ekwb EK-XRES Revo D5 User manual

EK-XRES Revo D5
2nd revision, Oct 25th 2016
USER GUIDE

/ 2 /
INSTALLING THE XRES D5 (already done by EK)
61x3mm sealing gasket (OR)
D5 pump body
with motor
Screws M3x12
NU T M74
Pump
holder
Rubber damper
EK-XRES D5

/ 3 /
STEP 1
Install the EK-XRES Revo D5 onto the pump main motor
housing. Make sure you install EK provided 61x3mm o-ring
gasket! Reseat the gasket if needed. You can rotate the
pump and use it in any direction except upside-down to best
suit your installation.
STEP 2
Secure the pump on the EK-XRES Revo D5 using en-
closed M74 Nut.

/ 4 /
ADDITIONAL DAMPER
Top pyramids must be facing UP

/ 5 /
Additional Revo D5 Damper is enclosed. If pump vibrations
are higher than expected additional Revo D5 Soft dump-
er can be used. When replacing damper, take care that top
pyramids are faced up as shown on picture below. In case of
severe tilting of the computer chassis reservoir unit may fall
out of the holder. Additional damper use is recommended in
vertical reservoir unit mount

/ 6 /
USING POLYETHER ANTI-VORTEX FOAM or EK-HD Tube
EK-XRES Revo D5 series pump top / reservoir comes pre-
installed with Anticyclone by default. In case your system
suffers from excessive vortex issues, air bleeding problems
or if the pump is sucking in air you may replace the anticy-
clone with the enclosed polyether foam or EK-HD Tube.
There are two ways to use the polyether anti-vortex foam:
Default configuration PE foam – use whole
This is the default configuration
of EK-XRES Revo D5 series
reservoir.
Use the foam as a whole to re-
place the Anticyclone.

/ 7 /
PE foam – trim to fit recess HD Tub e
Trim the foam to size to fit into
the desired inlet recess on the
EK-XRES Revo D5 main body.
Insert enclosed o-ring 16x2 into
the groove inside center hole
and insert enclosed EK-HD
Tub e 12/ 16 .

/ 8 /
INSTALLING THE RESERVOIR
By default the EK-XRES Revo D5 ships with EK-Revo D5
Holder. This holder is meant to be installed directly on the
computer chassis. User may need to drill 4 (four) Φ5mm
(enclosed sticker with designated holes) holes through the
metal chassis using electric power drill if there are no appro-
priate mounting holes available.
Computer chasis
metal plate
Washer
M4x10 screw
OUTLET
INLET
EK-Revo D5 Holder

/ 9 /
EK recommends users to find an appropriate position in your
computer chassis to install the EK-XRES Revo D5 pump as-
sembly. To successfully install the EK-XRES Revo D5 pump/
reservoir assembly please complete the following steps:
1. Find an appropriate position for the unit inside (or perhaps
outside) of your computer chassis; drill mounting holes if
needed. Sticker with designated holes position is enclosed.
Before drilling stick it to the Computer chassis.
2. Attach the EK-Revo D5 Holder to the computer chas-
sis metal frame using enclosed 4 (four) M4x10 DIN7984
screws and PVC washers. Secure the screws using en-
closed Allen key 2.5mm.
3. Insert the rubber damper into the EK-Revo D5 Holder.
Insert the pump into the damper. And secure it using two
M3x12 DIN7984 screws from the side of the holder. Use
enclosed 2mm Allen key. Your installation is now complete.

/ 10 /
AT TACHING FIT TINGS
EK-XRES Revo D5 PWM (incl. pump) series reservoir
pump combo featured 3 (three) G1/4 threaded ports on the
main body of which 1 (one) is inlet and other is outlet. When
reservoir is in upright position outlet port is positioned lower
than inlet port. EKWB recommends using EK-ACF fittings
with the EK-XRES Revo D5 PWM series reservoir pump
combo units. To ensure that the tubes are securely attached
to the barb/fittings, please use hose clamps or an appropri-
ate substitute.
OUTLET INLET
EK-Plug G1/4
EK-ACF Fitting