Electrolux XBM20 User manual

Contents
Please refer to the numbered drawings which correspond to the paragraph
numbers in the instruction manual.
GB
Introduction 1
Installation 1
Use and safety 3
Cleaning and hygiene 5
Fault nding 6
Maintenance 6
Compliance with regulations 8
Introduction
1.1 DESCRIPTION
• These beater-mixers are professional bakery/pastry maker
appliances designed for kneading, mixing and whisking all food
products. The A versions when tted in the kitchen, can be used
to power accessory machines.
AStainless steel bowl, 20/30 litre capacity
(Depending on model)
BRemovable protection screen and with additional plastic
screen
CH-type accessories hub
DHead
EControl panel
FSpeed change lever
GRaising and lowering lever
HPlanet gear
IColumn
JBowl support cradle
KFeet
• There are 3 standard tools available :
AA spiral hook for kneading dough
BA paddle for mixing
CA whisk for emulsifying
• Optional equipment :
- Strengthened 20 L whisk for di󰀩cult work
- Reduced bowl of 10L with 3 tools (models 20l)
- Reduced bowl of 20L and 30L with 3 tools (models 30l)
- Stainless steel table (height 480mm) for 20l table model.
•Optional equipment for A accessory hub versions only:
- Accessory machines (see § 3-6).
- Plate holder to collect products under the mincer, vegetable
slicer and sieve.
Installation
1 XBM20/30 GB 09 2023
09/2023
1.1b
Introduction
The User Manual contains useful information for the user on how
to work correctly and in complete safety, and is designed to make it
easier to use the machine (called “machine” or “appliance” below).
What follows is in no case intended to be a long list of warnings
and constraints, but rather as a series of instructions meant to
improve the service provided by the machine in every respect,
and particularly to avoid a series of injuries or damage to equip-
ment that might result from inappropriate procedures for use
and management.
It is essential that all the people responsible for transporting,
installing, commissioning, using, maintaining, repairing or dis-
mantling the machine should consult this manual and read it
carefully before proceeding with the various operations, in order
to avoid any incorrect or inappropriate handling that might be
result in damage to the machine or put people’s safety at risk.
It is just as important that the Manual should always be available
to the operator and it should be kept carefully where the machine
is used ready for easy and immediate consultation in case of any
doubt, or in any case, whenever the need arises.
If after reading the Manual, there are still any doubts concerning
how to use the machine, please do not hesitate to contact the
Manufacturer or approved After Sales Service provider, who is
constantly available to ensure quick and careful service for im-
proved machine operation and optimum e󰀩ciency.
Note that the safety, hygiene and environmental protection stan-
dards currently applicable in the country where the machine is
installed must always be applied during all phases of machine
operation. Consequently it is the user’s responsibility to ensure
that the machine is operated and used solely under the optimum
safety conditions laid down for people, animals and property.
ATTENTION!!
Machine storage: -25°C to +50°C
Ambient temperature during operation: +4°C to +40°C
This machine is for professional use and must be used by sta󰀨 trained to use, clean and maintain it, in terms or reliability and safety.
Use the machine in adequately lit premises (See applicable technical standard for the country of use. In Europe, refer to standard
EN 12464-1)
When handling the machine, always check that the parts taken hold of are not mobile elements: risk of dropping and injury to the
lower limbs.
The machine is not designed for use in explosive atmospheres.
The reference language for these instructions is French.

2.2INSTALLATION
• The 20/30 litre mixers are oor-standing only.
• To chock or level the beater:
- Remove the foot end piece before adjusting.
- Screw with a screwdriver so that the adjustable pad makes
contact.
- Check it is stable by running the beater at high speed with its
beater. Where necessary, the adjustment can be ne-tuned
with the machine running.
- Ret the plug.
• To x the beater to the oor: x by the rear feet
- Remove the end pieces from the 2 rear feet.
- Mark the 2 holes to be drilled (Ø8 max. screw, min. length 80,
plugs not supplied).
Note : It is also possible to x to the oor by the front feet,
by removing the adjustable pad.
• The 20 litre table mixers can be installed on:
- perfectly stable, non resonant support (unit, table, etc) of height
between 350 and 500 mm.
- an optional stainless steel table with storage shelf.
• To install, proceed as follows:
- Remove the adjustable pads from the front feet.
- Line up the 4 feet xing holes on the mixer with those on the
table.
