Electrolux EWE602IX1DWX3 User manual

EN MULTI-POINT ELECTRIC
WATER HEATER
USER MANUAL
electrolux.com/shop EWE602IX1DWX3
EWE802IX1DWX3

2
www.electrolux.com
1. PARTS IDENTIFICATION................................................................................................................. 3
2. SAFETY INFORMATION..................................................................................................................
4
3. HEATER UNIT INSTALLATION....................................................................................................... 5
4. PLUMBING PROCEDURE...............................................................................................................
7
5. ELECTRICAL INSTALLATION.........................................................................................................
8
6. TEST RUN............................................................................................................................................
10
7. MAINTENANCE.................................................................................................................................
10
8. WIRING DIAGRAM...........................................................................................................................
11
9. ELECTRICAL SPECIFICATION........................................................................................................
11
1. Front Cover
2. LED Indicator
3. Temperature Control Knob
4. ELCB Reset Lever
5. ELCB Test Lever
6. Heater Base
7. Thermostat
8. Heater Tank
9. Water Outlet Connection
10. Rubber grommet
11. ELCB
12. Main PCB Board
13. Water Inlet Connection
14. Pressure Relief Valve
15. Discharge Pipe ( Not provided by Manufacturer )
16. Mesh Filter
17. Terminal Block
18. Rating Label
WE’RE THINKING OF YOU
Thank you for purchasing an Electrolux appliance. You’ve chosen a product that brings with
it decades of professional experience and innovation. In genious and stylish, it has been
designed with you in mind. So whenever you use it, you can be safe in knowledge that
you’ll get great results every time. Welcome to Electrolux.
Visit our website to:
Get usage advice, brochures, trouble shooter, service information:
www.electrolux.com
Register your product for better service:
www.registerelectrolux.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.electrolux.com/shop
CUSTOMER CARE AND SERVICE
We recommend the use of original spare parts.
When contacting Service, ensure that you have the following data available.
The information can be found on the rating plate. Model, PNC, Serial Number.
Warning/ Caution-Safety information.
General information and tips.
Environmental information.
Subject to change without notice.
CONTENTS 1. PARTS IDENTIFICATION
1
17
1
1
3
1
2
1
3
1
14
1
15
1
16
1
14
1
15
1
16
1
6
1
8
1
7
1
9
1
10
1
12
1
13
1
5
1
4
1
11
3ENGLISH
Fig. A
1
18
1
18

Fig. 1 Fig. 2
Fig. 3 Fig. 4
196mm
272mm
102mm
Mounting hole A
Mounting hole B
HEATER UNIT INSTALLATION DIAGRAM
5ENGLISH
4www.electrolux.com
2. SAFETY INFORMATION
3.
HEATER UNIT INSTALLATION
Mounting hole C
TABLE 1 - CABLE SIZE TABLE
(AC)
Voltage Power Current Conductor Size (csa) On/ Off Fuse /
(kW) (A) mm Conduit
Cable
Flexible
Cable Switch (A) MCB (A)
220V ~
50/60 Hz 6.0 27.3 4.0 7 / 0.85mm 56 / 0.30 mm 32 32
220V ~
50/60 Hz 8.0 36.4 40 40
6.0 7 / 0.85mm 56 / 0.30 mm
2
3.1 Installation instruction for the qualified installer
.
.
.
.
Install the Heater Unit as close as possible
to main hot water draw-off points.
Leave a minimum of 5’’ of clearance on all
sides for servicing.
Remove plastic cover. (Fig. 3)
Mount Heater Unit securely to wall by putting
two screws through mounting holes.
Screws and plastic wall plugs for mounting
are provided. (Fig. 4)
3.2 The Heater Unit is to be installed in
a closed, frost-free room. The Heater Unit
is to be installed vertically (Hot water
connection downwards).
3.3 The Heater Unit can be installed in
any location, concealed in the ceiling,
below washbasin or even wall mounted.
