ELAN Lighting CABLED-150-SPOT-MKII User manual

CABLED-150-SPOT-MKII
Thank you for purchasing a product from our CABLED-150-SPOT-MKII. Every suit has been
thoroughly tested and shipped in perfect condition. Carefully check the shipping carton for
damage that may have occurred during shipping. If the carton appears to be damaged,
carefully inspect your unit for any damage and be sure all accessories necessary to operate
the unit has arrived intactly. In the case damage has been found or parts are missing, please
contact Acson Comercial or your local supplier for further instructions. Do not return this unit
without any warning.
USER’S MANUAL

2
Contents
FOR YOUR OWN SAFETY, PLEASE READ
THIS USER MANUAL CAREFULLY BEFORE
POWERING OR INSTALLING. SAVE IT FOR
FUTURE REFERENCE
1. Safety Instructions ............................................................................................ 3
2. Unpacking ......................................................................................................... 4
3. Features & Specifications ................................................................................. 4
4. Photometric Data ............................................................................................... 5
5. Operation Instructions ...................................................................................... 6
6. Installation Instructions .................................................................................... 6
7. DMX-512 Control Connections.......................................................................... 8
8. Menu Operations ............................................................................................... 8
9. Cleaning and Maintenance ............................................................................... 10

3
1. Safety Instructions
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe
operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written
in this user manual.
• If the device has been exposed to temperature changes due to environmental changes, do not switch it
on immediately. The arising condensation could damage the device.
• Leave the device switched off until it has reached room temperature.
• This device falls under protection-class I. Therefore it is essential that the device be earthed.
• The electric connection must carry out by qualified person.
• The device shall only be used with rate voltage and frequency.
• Make sure that the available voltage is not higher than stated at the end of this manual.
• Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, re-
placement of the cable must be done by an authorized dealer.
• Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power cord by the plug. Never pull out the plug by tugging the power cord.
• During initial start-up some smoke or smell or smell may arise. This is a normal process and does not
necessarily mean that the device is defective, it should decrease gradually.
• Please don’t project the beam onto combustible substances.
• Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for
smooth air flow, so there should be no shelter for fans and ventilation for heat radiation.
• If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the
manufacturer of his service agent or a similar qualified person in order to avoid a hazard.
Caution!
Be careful when operating this fixture. High voltage can cause dangerous
electric shock when manipulating wires.
!
Please review the following before you start

4
2. Unpacking
3. Features & Specifications
Thank you for choosing our CABLED-150-SPOT-MKII moving head light. For your own safety, please read
this manual before installing the device. This manual covers the important information on installation and
applications. Please install and operate the fixture according to these instructions. Please keep this manual
well stored for future needs.
The CABLED-150-SPOT-MKII is made of a new type of high temperature strength of engineering plastic
and cast aluminum casing with nice outlook. The fixture is designed and manufactured strictly following CE
standards, complying with international standard DMX512 protocol. It’s available independently controlled
and linkable with each other for operation. And it is applicable for large-scale live performances, theater,
studio, nightclubs and discos.
The CABLED-150-SPOT-MKII features high brightness and stability. Please carefully unpack it when you
receive the fixture and check whether it is damaged during the transportation.
• 150W High Output White LED
• 50,000 hours lifespan and low power con-
sumption
• Beam Angle 15°, focus function
• High light output, 3450LUX@5M at White light
• Temperature protect function, when the in-
ternal Temperature is up to 40° and then the
fans begin to work, when the internal tempe-
rature is up to 70°and the brightness reduce
half.
• Color Wheel: 7 colors +white, rotation with
variable direction and speed
• 1 static Gobo Wheel: 8 gobos +white, wheel
rotation and shake
• 1 Rotation Gobo Wheel: 6 gobos +white, whe-
el rotation and shake
• Prism: 3-facet Prism, bi-directionally rotatable
at variable speeds
• High speed strobe effect with 1-25 flashers
per second
• Internal program available
• 16/14/12/10 DMX Channels USITT DMX-512
• DMX 512, master-slave and sound activated
controllable or auto operation
• Colorful LCD display
• Efficient low noise fan cooling system
• POWERCON IN/OUT
• 3-pin XLR connectors IN/OUT
• Two 1/4 turn fastening Omega Clamps
• IP 20 protection rating
1
1
2
3
4
5
2
3
45
Make sure the following items are included inside the box:
Moving head (1pc)
Signal Cable (1pc)
Omega Clamp (1pc)
Power Cable (1pc)
User Manual (1pc)