- Fix the mixer on the table using the screw set provided.
• To chock or make the table level:
- Unscrew the screws xing the pads (13 mm pipe wrench).
- Adjust the pad, then lock in position.
- Check for stability by running the mixer at high speed with its
paddle.
• To embed the table in the oor :
- Counter drill the pad xing holes (plugs and screws max ø 8,
length min 30, not supplied).
2.2a
2.2c
2.2b
2.1 DIMENSIONS - WEIGHT (for information only)
AGross weight when packaged (kg)
BNet weight equipped (kg)
CPackaging dimensions (mm) L x W x H
DMachine dimensions: L x W x H (mm)
EDimensions for beater bedding: E x E1 x E2 (mm)
Hp Accessories hub height (A models)
. Handling - Transport
- The beater is delivered xed to a wooden pallet.
- Use a forklift truck to remove it from the pallet, slipping the
forks beneath the feet.
If unloaded manually, take all necessary precautions to
ensure the appliance does not tip at all
2.3 ELECTRICAL CONNECTION
ATTENTION!!
Connection to the electrical power supply must be done according to proper professional practice by a qualied and authorised
person (see current standards and legislation in the country of installation).
If an adapter is used on the socket, a check must be made that the electrical characteristics of this adapter are not lower than
those of the machine.
Do not use multiple plugs
The AC power supply to the machine must comply with the following conditions (EN60204-1);
- Maximum voltage variation: ±10%
- Maximum frequency variation: ±1% on a continuous basis, ± 2% over short periods
ATTENTION: the electrical installation must comply (for design, creation and maintenance) with the legal and standard
requirements in the country where used.
- Check that the electric mains voltage, the value shown on the specication plate.
- The machine’s electrical power supply must be protected against voltage surges (short-circuits and excess voltages) by using
fuses or thermal relays of the appropriate gauge relative to the place of installation and machine specications – see the spe-
cications shown in column F of gure 2.3a
ATTENTION: Concerning protection against indirect contact (depending on the type of power supply provided and
connection of the exposed conductive parts to the equipotential protection circuit), refer to point 6.3.3 of EN 60204-1
(IEC 60204-1) with the use of protection devices for automatic shut-o󰀨 of power in the event of an insulation fault with
a TN or TT, system, or for the IT system, with the use of a permanent insulation or di󰀨erentials controller for automatic
shut-o󰀨. The requirements of IEC 60364-4-41, 413.1 must apply for this protection.
For example: in a TT system, a di󰀨erential circuit breaker must be installed upline of the power supply, with a suitable
power cut-o󰀨 (e.g.: 30 mA) on the earthing installation for the place where it is planned to install the machine.
ATTENTION: Failure to comply with these instructions means the customer runs the risk of machine failure and/or acci-
dents due to direct or indirect contacts.
XBM20/30 GB 09 2023 2

• Motor specications:
BNumber of phases (1 single phase or 3 three-phase)
CNominal voltage in volts (value, range or commutation)
DFrequency (Hertz)
ENominal rating (Watts)
F Rating of the fuse of the mains cable (Amperes)
1) Three-phase motor
• A standard wall socket with 3 poles + Earth, rated at 20A com-
pliant with IEC60309 will be required and a matching watertight
plug tted to the power supply cable.
• Check the direction of rotation:
- of the planet gear, anti-clockwise direction (see arrow on
head)
- of the tool, clockwise direction.
• If the direction of rotation is reversed, change over the two
phase wires on the plug.
• Connection is made at higher voltage for 400V). For
connections to lower voltage supplies 230V proceed as
follows:
- Unplug the machine.
- Remove the rear plate.
- Refer to the wiring diagram in § 6.6.
This appliance must be earthed with a green/yellow wire.
- Change over the integral plate wire by moving the cable lug
from the terminal marked for the higher voltage (400V) onto
that for the lower voltage (230V).
- Change over the plate straps on the terminal plate.
- Check the direction of rotation and ret the plate.
2) Single phase motor
• A standard single phase wall socket with 2 poles + earth, rated
at 10/16 A will be required.
• The direction of rotation is factory-set.
2.3a
2.3b
2.3c
Use and Safety
3.1 OPERATION - SAFETY
• The user’s safety is ensured by:
- The motor stopping on opening the protection screen.
- The design of the screen which allows products to be added
while working in complete safety.