2.1 Products manufactured by Electrolux are safe
provided they are installed, used and maintained
in good working order in accordance with our
instructions and recommendations. Alwaysrefer
to this manual if you have any doubt.
2.2 The Electric Water Heater must be earthed.
Improper grounding could cause electrical shock.
2.3 If any of the following conditions occur as
shown below, immediately switch off the power
supply and contact the Electrolux Consumer
2.4 When the Electric Water Heateris
used by someone such as child, elderly
person, sick person and physically
handicapped person, the person
concerned is kindly requested to pay
attention and check the shower
temperature by hand from time to time.
2.5 During lightning/thunder, switch off the power
supply to the Electric Water Heater in advance to
protect the Electric Water Heater against possible
damage.
2.6 The earth continuity conductor of the electrical
installation must be effectively connected to all
exposed metal parts of other appliances and
services in the room, which in the Electric Water
Heater is to be installed to conform to local
regulations and ensure proper earthing/grounding
for ELCB to be effective.
NOTE : When removing the Electric Water Heater
from package, a small amount of water may be
found inside. This is normal as the Electric Water
Heater is tested during manufacturing process.
WARNING !
.
.
.
.
.
If the Electric Water Heater begins to make an
odd noise, smell or smoke.
If ELCB trips and Electric Water Heater Indicator
does not light up.
Water temperature cannot be controlled.
If the Electric Water Heater shows signs of a
distinct change in performance.
If water leaks from inside.
2.8 Installation must be carried out by a
qualified personnel and in compliance local
2.9 This Electric Water Heatermust be
permanently connected to the direct main line
supply. A plug and socket is not recommended
to be used.
2.10 For the correct size of wire conductor
corresponding to different electrical loadings,
2.11 This Electric Water Heateroperates at a
minimum water flow rate of 2.0 litre/min and
maximum working pressure of 6 bars. For
direct connection from the water tank, the
2.12 The Electric Water Heaterwill not function
if there is insufficient water flow (min 2.0 litre/min)
2.13 The built-in ELCB will automatically cut off
the power supply in case there is a current
2.14 The thermostat will automatically cut off the
power supply if it has sensed an abnormal rise in
water temperature.
CAUTION !
authority regulations.
please refer to Table 1.
Electric Water Heatermust have an
installation minimum 1.0m below the water tank.
to trigger the flow switch.
leakage from 15mA.
Care Center. Never attempt to repair the Electric
Water Heater yourself:
User is advised to test and adjust the
water temperature before using.
2.7 WARNING : Metallic / chromed hose and
conductive control valve shall not be used.
Caution :In order to avoid ahazard due to
inadvertent resetting of the thermal cutout, this
appliance must notbe supplied through an
external switching device, such as a timer, or
connected to a circuit that is regularly switched
on and off by the utility.
2.15 Electric MultipointWater Heater with high
power (8.0 kW) may come up with high temperature
water outputwhen taking shower (only1output
pointisin use) whileother outputpoints are notin
use at the same time. Always check and adjust
water temperature before using ishighly
recommended.

Fig. 5
Note: When connecting the Pressure Relief Valve to thewater inlet, pleasemake sure the discharge
nozzleis facingdownward. Connect a discharge pipe (PVCtube of dia.8.0mm)tothedischargenozzle
in a continuosly downward direction and this pipe must be left open to the floor drain exhaust or discharge
pipe.In abnormal condition where pressure gets higher than 6.0 bars, water will drip from this discharge pipe.
Pressure Relief Valve must be installed to
inlet every time. Refer picture in Fig. A.
Pressure
relief valve
Main
water
supply
Hot
water
outlet
Separate
permanently
connected
supply
from consumer
unit (DB)
Heater Unit installed
above ceiling /
below washbasin /
wall mounted
Cold
water
outlet
Double poles
Heater Switch/
Isolator
6www.electrolux.com
7ENGLISH
3. HEATER UNIT INSTALLATION (CONT ’D)
4. PLUMBING PROCEDURE
4.1 Connect Pressure Relief Valve to INLET of
Heater Unit. Usesealing tape for the connection
to prevent water leakage. DO NOT apply excessive
force when tightening the Pressure Relief Valve.