5
4. Photometric Data
Specifications
Dimensions
• Input Voltage: AC90-260V 50/60Hz
• Light Source: 150W High Output White LED
• Control Signal: DMX 512, master-slave and
sound activated or auto operation
• Control Channel: 16/14/12/10 DMX Channels
USITT DMX-512
• Power Consumption: 250W
• Dimensions: 270(D)*270(W)*470(H)mm
• Packing size: 305(D)*305(W)*500(H)mm
• Net Weight: 10.6kg,
• Gross Weight:12.6kg

6
5. Operation Instructions
6. Installation Instructions
• The moving head is for spot effect for on-site decoration purpose.
• Don’t turn on the fixture if it’s been through severe temperature difference like after transportation becau-
se it might damage the light due to the environment changes. So make sure to operate the fixture until it
is in normal temperature.
• This light should be keep away from strong shaking during any transportation or movement.
• Don’t pull up the light by only the head, or it might cause damages to the mechanical parts.
• Don’t expose the fixture in overheat, moisture or environment with too much dust when installing it. And
don’t lay any power cables on the floor. Or it might cause electronics shock to the people.
• Make sure the installation place is in good safety condition before installing the fixture.
• Make sure to put the safety chain and check whether the screws are screwed properly when installing
the fixture.
• Make sure the lens are in good condition. It’s recommended to replace the units if there are any dama-
ges or severe scratch.
• Make sure the fixture is operated by qualified personnel who know the fixture before using.
• Keep the original packages if any second shipments is needed.
• Don’t try to change the fixtures without any instruction by the manufacturer or the appointed repairing
agencies.
• It is not in warranty range if there are any malfunctions from not following the user manual to operate or
any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.
• Before mounting the fixture to any surface, make sure that the installation area can hold a minimum
point load of 10 items the device’s weight.
• Fixture installation must always be secured with a secondary safety attachment, such as an appropriate
safety cable.
• Never stand directly below the device when mounting, removing, or servicing the fixture.
• From a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept at least
0.5m (1.5ft) away from any flammable materials (decoration etc.).
• Always use and install the supplied safety cable as a safety measure to prevent accidental damage and/
or injury in the event the clamp fails.
Caution!
For added protection mount the fixtures in areas outside walking paths,
seating areas, or in areas were the fixture might be reached by unauthori-
zed personnel.
!

7
• Overhead mounting requires extensive experience, including amongst others calculating working load
limits, a fine knowledge of the installation material being used, and periodic safety inspection of all ins-
tallation material and the fixture. If you lack these qualifications, do not attempt the installation yourself.
Improper installation can result in bodily injury.
• Be sure to complete all rigging and installation procedures before connecting the main power cord to the
appropriate wall outlet.
• The LED moving head provides a unique mounting bracket assembly that integrates the bottom of the
base, and the safety cable rigging point in one unit (see the illustration below). When mounting this
fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a
M10 screw fitted through the center hole of the “omega bracket”. As an added safety measure be sure to
attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point
integrated in the base assembly.
• Regardless of the rigging option you choose for your LED moving head, always be sure to secure your
fixture with a safety cable. The fixture providers a built-in rigging point for a safety cable on the hanging
bracket as illustrated above. Be sure to only use the designated rigging point for the safety cable and
never secure a safety cable to a carrying handle.
Mounting points:
Clamp Mounting:

8
7. D MX-512 Control Connections
8. Menu Operations
1Connect the provided XLR cable to the fe-
male 3-pin XLR output of your controller and
the other side to the male 3-pin XLR input of
the moving head.You can chain multiple mo-
ving head together through serial linking. The
cable needed should be two core, screened
cable with XLR input and output connectors.
2For installations where the DMX ca-
ble has to run a long distance or is in an
electrically noisy environment, such as in
a discotheque, it is recommended to use
a DMX terminator. This helps in preventing
corruption of the digital control signal by
electrical noise. The DMX terminator is
simply an XLR plug with a 120 Ω resistor
connected between pins 2 and 3, which is
then plugged into the output XLR socket of
the last fixture in the chain.
Address Set ----> [Set Address Numbers]
Run Mode
----> [DMX]
----> [AUTO] ----> Auto 1- Auto2
----> [SOUND]
----> [MANUAL] ----> Manual Test ----> Function and Operation
Setup ----> [ Advanced
Setting] ---->
Pan reverse
Tilt reverse
Display
Screen Reverse
Channel (16/14/12/10CH Select)
Sensitivity (01-100)
Motor zero
Reset
Factory Set
System
Information ---->
Ver V1
DMX Address
Temperature