- The motor stopping on lowering the cradle. It will not start again
by pressing the START button.
- The START button needing to be pressed after a stoppage
(“voltage loss” device).
- The motor being protected against overload by a thermal sensor.
- Following the instructions in this manual for using, cleaning
and maintaining the machine.
• Control panel
AReduce time setting on timer
BIncrease time setting on timer
CSTOP button
DSTART button
ETimer display
•The beaters are normally started if the bowl support cradle
assembly is in the working position.
- The protection screen is tted and closed.
- The timer is set to continuous or timed operating mode.
- The bowl is in position on the cradle.
a) Timed operation
- Select time on Eby pressing buttons Aand B
- Start by pressing button D
- Stop at the end of the time set, or by pressing button C.
Note:
- To change the time being counted down, press on
button C then change using buttons A and B;
resume cycle by pressing button D.
- The time displayed at the beginning of the cycle remains in
memory
- To permanently interrupt a cycle underway, press button C twice.
b) Continuous operation
- Select --- on Eby pressing and holding button A
- Start by pressing button D
- Stop by pressing button C
3.1
To PAT test the Electrolux Range of Food Preparation Equipment,
the PCB board needs to be disconnected before any test is done.
This is due to the fact that the boards are tted with a grounding
diode that can give incorrect result during such a test. Also on a
standard appliance a ash test of 25 amps and up to 3000v is
used but, as you would expect, to use this on equipment, which
has a printed circuit, board would be quite destructive to that
board. We would recommend the use of a PAT tester approved
for computer systems which use a lower rate of amps.
The appliance is perfectly safe and is CE certicated. There are
two ways to get overcome this problem.
· Disconnect the board as instructed and test using test for PC’s,
· Or install the mixer on a fused spur (no plug) as this takes it
away from being a portable appliance and the PAT test is then
not needed.
ATTENTION!!
Clean the machine properly prior to its rst use
Uncontrolled closure of the lid or ram press involves a risk of crushing the ngers.
Never put a hand in the work area while the machine is in operation; risk of injury. It is strictly forbidden
to put the safety systems out of action or modify them: Risk of permanent injury!!!!
Check that the safety devices operate correctly each time before using (see paragraph on «safety system checks»).
Never put a hand, a hard or frozen object in the appliance
For health and safety reasons, always use a strong washable or disposable head covering that covers the hair completely.
3 XBM20/30 GB 09 2023
Do not use the machine without the bowl.

• To ret:
- Line the shoes up with the slots in the screen crown.
- Press upwards and turn in an anti-clockwise direction (1
complete turn) until locked on the stop (binding spot).
Note: The screen stays in position on its own from the
start of turning.
THE BEATER CAN ONLY BE STARTED IF THE
SCREEN IS PROPERLY CLOSED AND LOCKED.
3.2 RAISING - LOWERING THE PROTECTION
SCREEN
To make cleaning easier, the rotating protection screen can be
removed and the plastic screen which covers.
• To remove it:
- Stop the machine, lower the cradle and remove the tool and
the bowl.
- With the screen locked, turn it in a clockwise direction (1
complete turn) until it is on the stop.
- The screen unhooks downwards and is released.
- The plastic screen can be removed by removing the wire screen
(for use without our).
THE BEATER CANNOT BE STARTED WHILE THE
SCREEN IS REMOVED.
3.3 FITTING THE BOWL AND THE TOOLS
•Proceed as follows:
- Lower the cradle to the down position, pushing the lever G
backwards.
- Put the tool inside the bowl.
Note: Make sure the handle rests are clean (see § 4-2).
- Present the bowl onto the cradle.
- Engage the bowl ball-and-socket in the cradle housing and
lower the bowl vertically to position the two cradle pins in the
handle holes.
- Slide the tool onto the tool-holder and twist it in an anti-clockwise
direction to lock it.
- Pull the lever G towards you to raise the bowl to the work
position.
- Close the protection screen.
- Press the START button.
3.3a
3.3b
3.4 CHANGING AND SELECTING SPEEDS
• The drive belt variable speed gives the user a continuous range
of speeds to carry out all sorts of work while giving highest output
and quality.
To change speeds, proceed as follows:
- Press the START button.
- Pull the lever towards you to decrease the speed and push it
away to increase it.