4.2 Insert Mesh Filter Washer before connecting the
incoming water supplyto the Pressure Relief Valve.
4.3 If in any case, make sure toput the Mesh Filter
between theheater unit inlet pipe and Pressure Relief
Valve.
4.4 Turn on the water mains to drain out all plumbing
dirts before connecting the water supply to the Heater
Unit, the water supply to the Heater Unit must be
free from mud and dirt. Always KEEP the water
supply to the Heater Unit free from mud and dirt at all
time during usage.
N ote:When connecting the Pressure Relief Valve to the
water inlet, please make sure the discharge nozzle is
facing downward. Connect a dischargepipe (PVC tube
of dia. 8.0mm) to the dischargenozzle in a continuously
downward direction and this pipe must be left open to the
floor drain exhaust or dischargepipe.In abnormal
condition where pressure gets higher than 6.0 bars, water
will drip from this discharge pipe.
4.5 The water inlet and outletmust be installed
correctly, otherwise theHeater Unit will not function.
4.6 Do not applyplumbing cement on connection.
Whenever necessary, use only thread or sealing tape.
4.7 Heater Unit must be installed in a vertical position
with the water fittings pointing downward. Do not install
unit where it would routinelybe splashed with water.
Electric shock may result.
THE HEATER TANK MUST BE FILLED UP
WITH WATER BEFORE TURNING ON THE
ELECTRICITY SUPPLY TO PREVENT ANY
DRY BURNT DAMAGE TO THE HEATING
ELEMENT. CHECK FOR ANY WATER
LEAKAGE.
Note: Connections to the Multi-point hot system should
be limited to 2 or at the most 3 outlet usage point and
they should be near to each other, e.g. in the same
bathroom but only ONE OUTLET POINTS IS TO BE
USED AT ANY ONE TIME. Extensive distance between
the appliance and usage point(s) will result not only in
loss but also slow response of obtaining the hot water
at the point(s) (Fig.5).
WARNING!
CAUTION! IMPORTANT

Fig. 6
Fig. 7
Fuse Distributor Board
Miniature Circuit Breaker (MCB)F US E
ON / OFF Double Pole Switch ON/OFF
DoublePVC Cable
Cable
NOTE: Refer to Table 1
for electrical loading
and correct size of
wire conductor
Position
this way
Screw A
METHOD OF ALIGNMENT WHEN REPLACING FRONT COVER
ELECTRICAL INSTALLATION DIAGRAM
(O Position)
8www.electrolux.com
5. ELECTRICAL INSTALLATION
5. ELECTRICAL INSTALLATION (CON
’D)
Screw A
Position
this way
(O Position)
‘A’
Brown or red: LIVE (L)
Blue or Black: NEUTRAL (N)
Green or Green/Yellow: Earth ( )
Ensure the power cord
DOES NOT touch
copper ange
Fig. A Fig. B
9ENGLISH
‘B’
5.1 Allelectrical work must comply with national and
applicable state and local electrical codes.
5.2 This appliance must be earthed. Improper grounding
could cause electrical shock.
5.3
5.4
5.5 Usedouble insulation cable of over 4mm.
5.6
Remember to SWITCH OFF the mains before
carrying out any electrical work.
Refer to TABLE 1 for the correct cable size.
Insert the wall embedded cable through Side Entry ‘A’
by cutting a hole at the source cord rubber holder and lead
the cable to Cable Bracket ‘B’ (Fig. 7).
WARNING!
2
5.7
Connect the cable as follows:
Brown or Red: LIVE (L)
Blue or Black: NEUTRAL (N)
Green or Green/Yellow: EARTH ( )
PROCEDURE :
5.8 Clamp the cable to the correct position.
CHECK IF THE WIRING CONNECTION IS
CORRECT and replace the cover.