9
CH10 CH12 14CH 16CH Function Channel Value Description
CH1 CH1 CH1 CH1 Pan 0-255 0-540°
CH2 CH2 Pan fine 0-255 Pan Fine
CH2 CH2 CH3 CH3 Tilt 0-255 0-270°
CH4 CH4 Tilt Fine 0-255 Tilt Fine
CH3 CH3 CH5 CH5 X, Y speed 0-255 From fast to slow
CH4 CH4 CH6 CH6 LED Dimmer 0-255 From dark to bright
CH5 CH5 CH7 CH7 LED Strobe
0-7 Turn on
8-250 Strobe from slow to fast
251-255 Turn on
CH6 CH6 CH8 CH8 7 color + White
0-15 White Lighting
16-31 Color 1
32-47 Color 2
48-63 Color 3
64-79 Color 4
80-95 Color 5
96-111 Color 6
112-127 Color 7
128-191 CW from slow to fast
192-255 CCW from slow to fast
CH7 CH7 CH9 CH9 8 Static Gobos
+White
0-6 Open
7- 13 Gobo 1
14-20 Gobo 2
21-27 Gobo 3
28-34 Gobo 4
35-41 Gobo 5
42-48 Gobo 6
49-55 Gobo 7
56-63 Gobo 8
64-70 Gobo 8 shake speed from slow
to fast
71-77 Gobo 7 shake speed from slow
to fast
78-84 Gobo 6 shake speed from slow
to fast
85-91 Gobo 5 shake speed from slow
to fast
92-98 Gobo 4 shake speed from slow
to fast
99-105 Gobo 3 shake speed from slow
to fast
106-112 Gobo 2 shake speed from slow
to fast
113-119 Gobo 1 shake speed from slow
to fast
120-127 Open
128-191 Gobo Rotate CCW slow to fast
192-255 Gobo Rotate CW slow to fast
16/14/12/10/ Channel Mode Sheet

10
CH8 CH10 6 rotation gobos
+White
0-15 open
16-31 Gobo1
32-47 Gobo2
48-63 Gobo3
64-79 Gobo4
80-95 Gobo5
96-127 Gobo6
128-191 Gobo Rotate CW slow to fast
192-255 Gobo Rotate CCW slow to fast
CH9 CH11 Gobo Rotation
0-15 open
16-95 Gobo Fine 0-360
96-135 Gobo Rotating 0-90
136-155 Gobo Rotating 0-180
156-175 Gobo Rotating 0-720
176-215 Gobo self-rotating CW from slow
to fast
216-255 Gobo self-rotating CCW rotating
from slow to fast
CH8 CH10 CH10 CH12 Focus 0-255 Gobo hazy to clear
CH9 CH11 CH11 CH13 Prism 0-63 Open
64-255 Prism In
CH10 CH12 CH12 CH14 Prism Rotation
0-15 Stop
16-135 Rotate CW slow > fast
136-255 Rotate CCW slow > fast
CH13 CH15 self-setting Program
0-7 No action
8-131 Auto mode
132-255 Sound mode
CH14 CH16 Reset 250-253 Reset
10. Maintenance and Cleaning
The following points have to be considered during the inspection:
1. All screws for installing the devices or parts of the device have to be tightly connected and must not be
corroded.
2. There must not be any deformations on the housing, color lenses, fixations and installation spots (cei-
ling, suspension, trussing).
3. Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances.
4. The electric power supply cables must not show any damage, material fatigue or sediments.
5. Further instructions depending on the installation spot and usage have to be adhered by a skilled insta-
ller and any safety problems have to be removed.

11
Caution!
Disconnect from mains before starting maintenance
operation.
!
In order to keep the lights in good condition and extend the life time, we suggest a
regular cleaning to the lights:
• Clean the inside and outside lens each week to avoid the weakness of the lights due to accumulation of
dust.
• Clean the fan each week.
• A detailed electric check by an approved electrical engineer every three months: make sure that the
circuit contacts are in good condition, prevent the poor contact of circuits from overheating.
• We recommend a frequent cleaning of the device. Use a moist, lint-free cloth. Never use alcohol sol-
vents.
• There are no serviceable parts inside the device. Please refer to the instructions under “Installation
instructions”.
• Should you need any spare parts, please order them from your local dealer.

Note: All information is subject to change without prior notice.
IMPORTANT INFORMATION!
In order to optimize the recovery and recycling of the materials that old appliances contain
and reduce the impact on human health and the environment, please make sure that this
product is recycled at the end of its life.
Importer:
ACSON COMERCIAL
C/Pallars, 405
08019 Barcelona
www.acson.com
[email protected]