Electrolux EYL85066WE User manual

EYL85066WE
EYL95066WE
EYL10566WE
WATER HEATER USER MANUAL

2 www.electrolux.com
WE’RE THINKING OF YOU
Thank you for purchasing an Electrolux appliance. You’ve chosen a product that brings with
it decades of professional experience and innovation. Ingenious and stylish, it has been
designed with you in mind. So whenever you use it, you can be safe in the knowledge that
you’ll get great results every time. Welcome to Electrolux.
Visit our website to:
Get usage advice, brochures, trouble shooter, service information:
www.electrolux.com
Register your product for better service:
www.electrolux.com/productregistration
Buy Accessories, Consumables and Original spare parts for your appliance:
www.electrolux.com/shop
2. SAFETY INSTRUCTIONS...................................................................................... 6
3. ELECTRICAL REQUIREMENTS............................................................................. 8
1. SAFETY INFORMATION........................................................................................ 4
4. WATER REQUIREMENTS....................................................................................10
5. INSTALLATION....................................................................................................11
6. OPERATION INSTRUCTION................................................................................18
7. MAINTENANCE ...................................................................................................21
8. HELPFUL HINTS AND TIPS.................................................................................22
9. TROUBLESHOOTING..........................................................................................23
CONTENTS

3ENGLISH
CUSTOMER CARE AND SERVICE
We recommend the use of original spare parts.
When contacting Electrolux Customer Service, ensure that you have the following data
available. The information can be found on the rating plate. Model, PNC, Serial Number.
Warning / Caution-Safety information.
General information and tips.
Environmental information.
Subject to change without notice.
GB IE
GREAT BRITAIN & IRELAND - Customer Care and Service
Standard Guarantee Conditions and Exclusions.To see our guarantee conditions and
exclusions please visit www.electrolux.co.uk or contact our Customer Care Department.
Service & Spare Parts. Please contact your local Service Force Centre on; 08445 616616
(Your call will automatically be routed to your local centre) For the address of your local
centre please visit; www.electrolux.co.uk Please ensure you read the information under
‘What to do if’ in your instruction booklet before contacting us for service.
Servicing and/ or installation of your product, including electrical connections and water
connections should be carried out by a suitably qualied engineer. In the user manual and
on our web site, www.electrolux.co.uk you will nd some useful information on how to
deal with minor faults and how to take care of your product. When contacting us for
Service please ensure that you have your purchase receipt and the following information
available:
Model No............................................... Serial No..................................................
Product No............................................ Purchase Date:.........................................
Republic of Ireland: For Customer Care or Service please contact us at the following
address, Electrolux Group(Ir) Ltd, Long Mile Rd, Dublin 12, Republic of Ireland.
Tel No. [phone], E mail; [email protected]
Electrolux : 08445 613613
Customer Care. Please contact Electrolux Major Appliances, Addington Way, Luton,
Bedfordshire, LU4 9QQ.

Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible if an incorrect installation and use causes
injuries and damages. Always keep the instructions with
the appliance for future reference.
Risk of suffocation, injury or permanent disability.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved.
1. SAFETY INFORMATION
1.1 Children and vulnerable people safety
1.2 General Safety
Keep all packaging away from children.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Before maintenance swich off the appliance.
Do not switch on if there is a possibility that the water in
the heater is frozen.
The spray head must be descaled regularly.
The outlet must not be connected to any tap or tting
other than those specied.
WARNING!
4 www.electrolux.com

The appliance must be earthed.
Do not install the appliance in locations where freezing
can occur.
The means for disconnection must be incorporated in
the xed wiring in accordance with the wiring rules.
The xed wiring insulation must be protected, for
example, by insulating sleeving having an appropriate
temperature rating.
The pressure relief device must be tted during
installation, unless it is incorporated in the appliance.
The appliance must be permanently connected to xed
wiring.
5ENGLISH

