ekwb EK-Quantum Reflection PC-O11D XL D5 PWM... User manual

USER GUIDE
DISTRIBUTION PLATE
EKQuantum
Reflection PC-O11D XL D5 PWM D-RGB

Before you start using this product please follow these basic guidelines:
Please carefully read the manual before beginning with the
installation process!
The EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber O-ring gaskets.
The use of corrosion inhibiting coolants is always recommended
for any liquid cooling system. EKWB recommends any of the
EKCryofuel for worry-free usage.

- 3 -
TABLE OF CONTENT
BOX CONTENTS 4
PREPARING THE 011D XL CHASSIS 5
INSTALLING THE DISTRIBUTION PLATE IN THE 011D XL 7
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS 9
CONNECTING THE D-RGB LED STRIP 11
CONNECTING THE PUMP 11
TESTING THE LOOP 12
SUPPORT AND SERVICE 13
SOCIAL MEDIA 13

- 4 -
BOX CONTENTS
EK-Quantum Reflection PC-O11D XL
D5 PWM D-RGB
Front mounting Bracket (1 pc) M3x6 DIN7380 (2 pcs)
M3x8 DIN7991 (5 pcs) M3 Nut (2 pcs)
Allen Key 2mm (1 pc) EK-Loop Multi Allen Key

- 5 -
PREPARING THE 011D XL CHASSIS
Before installing the distribution plate, carefully read
the PC case manual.
STEP 1
Unscrew the factory provided screws and remove the top panel
from the case.
STEP 2
STEP 2
Remove both side panels and the front panel from the case.
STEP 1

- 6 -
STEP 3
STEP 3
The SSD Trays also need to be removed from the back side of
the chassis. Once the distribution plate is secured they can be
reinstalled as required.
STEP 4
For easier installation of the distribution plate, you should remove
the Fan/SSD Tray from the bottom of the case.
Unscrew the 2(two) marked factory screws and remove the Fan/
SSD Tray. After securing the distribution plate, it can be reinstalled
with the bottom radiator and fans.
STEP 4
Factory Screws

- 7 -
INSTALLING THE DISTRIBUTION PLATE IN THE 011D XL
STEP 1
Carefully place the EK-Quantum Reflection PC-O11D XL D5 PWM
D-RGB distribution plate into the PC case and align the mounting
holes at the back.
STEP 1
STEP 2
Secure the distribution plate to the chassis with two (2) M3 x 6
DIN7380 and M3 nuts (as shown in the diagram).
M3 Nut
STEP 2
DETAIL
VIEW
Mounting
Bracket
M3 x 6 DIN7380

- 8 -
STEP 3
STEP 3
Position the front mounting bracket onto the distribution plate and
secure it with five(5) M3 X 8 DIN7991 mounting screws.
DETAIL VIEW
M3 X 8 DIN7991
Front mounting
Bracket
M3 X 8 DIN7991
Front mounting Bracket

- 9 -
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS
It is mandatory to use at least one of each type of port and all
remaining ports should be sealed using the supplied plugs. The
EK-Loop Multi Allen Key (6mm, 8mm, 9mm) may be used to install
all EK fittings, do not use excessive force.
If one of the prescribed components will not be installed (ie. bottom
radiator or GPU block) then one IN and one OUT port must still be
joined together in order for this distribution plate to function!
TOP
RADIATOR
OUTLET
FILL
GPU INLET GPU OUTLET
DRAIN
TOP RADIATOR
INLET
CPU INLET
CPU OUTLET
BOTTOM
RADIATOR
OUTLET
BOTTOM
RADIATOR
INLET

- 10 -
FILL (exterior)
DRAIN (exterior)