5.9 When putting back the Front Cover,
please take note of the
procedure shown below :
-Ensure the position is correct, turn the
Temperature Control Knob Insert to OFF
position as shown in Fig.A (At the Heater Base)
-Install the Front Cover,turn the Temperature
Control Knob to OFF position to align with the
VR shaft as shown in Fig.B (At the Front Cover)
5.10 Fix the Temperature Control Knob and
screw ‘A’ .

Fig. 8
2.1 Kg (6.0kW model) / 2.3 Kg (8.0kW model)
ELCB TESTING
WIRING DIAGRAM - ELECTRICAL CONTROL WITH ELCB EWE602IX1DWX3
SPECIFICATIONS (TABLE 2)
ELECTRICAL LOADING
WATER CONNECTION
DIMENSIONS
WEIGHT
MIN. WATER FLOW RATE
TYPE
6.0kW, 220V ac (single element) / 8.0kW , 220V ac (double element)
Electronic power control
3 Liter / min.
1/2’’ bsp multipoint system
272 x 196 x 102 (mm)
printing and may be subjected to change without prior notice.
ELCB Test Lever
ELCB Reset Lever
6. TEST RUN
11ENGLISH
10 www.electrolux.com
7. MAINTENANCE
8. WIRING DIAGRAM
9. ELECTRICAL SPECIFICATION
E
N L
T2
G
N1
TRIAC
Manual Reset
Thermal
Cut- Out
& Thermostat
Heater
Tank
Power ON/OFF
Temp. Control Flow
Switch
FS
FS
LED BOARD
T2
N
2P ELCB
30A
15mA,
<0.1s
E
WIRING DIAGRAM - ELECTRICAL CONTROL WITH ELCB EWE802IX1DWX3
E
N L
T2
G
N1
TRIAC
Manual Reset
Thermal
Cut- Out
& Thermostat
Heater
Tank A
Power ON/OFF
Temp. Control Flow
Switch
FS
FS
LED BOARD
T2
N
2P ELCB
40A
15mA,
<0.1s
E
Heater
Tank B
6.1
6.2
6.3
6.4
Turn on the water supply and Stop
Valve, the water will flow through the outlet.
Switch on the power supply. The 2 LED
Indicator light shall run ON/OFF 3 times in
sequences to indicate the set are self checking.
If the Heater Unit is not earthed properly, the
Earth Led indicator light will OFF, during usage
or standby. Earth Led indicator light also
OFF if Live & Neutral reverse connection.
Turn the Temperature Control Knob to
‘ON’, the Red (Power) LED Indicator will light up
, hot water will flow out within a few seconds.
The more Temperature Control Knob is turned
in clockwise direction, the hotter is the water.
The shower bath, long bath, wash basin
might not be hot enough even at the ‘MAX’
position if incoming water supply from the mains
is too cold or the pressure of water is too high. In
this case, you may adjust the incoming cold water
mixer valve to reduce the water inflow in order to
get the desired water temperature.
6.5 Check the Built-in ELCB as follows:
Pull the ELCB TEST LEVER down, the
Built-in ELCB should trip and cut off the
power supply, Red and Green
LED Indicator should light off.
Pull the ELCB RESET LEVER down to
reset the ELCB, the 2 LED Indicator light
shall run ON/OFF 3 times in sequences to
indicate self checking and the Heater Unit
should resume normal function, the Green
LED Indicator should light on. If procedures
stated above prevailed, the ELCB is
functioning in normal condition.
.
.
It is unnecessary to turn the Temperature
Control Knob to ‘OFF’ position when the Heater
Unit is not in use.
Explain to the user how the unit works
and familiarise him or her with its use.
Advise the user about possible hazards
(high water temperature)
Hand over these instructions, to be kept in a
safe place.
.
.
6.6
6.7
Read the section ‘SAFETY INFORMATION’ first.