- Always start with a slow speed to prevent splashes or our
dust being given o󰀨 and then gradually increase the speed
bearing in mind that the drive force (torque) increases as the
speed decreases.
Never move the speed lever when stopped
Note:
The lever stays at the speed selected thanks to its any-po-
sition self-maintaining system.
- If the drive belt slips, decrease the speed.
- When the work is nished, bring the lever back to the slow
speed position, press the stop button and then lower the bowl
(see § 3-3).
• Speed for using the tools
VSpeed at the planet gear (rpm)
AHard dough
BSoft dough
Recommended work
3.4a
3.4b
3.5 MAXIMUM CAPACITIES
• The beater’s working capacity depends on:
- The tool used. ?
- The nature, quantity and density of the matter to be worked.
- The optimum speed for quality work.
• Too great a quantity will always be detrimental to the quality of
work and the service life of the beater’s mechanical components
and may lead to overheating of the motor and it stopping suddenly.
(see § 5-1).
Product Reference Bowl (L) Tool
10/20/30
Flour/water paste
( 60% Hydratation) Kg our 3/6/8
Pizza
(40% Hydratation) Kg dough 2,5/5/6
Short-crust pastry 2,5/5/6
Sweet pastry 2/4/5
Croissant dough Kg our 2,5/5/6
Brioche dough 2,5/5/6
Chou pastry L. water 2/4/5
Meat Kg 5/10/15
Purée Kg potatoes 5/10/15
Fondant kg sugar 3/6/8
Egg whites 16/32/50
Genoese numbr of eggs 15/30/45
Biscuits 15/30/45
Meringues Kg sugar 0,75/1,5/2,5
Recommended maximum quantities
XBM20/30 GB 06 2015 4
3.2a
3.2b
3.2b
§5.3

3.6 ACCESSORIES HUB
• Version A beaters are tted with an H12-type variable speed
drive take-o󰀨 to power the following optional accessories:
- H 70 H and HV 82 H: Ø70 and Ø82 mm mincers, ENTERPRISE
or UNGER system. Supplied with hopper, pestle, knives and
discs.
- CX 21 H: Vegetable slicer tted with discs for cutting up to 8
mm, thin slicing, shredding, grating, etc.
- P 200 H: Food processor for purées, soups, compotes, sh
soups, etc. Supplied with 3 di󰀨erent grids.
•To install an accessory, proceed as follows:
- Fit the accessory depending on the work to be carried out.
Refer to the separate instructions for each accessory
machine.
3.6a
3.6b
3.6a
3.6a
The machine must be stopped in slow speed using the
stop button before tting or removing the accessory.
- Raise the cover H.
- Present the accessory B and introduce the cone C into the
beater hub A.
- Engage the male square section D into the hub A drive shaft,
turning B.
- Position the pin E opposite the housing I and push the acces-
sory rmly into hub A.
- Tighten the locking screw G (clockwise direction ) in the
recess F.
- Select the speed according to the accessory.
Note:
To remove the accessory, unscrew G a minimum of 4
turns to release from the recess F.
• Speeds to be used for the accessories:
VP = Accessory hub speed (rpm)
Recommended work
Cleaning and hygiene
4.1 IN-BETWEEN USE
• Remove the bowl and the tool
• Wash the inside of the bowl and the tool in a basin using hot
water with a disinfectant or de-greasing (if working with greasy
products) detergent added, then rinse with clean water and dry.
• Clean the planet gear holder, the tool-holder shaft and the pro-
tection screen using a damp sponge and a detergent / disinfectant
product, then rinse in clean water.
• Oil the accessory shaft (cooking oil or grease).
Note: Use cleaning products which are compatible with
aluminium parts.
4.2 AFTER USE
• Unplug the machine.
• Remove the bowl, tool and protection screen.
• Wash the bowl and the tools in a basin with a disinfectant or
de-greasing product, then rinse with clean water and dry. Only
the bowl can be cleaned in a dish-washer.
• The full protection screen is not dishwasher-safe.
• Clean the planet gear holder, tool-holder shaft, protection
screen and cradle paying particular attention to the bowl edges
and where necessary the outside of the beater using a damp
sponge and a detergent / disinfectant product, then rinse.
• Oil the accessory shaft (cooking oil or grease).
• Check the various elements are properly clean.
Note: make sure that the cleaning products used are
compatible with the appliance element materials.
