ekwb EK-Quantum Reflection Uni 140 D5 PWM D-RGB User manual

USER GUIDE
EKQuantum
Reflection Uni 140 D5 PWM D-RGB

Before you start using this product please follow these basic guidelines:
Please carefully read the manual before beginning with the
installation process!
The EK fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber o-ring gaskets.
The use of corrosion inhibiting coolants is always recommended
for any liquid cooling system. EKWB recommends any of the
EK-Cryofuel for worry-free usage.
There are many ways to install and configure the Reflection UNI 140, it
can be mounted to any 140mm fan position with standard 125x125mm
hole spacing the same as all EK 140mm fans and radiators. The threads
in this product are M4 with a maximum penetration of 8mm, use of
longer or improper screws may permanently damage the product!

- 3 -
TABLE OF CONTENT
BOX CONTENTS 4
MOUNTING INFORMATION 5
INSTALLING EK-QUANTUM REFLECTION UNI 140 D5 PWM D-RGB 6
RECOMMENDED CONFIGURATIONS 7
CONNECTING THE D-RGB LED STRIP 10
CONNECTING THE PUMP 10
TESTING THE LOOP 11
SUPPORT AND SERVICE 12
SOCIAL MEDIA 12

- 4 -
BOX CONTENTS
EK-Quantum Reflection Uni 140
D5 PWM D-RGB
M4 x 8 Screw DIN7984 (5 pcs) M4 PVC Washer (5 pcs)
Allen Key 2.5 mm (1 pc) EK-Loop Multi Allen Key
Bag content: Bag content is universal, you may not need all screws.
8 mm

- 5 -
MOUNTING INFORMATION
The Reflection UNI 140 can be mounted to any standard 140mm
mount (125x125mm) using the supplied M4 screws. However, it
must always be mounted vertically, to assist with filling and bleeding
it is optimal to keep the pump in the lowest possible position as
shown here:
Never mount or operate EK-Quantum Reflection UNI 140 D5
PWM D-RGB horizontally as this would allow air to accumulate in
the pump causing permanent damage to the bearing and motor.

- 6 -
INSTALLING EK-QUANTUM REFLECTION UNI 140 D5 PWM D-RGB
Using the included M4 screws you can mount the Reflection UNI 140
directly to your chassis or any other 140mm fan mounting location.
EK-Quantum
Reflection UNI 140
D5 PWM D-RGB
M4 X 8 DIN 7984
Lian Li DK-05F Desk
Lian Li DK-05F Desk

- 7 -
RECOMMENDED CONFIGURATIONS
The EK-Loop Multi Allen Key (6mm, 8mm, 9mm) may be used to
install all EK fittings, do not use excessive force. All unused ports
should be blocked using G1/4 plugs.
Using EK-Quantum Reflection UNI 140 D5 PWM D-RGB as a
PUMP/RES Combo:
When using the Reflection UNI 140 as a pump/res combo in any
orientation there is only one possible outlet port! Two of the ports
cannot be used and must be plugged as shown below!
INLET
NOT USABLE
INLET / DRAIN
FILL
OUTLET
FILL
NOT USABLE
INLET
NOT USABLE
INLET / DRAIN
FILL
OUTLET
FILL
NOT USABLE

- 8 -
Using EK-Quantum Reflection UNI 140 D5 PWM D-RGB as a
distribution plate:
If components will only be connected to 2 of the ports, please
observe pump/res combo configurations!
There are 2 sets of Inlet and Outlet ports (A and B) that are linked
in series, each pair may be used to connect one or multiple
components in series or parallel as required. Components in Set A
must return to Inlet A where the coolant passes directly to Outlet B.
The components in Set B may return to any Inlet B position.
INLET B
OUTLET B
INLET B/DRAIN
FILL
OUTLET A
FILL
INLET A
INLET B
INLET A
INLET B / DRAIN
FILL
OUTLET A
FILL
OUTLET B

- 9 -
INLET B
INLET A
INLET B/DRAIN
FILL
OUTLET A
FILL
OUTLET B
INLET B
OUTLET B
INLET B / DRAIN
FILL
OUTLET A
FILL
INLET A

- 10 -
CONNECTING THE D-RGB LED STRIP
Plug the 3-pin connector of the distribution plate D-RGB LED light
to the D-RGB HEADER on the motherboard. The LED will work if the
pin layout on the header is as follows: +5V, Digital, Empty, Ground.
D-RGB Header
RGB Header
CONNECTING THE PUMP
The EK-D5 PWM pump has two connectors.
1. 4-pin Molex: It must be connected directly to your PSU at all
times as it is used to power the pump.
2. 4-pin PWM fan: It can be connected to your motherboard’s
CPU_ Fan or designated water pump header. It can also be
connected to a controller. This cable is used to control and report
the rotational speed of the pump. If it’s not connected, the pump
will run at maximum speed (100% PWM).
4-pin molex
connector
4-pin PWM fan
connector