Test the ‘ ELCB ’ regularly
7.1
Clean the filter regularly
7.2 Clean the Mesh Filter regularly to prevent blockage.
When carrying out any work, isolate the unit from the mains
and shut off the water connection.
7.3
Cleaning precaution!
7.4 Do not use thinner, alcohol, petrol or any other
organic solutions to clean the set. Use only dampeded cloth
with mild detergent.
This procedure is a highly recommended test to be
carried out at least once a month. Turn on the power supply
and water supply, both Red (Power) and Green (ELCB)
indicators will light up if the Temperature Control Knob is in
‘ON’ position.
Pull the ELCB TEST LEVER down, Red (Power) and Green
(ELCB) Indicator should go off.
Pull the ELCB RESET LEVER down to reset the ELCB
, resume the power supply. (Fig 8)
If the Power Indicator does not go off when you pull
the ELCB Test lever, switch OFF the mains supply and
contact sales agent for repair service. Special skill is required
for repairing. NEVER try to repair the unit by yourself.
WARNING !
MIN. INLET WATER PRESSURE
MAX. INLET WATER PRESSURE
1.0 Bar (100kPa; 14.5 psi)
6.0 Bar (0.6 MPa ; 87.02 psi)

NOTE
12 www.electrolux.com
CONSUMER CARE
Indonesia
H
otline service: 08041119999
P
T. Electrolux Indonesia
E
lectrolux Building
J
l.Abdul Muis No.34, Petojo Selatan,
G
ambir Jakarta Pusat 10160
E
mail:[email protected]
S
MS & WA : 0812.8088.8863
M
alaysia
C
onsumer Care Center Tel: 1300-88-11-22
E
lectrolux Home Appliances Sdn. Bhd.
C
orporate Office Address: Unit T2-7, 7th Floor, Tower 2 ,
J
aya33 Hyperoffice, No. 3, Jalan Semangat, Seksyen 13,
4
6100 Petaling Jaya, Selangor
O
ffice Tel : [phone]
O
ffice Fax : [phone]
C
onsumer Care Center Address: Lot C6, No. 28,
J
alan 15/22, Taman Perindustrain Tiong Nam,
4
0200 Shah Alam, Selangor
C
onsumer Care Center Fax : [phone]
E
mail : malaysia.[email protected]
P
hilippines
C
onsumer Care Center Toll Free : 1-800-10-845-CARE 2273
C
onsumer Care Hotline : (+63 2) 845 CARE 2273
E
lectrolux Philippines, Inc.
1
0th Floor. W5th Avenue Building
5
th Avenue Corner 32nd Street
B
onifacio Global City,
T
aguig Philippines 1634
T
runkline: [phone]
W
ebsite : www.electrolux.com.ph
E
mail : [email protected]
S
ingapore
C
onsumer Care Center Tel: [phone]
E
lectrolux S.E.A. Pte Ltd.
1
Fusionopolis Place,
#
07-10 Galaxis, West Lobby
S
ingapore 138522.
O
ffice Fax : [phone]
E
mail : [e-mail]
T
hailand
C
onsumer Care Tel : [phone]
E
lectrolux Thailand Co., Ltd.
E
lectrolux Building 14th Floor
1
910 New Phetchaburi Road,
B
angkapi, Huai Khwang, Bangkok 10310
O
ffice Tel : [phone]
O
ffice Fax : [phone]
E
mail : [e-mail]
V
ietnam
C
onsumer Care Center Toll Free : 1800-58-88-99
T
el : ([phone]
E
lectrolux Vietnam Ltd.
F
loor 9th, A&B Tower
7
6 Le Lai street - Ben Thanh Ward - District 1
H
o Chi Minh City ，Vietnam
O
ffice Tel : [phone]
O
ffice Fax : [phone]
E
mail : [e-mail]
H
ongkong
T
el: ([phone]
D
ah Chong Hong, Ltd. - Service Centre
8
/F., Yee Lim Godown Block C
2-28 Kwai Lok Street, Kwai Chung, N.T.

NOTE
NOTE