoovveellwwhheenniittiissiinnuusseeaasstthheerreeiiss
aaddaannggeerrooffccrruusshhiinngg..((PPiiccttuurree22))
Avoid roll-overs:
DDoonnoottddrriivveetthheemmaacchhiinneeiinnaappllaacceewwhheerree
iittccaannsslliiddee,,ttiippoorrrroollll..DDoonnoottddrriivveeoonn
ssllooppeesswwiitthhaanniinncclliinneeooffmmoorreetthhaann1100°°..
((PPiiccttuurree33))
Reduction of noise and energy
consumption:
IIttiissrreeccoommmmeennddeeddnnoottttooddrriivveewwiitthhaahhiigghheerr
eennggiinneessppeeeeddtthhaannnneecceessssaarryy,,ttoorreedduucceetthhee
nnooiisseeaannddtthheeeenneerrggyyccoonnssuummppttiioonn..
44
Prevent people from standing
in the working area.
Warning!
Do not drive on slopes with
an incline of more than 10°
11
11
22
22
33
33
Max. 10°

1. General information
1.2 EC Declaration of Conformity for Machinery
Manufacturer: Egholm Maskiner A/S
Address: Transportvej 27, DK-7620 Lemvig
Telephone: [phone]
hereby declares that
-Machine: Tipping Shovel Type: VS200
Serial no.: ____________________________ Year: _________________
- has been manufactured in conformity with the provisions of the Machinery
Directive, Directive 98/37/EU
55
The Egholm 2100 fitted with the cab FH 2100 (ROPS approved)
- has been tested at the Danish Institute of Agricultural Sciences at Bygholm in
conformity with directive 86/298/EEC concerning rear mounted, roll-over pro-
tection structures of narrow-track wheeled agricultural and forestry tractors.
Place: Lemvig
Date: ______________
Signature: ______________
Kaj Egholm, MD

1. General information
66
Side view
Front view
Location of model plate
11
11
22
22
33
33
1.3 Technical data
Dimensions: Assembled: Storage dimensions:
Length (L): 2,790 mm 670 mm
Width (W): 1,020 mm 1,020 mm
Height without cab (H): 330 mm 330 mm
Height with cab: 1,935 mm
Technical data:
Type description: VS200
Own weight: 38 kg
Capacity of the Tipping Shovel: 65 litres
Lifting capacity: 100 kg
Ground clearance under shovel, raised: 480 mm
N.B!
Specifications may be changed without prior notice.
LL
LL
HH
HH
WW
WW

2. Instructions for use
2.1 Assembly / Disassembly
1. It is recommended that the hydraulic hoses should
be run over the edge of the shovel blade to keep
them clear and free from dirt when the Tipping
Shovel is fitted. (Picture 1)
2. The locking handle on the A-frame of the machine
must be in the open position. (Picture 2)
3. Drive the machine right up to the A-frame of the
Tipping Shovel, so the A-frames fit into each other.
(Picture 2)
4. Raise the A-frame with lever A on the left-hand side
of the machine until the Tipping Shovel is freely sus-
pended above the ground. (Picture 3)
5. Lock the Tipping Shovel in place with the locking
handle on the A-frame. (Picture 2)
6. Stop the machine. (See the operator’s manual for
the basic machine, section 2.2)
7. Fit the hydraulic hoses on the B-connectors on
the left-hand side of the machine. (Picture 3)
8. Attach the hydraulic hoses with the rubber strap
under the running board to ensure it runs correctly
over the screen. (Picture 4)
Disassembly:
Follow the procedure for fitting in reverse order.
Put the protective caps on the snap couplings to
protect them from dirt.
77
Hydraulic hoses
Locking handle on the A-frame - open
Lever A B-connectors
The hoses are fastened
with a rubber strap
11
11
22
22
33
33
44
44
LL
LLee eeff fftt tt-- --hh hhaa aann nndd dd ss ssii iidd ddee ee
AA
AABB BBCC CC
LL
LL
oo
oo
cc
cc
kk
kk
ee
ee
dd
dd
BB
BB11 11BB
BB22 22

