ekwb EK-Quantum Surface P360M User manual

USER GUIDE
RADIATOR
EK-Quantum
Surface Radiator Setup Configurations

Please note the installation of the product is intended to be undertaken
by an adequately trained and experienced person. You are installing the
product at your own risk. If you are not properly trained or experienced
or feel unsure about the installation procedure, please refrain from
installing the product yourself and contact our tech support for
assistance. We disclaim our liability for any damages to the product as
well as incidental, consequential, or indirect damages incurred due to
improper or inappropriate installation.
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.

- 3 -
TABLE OF CONTENTS
EK-QUANTUM SURFACE RADIATORS 4
EXPLODED VIEW OF THE REMOVABLE COMPONENTS FOR S, P AND X SERIES 6
EKQUANTUM SURFACE S SERIES 6
EKQUANTUM SURFACE P SERIES 7
EKQUANTUM SURFACE X SERIES 8
SUPPORT AND SERVICE 9
SOCIAL MEDIA 9

- 4 -
EK-QUANTUM SURFACE RADIATORS
EK-Quantum Surface Radiators have a classical U-shape coolant
flow, with inlet and outlet both on one side of the radiator. However,
you can still choose which port of the radiator will serve as an inlet,
and which for the outlet in your custom loop.
SETUP 1
Picture on the left shows the first flow direction setup of the EK-
Quantum Surface P360M Radiator which is a Multiport radiator. On
the non-multiport radiator you can choose only one inlet and one
outlet port.
SETUP 1
OUTLET
OPTIONS
INLET OPTIONS
EK-Quantum Surface P360M
SETUP 2
Picture on the left shows the second flow direction setup of the EK-
Quantum Surface P360M Radiator which is a Multiport Radiator. On
the non-multiport radiator you can choose only one inlet and one
outlet port.
SETUP 2
INLET
OPTIONS
OUTLET OPTIONS
EK-Quantum Surface P360M

- 5 -
On the Multiport Radiator, opposing to the inlet/outlet side of the radiator,
there is an extra port for filling or draining the loop.
It should not be used as an inlet or an outlet port!
EK recommends using the same number of inlets and
outlets for the most optimal performance!
It is mandatory to use the extenders on any inlet and
outlet position!
If transferred from the stock position of the radiator
to another, check if the extenders are tightened to
avoid leakage!
The same port setup applies for all EK-Quantum Surface
radiator variants!
FILL/DRAIN
PORT

- 6 -
EXPLODED VIEW OF THE REMOVABLE COMPONENTS FOR S, P AND X SERIES
For reference on picture above: EK-Quantum Surface S240
EKQUANTUM SURFACE S SERIES
2x QUANTUM
SURFACE
EXTENDER
2x QUANTUM SURFACE END TANK SHROUD
(ALUMINIUM) 2x QUANTUM SURFACE
SIDE PLATE
(STAINLES STEEL)
8x TORX SCREW M3 x 6 mm
QUANTUM SURFACE TANK

- 7 -
For reference on picture above: EK-Quantum Surface P360M
EKQUANTUM SURFACE P SERIES
2x QUANTUM
SURFACE
EXTENDER
2x QUANTUM SURFACE END TANK SHROUD
(ALUMINIUM)
2x QUANTUM SURFACE
SIDE PLATE
(STAINLES STEEL)
8x TORX SCREW M3 x 6 mm
QUANTUM SURFACE TANK
3x QUANTUM SURFACE PLUG
(MULTIPORT VERSION)

- 8 -
For reference on picture above: EK-Quantum Surface X420M
EKQUANTUM SURFACE X SERIES
2x QUANTUM
SURFACE
EXTENDER
2x QUANTUM SURFACE END TANK SHROUD
(ALUMINIUM)
2x QUANTUM SURFACE
SIDE PLATE
(STAINLES STEEL)
8x TORX SCREW M3 x 6 mm
QUANTUM SURFACE TANK
3x QUANTUM SURFACE PLUG
(MULTIPORT VERSION)

In case you need assistance, please contact:
https://www.ekwb.com/customer-support/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA