Electrolux R410A User manual

INVERTER SPLIT - TYPE (R410A)

Contact an authorised service technician for repair or maintenance of this unit.
Contact the installer for installation of this unit.
The air conditioner is not intended for use by young children or infirmed persons
without supervision.
Young children should be supervised to ensure that they do not play with the air
conditioner.
This air conditioner should be installed in accordance with AS/NZS 3000:2000
and your electricity suppliers rules.
There are local council rules regarding maximum allowable noise levels emitted
by air conditioners.
If the power cord is to be replaced, replacement work shall be performed by
authorised personnel only.
Installation work must be performed in accordance with the national wiring standards
by authorised personnel only. Wrong connection can cause over heating or fire.
'
Take care not to catch fingers on the fan when adjusting vertical louvres.
This air conditioner uses R410A refrigerant.

2
!
It may cause fire.
It may cause fire and electric
shock.
It may cause an explosion or fire.
Do not use the socket if it is
loose or damaged.
Do not open the unit
during operation.
!
!
!
!
!
!

3
Sharp edges could cause injury. There is danger of fire or electric shock.

Mode
Cooling operation
Heating operation
Drying operation
Temperature
1. If air conditioner is used outside of the above conditions, certain safety protection
features may come into operation and cause the unit to function abnormally.
2. Room relative humidity less than 80%, if the air conditioner operates in excess of this
figure, the surface of the air conditioner may attract condensation. Please sets the horizontal
air flow louvre to its maximum angle (vertically to the floor), and set HIGH fan mode.
3. Optimum performance will be achieved within these operating temperature.
Room temperature
Outdoor temperature
17 C 32 C 17 C 27 C 10 C 32 C
~
CAUTION:
~~
~~
~
18 C 50 C -15 C 34 C 10 C 50 C
4

AUTO
COOL
DRY
FAN
HIGH
MED
LOW LOW
TEMPTEMP
MODE ON/OFFON/OFF FAN
SWINGSWING ECONONY TIMERTIMER
RESET RESETLOCK
LOCK
R
CANCEL
DIGITALDISPLAY DIGITALDISPLAY
HEAT
AIR
DIRECTION
5

6
TIMER ON
AIR
DIRECTION
TURBO
TIMER OFF
Timer on button
Timer off button
Press the TIMER OFF button to
set the auto-off time sequence.
To cancel the auto-off time
sequence press the TIMER OFF
button until the auto-off time is
set to .
"0:00"
Press the TIMER ON button to
set the auto-on time sequence.
To cancel the auto-on time
sequence press the TIMER ON
button until the auto-on time is
set to .
"0:00"
Turbo button
Press the TURBO button
to activate the fast cooling
operation. Press again
to cancel.
Air direction button
Press the AIR DIRECTION
button to adjust the angle
of the horizontal louvre.
Press the AIR DIRECTION
button for more than 2
seconds to activate auto
SWING function. Press
the AIR DIRECTION
button again to stop the auto
SWING function.
When you press the recessed
LOCK button, all current
settings are locked-in and the
remote control does not accept
any operation except that of the
LOCK. Use the lock mode when
you want to prevent settings
from being changed accidentally.
Press the LOCK button again
when you want to cancel the
LOCK mode. A lock symbol will
appear on the bottom left hand
side of the remote control display
when the lock function is activated.
AUTO, COOL, DRY, HEAT to

7
AUTO, COOL, DRY, HEAT and FAN only (Refer to
note below) and back to AUTO.

TIMER ON
AIR
DIRECTION
TURBO
TIMER OFF
8
When you set the air conditioner in AUTO mode, it
will automatically select cooling, heating or fan only
operation depending on what temperature you have
selected and the room temperature.

TIMER ON
TIMER OFF
AIR
DIRECTION
TURBO
TIMER ON
TIMER OFF
AIR
DIRECTION
TURBO
9
Press to select COOL, HEAT or FAN only.