-Do not use abrasive detergents as these could scratch
the surfaces.
- To clean the accessory machines, refer to the instructions for
each accessory.
• Periodically: (at least once a month).
- Remove dust from the ventilation holes at the back of the
machine (a cause of overheating).
- Wipe and lightly oil the raising and lowering pillars with Va-
seline.
Never wash the machine with a pressure cleaner.
ATTENTION!!
Before dismantling any part, disconnect the appliance from the power supply.
Before using any cleaning product, be sure to read the instruction and safety instructions accompanying the product and use
appropriate protective equipment.
Do not clean the machine with a pressure cleaner
4.3STRAY FLOUR PARTICLES:
In order to reduce the emission of stray our particles while loading
the bowl, it is recommended as follows:
- Empty the our bag or the container containing the our without
shaking it.
- Pour in the water before putting the our in if that is possible
- Always start at slow speed during the water/our mixing
- Do not shake an empty our bag. Roll it with care.
- The see-through plastic screen supplied with the machine must
be used.
Keeping to these simple rules will contribute to reducing the
emission of our dust and consequently reducing the risks of
allergy linked to that dust.
5 XBM20/30 GB 04 2019

5.2 NOISE OR ABNORMAL OPERATION
• Metallic noise
- Bent tool or tool rubbing or turning the wrong way round
(see § 2-3).
- Damaged bowl or bowl not in place (see § 3-3)
- Lack of grease on planet gear (see § 6-4 for removal).
•Grating noise
- Drive belt slipping causing it to wear quickly (see § 6.2
for replacement).
- Defective drive belt (see § 6-2 for its replacement)
•Lack of power
- Check the guides and pulleys are sliding properly and the
condition of the drive belt (see § 6-2)
- Motor running on two phases (see § 6-6).
- Incorrect power supply voltage with overheating of the motor.
- Too high working speed: lower the speed
- Overloaded: reduce the quantity.
If the problem persists, contact your dealer’s maintenance
department.
5.3 TOOL STICKING ON TOOL-HOLDER SHAFT
• Generally caused by incorrect cleaning or warping of the tool
after a knock.
• If starting to jam, do not force but oil or use penetrating liquid
and wait a moment for the product to work.
• Gradually work in measured steps:
- By turning using and to-and-fro movement.
- By tapping on the tool with a mallet after having freed the pin
from the bayonet.
- Rub down the warped part with abrasive cloth where required.
If the problem persists, contact your dealer’s maintenance
department.
5.4 SPEED CONTROL LEVER
• If the speed control lever becomes sti󰀨:
- lightly oil the variable pulley spindles and grease the sliding
gear drive pin.
• If the lever no longer stays in position automatically, refer to §
6-3 speed adjustment.
If the problem persists, contact your dealer’s maintenance
department.
Maintenance
6.1 MECHANISM
• It is recommended that the following is carried out at least once
a year:
- Where necessary, grease the planet gear pinions with very
adhesive grease (refer to us, see § 6-4).
- Clean out the dust from the drive belt and our dust from the
inside of the machine using a vacuum cleaner.
• Access to the electrical components:
- unplug the machine.
• The capacitors may remain charged with electricity. To prevent
any risk when working on the machine, it is recommended that
they are discharged by connecting across their terminals with an
insulated conductor (a screwdriver, for example).
Residual current on the capacitor terminals
Fault nding
5.1 THE BEATER WILL NOT START:
• Check that:
- The beater is plugged in properly.
- The socket is correctly supplied with electrical power.
- The bowl is in the working position and the protection screen
closed.
- The bowl is in position on the cradle.
• If the machine stops while running:
- The motor thermal sensor has tripped. Wait for a few
minutes before restarting.
- Decrease the speed or the load (see § 3.3 and 3.4)
ATTENTION!!
Unplug the machine before carrying out any operation.
Maintenance may only be carried out by a qualied, trained and authorised person.
XBM20/30 GB 06 2015 6

6.4 REMOVING THE PLANET GEAR
- Remove the protection screen and the cover after disconnecting
it.
- Remove the drive belt.
- Put a piece of wood between the bowl and the planet gear to
hold the planet gear.
- Remove the driven pulley and its key.
- Remove the accessories hub if the model has one.
- Remove the planet gear assembly by tapping it with a mallet
on the top of the sun gear shaft and lowering the bowl as
necessary.
