ekwb EK-FC460 GS/SONIC Manual

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 17th of November, 2010.
Installation and mounting manual for EK-FC460 GS/SONIC water block
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.
Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the
liquid seal is made using o-rings.
STEP 1: GENERAL INFORMATION. Sample picture of Palit GeForce GTX 460 Sonic Platinum 1GB
STEP 2: PREPARING YOUR GRAPHIC CARD.
1. REMOVING STOCK COOLER: Remove encircled screws on the
bracket:
STEP 2: PREPARING YOUR GRAPHIC CARD
1. REMOVING STOCK COOLER. Remove all encircled screws. All heat sink assembly
screws and retention plate should be removed. Also remove screws on side plate. There
are 9 screws on the back of the graphic card.
2. CLEANING THE PCB. Carefully detach the original heat sink after removing all
fasteners securing it to the board and bracket. Wipe off the remains (by using non–
abrasive cloth or Q-tip, as shown on sample photo) of the original thermal
compound until the components and circuit board are completely clean. EKWB does
not recommend using any liquids for removing paste.
3. APPLYING THERMAL COMPOUND
Apply thermal compound: lightly coat the GPU with for example Arctic Cooling MX2 ™ or
MX3 ™ thermal compound. Follow this link:
http://www.arctic-cooling.com/catalog/images/install_mx2_retail.pdf for detailed
instructions. EKWB recommends to apply thermal grease in cross form for best
performance (see sample picture).
4. CUTTING THERMAL PADS. Your block comes with thermal pads, which have to be
placed on chips (PLEASE REMOVE FOIL ON BOTH SIDES OF THERMAL PADS PRIOR
TO INSTALLATION. WARNING: DIMENSION BELLOW ARE SCALED.) All thermal pads
are 1mm thick.
STEP 3: INSTALLING WATER BLOCK
1. PLACING THERMAL PADS ON PCB. Place thermal pads on chips so that numbers on
chips match size of thermal pads. Thermal pads have to be cut by user to match all small
chips (EKWB made sure users have more than enough pads to cover all surfaces that
need to be covered to make block fully function). You can also use small drop of thermal
grease on chips to make thermal pads more adhesive.
2. PLACING STANDOFFS ON BLOCK. Please use small amount of thermal grease on
standoffs and glue them so they are concentric with mounting holes. Once they are
stuck to block be careful not to move them.

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 17th of November, 2010.
2.cont.. PLACING STANDOFFS ON BLOCK. Standoffs (thickness 2,5mm) are obligatory for
safe mounting and also to make this block fully functional.
3. ATTACHING BLOCK TO GRAPHIC CARD. By using Philips screwdriver, screw in
enclosed M3x8 and M3x6 screws . EKWB recommends start screwing the screws
around the GPU core and continue outwards. (HINT: leave screws half screwed in
until all are in their places, then fasten them. However, do not overdo it, as you may
strip threads.)
STEP 4: CHECKING FOR CONTACTS
Temporarily r emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat
substeps in previous section to reattach the block. In case you can’t get good contact, please check again your thermal pad thickness our contact our support service.
STEP 5: POSITIONING FITTINGS
Please use spacer only on copper base if you use fitting with G1/4 thread longer than 5mm (see sample picture). Screw in the fittings and plugs (please use spacers only on
copper base for fittings). Use 6mm Allen key to screw in and tighten new EK-Plug G1/4. Attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit.
EKWB recommends using high flow fittings with the EK-FC 4X0 GTX series water blocks. To ensure that the tubes are securely attached to the barb/fittings, please use hose
clamps or an appropriate substitute. The use of an algaecide is always recommended for any liquid cooling system.
You can use any hole as an inlet/outlet hole.
STEP 6: INSERTING CARD IN YOUR PC CASE
Carefully lift your card with installed block and insert it in your PC case. Please bear in mind that your card suddenly withstands extra weight thus again be very careful not to
bend it or cause any other unneeded moves that might damage your card or block during installation.
STEP 6: IMPORTANT NOTICE
You will void the warranty by disassembling the water block. Due to the specific design we cannot guarantee leak proof seal after the water block has been opened by a
third-party.
REQUIRED TOOLS AND MOUNTING SCREWS:
scissors philips screwdriver 6 x screws M3x8 DIN7985 3 x screws M3x8 DIN7985 9x PVC washer
Fitting
Gasket/O-ring
G1/4
Spacer
Plug
M3x6 screws and enclosed
washers must be used on
this place.
Plug
6mm Allen key