2. Instructions for use
2.2 Before start-up
During transport, lock the Tipping Shovel in the
raised position with the transport lock. (Picture 1)
2.3 Start-up
Raising and lowering the Tipping Shovel:
- Raise the Tipping Shovel by pushing lever A on the
left-hand side of the machine up to position 1.
(Picture 2)
- Lower the Tipping Shovel by pushing lever A on the
left-hand side of the machine down to position 2.
(Picture 2)
Tipping the shovel blade:
- Tip the shovel blade upwards by pushing lever B on
the left-hand side of the machine up to position 1.
(Picture 2)
-Tip the shovel blade downwards by pushing lever B
on the left-hand side of the machine down to posi-
tion 2. (Picture 2)
Warning!
MMaakkeessuurreetthheerreeiissnnoooonneecclloosseettootthhee
mmaacchhiinneewwhheenniittiissrruunnnniinngg..
N.B!
WWhheennttuurrnniinngg,,tthheerreeaarroofftthheemmaacchhiinnee
sswwiinnggssoouutt,,ssootthheerreeiissaarriisskkooffccrruusshhiinnggoorr
ccoolllliissiioonn..
IIttiiss
rreeccoommmmeennddeeddnnoottttooddrriivveewwiitthhaahhiigghheerr
eennggiinneessppeeeeddtthhaannnneecceessssaarryy,,ttoorreedduuccee
tthheennooiisseeaannddtthheeeenneerrggyyccoonnssuummppttiioonn..
88
Transport lock
Lever A Lever B
Shovel lowered
Shovel raised and tipped
11
11
22
22
33
33
44
44
LL
LL
oo
oo
cc
cc
kk
kk
ee
ee
dd
dd
LL
LLee eeff fftt tt-- --hh hhaa aann nndd dd ss ssii iidd ddee ee
AA
AABB BBCC CC

3. Service and maintenance
3.1 Cleaning
Daily cleaning and maintenance will extend the lifetime
of both the machine and the attachment.
Clean the Tipping Shovel with clean water after use.
3.2 Maintenance
It is recommended that you regularly remove any loose
paint and repaint any damaged areas.
99

4. Conditions
1100
4.1 Warranty
The warranty period for the materials and manu-
facture of the Tipping Shovel is 12 months from
the date of purchase.
In case of errors or defects on the machine with-
in the warranty period, Egholm Maskiner A/S will
carry out the necessary repairs without charge
for materials and working hours in accordance
with the terms and conditions listed below. The
customer is to cover the costs for transportation
for repair.
The scope of warranty:
1) The Egholm warranty is only valid on presen-
tation of the original receipt supplied with
model description, serial number and date of
purchase.
2) Regular checks, adjustments, services and
technical alterations are not covered by
the guarantee.
3) All inquiries concerning the warranty are to
be addressed to the place where the
machine was purchased.
4) This warranty does not cover faults and
defects which cannot be traced back to
defects in material or production errors.
5) Egholm Maskiner A/S reserves the right to
make improvements and design-related
alterations to the machine without being
obliged to modify previously delivered mod-
els in relation hereto.
6) This warranty is valid for persons who have
legally acquired the machine within the war-
ranty period.
The guarantee does not cover:
*Wear and tear, accidents, damage to the
equipment caused by operating errors,
changes to the construction of the machine, or
use of non-Egholm spare parts or implements.
* Machines with illegible serial numbers.
* Damage caused by force majeure such as
lightning, flood, fire, war, civil disturbance
etc. or other causes over which Egholm
Maskiner A/S has no control.

4. Conditions
4.2 Complaints
All inquiries regarding the machine should be made to the distributor from whom the machine was
purchased. This applies to inquiries concerning normal use, service, maintenance and spare parts as
well as to any complaints.
If there are questions that the distributor cannot answer, please do not hesitate to contact Egholm
Maskiner A/S directly. Also feel free to contact us with suggestions or requests for special implements
and/or features for the machine. We wish you many years of safe and satisfied use of your machine.
Best regards
Egholm Maskiner A/S - Transportvej 27 - DK -7620 Lemvig, telephone: [phone], fax: [phone]
4.3 Disposal
When - many years from now - your Tipping Shovel comes to the end of its working life,
it should be disposed of in a responsible manner and conform with the relevant disposal regulations.
1. Used hydraulic oil is to be disposed of at an approved waste disposal facility or site.
2. Remove all plastic and rubber parts and discard in a dustbin.
3. After the parts mentioned have been removed the tool is ready to be handed over to one of your
local approved scrap merchants.
1111

Egholm Maskiner A/S * Transportvej 27 * DK-7620 Lemvig Tel.:
Tel: [phone] - Fax: [phone]
www.egholm.dk * [email protected]