6.2
6.4
6.5 CHECKING THE SAFETY DEVICES
• The correct operation of the safety devices should be checked
frequently. The motor should stop on opening the protection
screen and on lowering the bowl.
• If either of these functions does not occur:
- Do not use the machine.
- Have it adjusted by your dealer’s maintenance depart-
ment.
6.6 ELECTRICAL COMPONENTS
• Check the condition of the cable and electrical components
regularly.
6.7 ADDRESS FOR MAINTENANCE
In the rst instance, we advise you to contact the dealer who
sold you the machine.
· The manufacturer reserves the right to change and make im-
provements to its products without prior notice.
For any information or orders for spare parts,
state the type of machine, the serial number
and the electrical specications.
Dealer’s stamp
Date of purchase:
6.3 SPEED ADJUSTMENT
In normal operation, on changing from high speed to low speed,
the lever moves back slightly before locking in position.
• If this does not happen, carry out the following adjustment:
- Run the beater at slow speed (1) and stop it.
- Unscrew the speed change lever.
- Remove the cap to gain access to the mechanism and re-tighten
the lever.
- Release the anti-slip screw A lock-nut.
- Start the beater again and unscrew the anti-slip screw until the
lever is held at all speeds.
- Re-tighten the lock-nut.
- The beater is set in the factory to operate at approximately 35
to 180 rpm (planet gear speed).
7 XBM20/30 GB 09 2023
6.3
The machine must not operate if the bowl is
not in position on the cradle.
6.2 CHANGING THE DRIVE BELT
- Stop the beater in high speed (position 8) and unplug it.
- Remove the casing top cover retaining screws and disconnect
it to separate it from the head.
- Hold the drive belt by the sides and pull towards you until it is
released from the driven variable pulley.
- Then free it from the drive pulley.
- Lightly oil the motor shaft and variable pulley driven shafts with
Vaseline.
• To t the new drive belt:
- Present the drive belt to the drive pulley.
- Pull rmly to engage it as far as possible.
- Engage the drive pulley onto the driven pulley.
- Turn the driven pulley by hand to centre the drive belt.
6.2

Compliance with regulations
The machine has been designed and manufactured to
comply with:
- Machine directive 2006/42 EEC
- Machine directive CEM 2014 / 30 EU
- 2011/65/EU Directive on the restriction of the use of certain
hazardous substances
2002/96/CEE « WEEE »
The symbol « » on the product indicates that this product may
not be treated as household waste. Instead it shall be handed
over to the applicable collection point for the recycling of electrical
and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences
for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product. For
more detailed information about recycling of this product, please
contact the sales agent or dealer for your product, your after-sales
service, or the appropriate waste disposal service.
2006/12/CEE“Waste”
The machine is designed so that it does not contribute, or as
little as possible, to increasing the quantity or harmfulness of the
waste and the risks of pollution.
Make sure to observe the recycling conditions.
94/62/CEE “Packaging and packaging waste”
The packaging for the machine is designed so that it does not
contribute, or as little as possible to increasing the quantity or
harmfulness of the waste and the risks of pollution.
Make sure to eliminate the various parts of the packaging in
appropriate recycling centres.
- To the European standards:
EN 454- machine - mixers. Safety and hygiene regulations
This conformity is certied by:
- The CE compliance mark attached to the machine
- The corresponding CE compliance declaration associated with
the warranty.
- This instruction manual, which must be given to the operator.
Acoustic specications:
- The acoustic pressure level measured in conformity with the
EN ISO 3743.1-EN ISO 3744 < 70 dBA.
Protection indices as per the EN 60529-2000standard:
- IP55 electrical controls.
- IP23 overall machine.
Integral safety devices:
- The machine has been designed and manufactured in accordance
with the relevant regulations and standards shown above.
- Before using the machine, the operator must be trained to use
the machine and informed of any possible residual risks.
Food hygiene:
The machine is made from materials that comply with the following
regulations and standards:
- Directive 1935/2004/CEE: materials and objects in contact with
foodstu󰀨s
- Standard EN 601- : cast aluminium alloys in contact with
foodstu󰀨s.
- Directive EN 1672-2- : Prescriptions relating to hygiene
The surfaces of the food area are smooth and easy to clean.
Use detergents that are approved for food hygiene and follow
the instructions for their use.
XBM20/30 GB 05 2016 8