Remove all the packaging.
Do not install or use a damaged appliance.
All products manufactured and supplied by
Electrolux are safe provided they are
installed, used correctly and receive regular
maintenance in accordance with these
instructions.
Only a qualied person must install
this appliance.
2.1 Installation
2.2 Use
WARNING!
2. SAFETY INSTRUCTIONS
Risk of re and electrical shock.
WARNING!
Make sure that a shock protection is
installed.
Use the strain relief clamp on cable.
Make sure not to cause damage to the
mains plug (if applicable) or to the mains
cable. Contact the Service or an electrician
to change a damaged mains cable.
All electrical connections must be made by
a qualied electrician.
The appliance must be earthed.
Before carrying out any operation make
sure that the appliance is disconnected
from the power supply.
Use the correct electricity mains cable.
Do not let the electricity mains cable tangle.
Make sure the appliance is installed
correctly. Loose and incorrect electricity
mains cable or plug (if applicable) can
make the terminal become too hot.
The electrical installation must have an
isolation device which lets you disconnect
the appliance from the mains at all poles.
The isolation device must have a contact
opening width of minimum 3 mm.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
Always switch off the power at the
consumer unit and isolate the electrical
supply before making any electrical
connections or if you have to remove the
cover of an installed unit.
Remove all the packaging, labeling and
protective lm (if applicable) before rst use.
Obey the installation instruction supplied
with the appliance.
Keep the minimum distance from the other
appliances and units.
If you are in any doubt about your ability to
install this product safely you must employ
the services of an experienced qualied
plumber/electrically qualied person.
Do not operate the shower unit if you
suspect the water inside is frozen. Do not
site the shower unit where it might be
subjected to freezing conditions.
Do not install this shower unit in a
room/environment without adequate
ventilation or an extractor tted. This is
required to prevent condensation forming
within the unit.
The unit must be mounted on the nished
wall surface (usually tiled). Under no
circumstances must you tile up to or seal
around the unit as this may prevent air
circulating and condensation escaping.
This shower unit must not be modied* in
any way as this will invalidate the guarantee.
* Except for those indicated on this manual
where the product has been designed to
be modied by the installer.
You must not t a “water saving” handset
(whereby the ow of water can be
restricted or turned off) to the shower,
otherwise this can result in scalding and/or
unit failure.
Electrical connection
Risk of re and electrical shock.
WARNING!
6 www.electrolux.com

Do not change the specication of this
appliance.
Do not operate the shower unit if the
showerhead or spray hose has been
damaged or is blocked.
2.3 Disposal
Do not block the ow of water from the
showerhead, by placing it (smothering it)
on your hand or any other part of your
body or foreign object.
Do not operate the shower if the water
stops owing during use or if the water is
leaking from the shower unit itself.
Turn off at the mains electrical supply and
refer to the Troubleshooting section (see
page 23) or contact Electrolux Customer
Services (see page 3).
Do not crush or kink the shower hose, this
could damage the hose, cause leaks and
activate the pressure relief device.
Contact your municipal authority for
information on how to discard the
appliance correctly.
Disconnect the appliance from the mains
supply.
Cut off the mains cable and discard it.
2. SAFETY INSTRUCTIONS
Risk of injury or suffocation.
WARNING!
7ENGLISH

Temperature
8 www.electrolux.com
3. Electrical Requirements
Mains electrical
supply
Shower unit
30mA RCD for
ampage of
MCB/Fuse see
circuit protection
table on page 5
For cable capacity see
cable current carrying
capacity table on page 5
This appliance MUST be earthed!
Unit power table
The installation, supply cable and circuit
protection must conform with BS 7671 (IEE
amperage required.
Important: Before making any sort of
electrical connection within the installation
make sure that no terminal is live. If in any
doubt, switch off the whole installation at the
mains supply and remove the correct fuse.
The shower must only be connected to a
230-240V ac supply. If you are installing a
shower with a kilowatt rating above 9kW, it is
advisable to contact the local electricity
supply company.
The shower must be connected to its own
independent electrical supply. It must not be
connected to a ring main, spur, power
socket, or lighting circuit.
The electrical supply must be adequate for
the loading of the unit and existing circuits.
Check your consumer unit (main fuse box)
has a main switch rating of 80A or above and
that it has a spare fuse way which will take
the fuse or Miniature Circuit Breaker (MCB)
necessary for the shower
If your consumer unit has a rating below 80A
or if there is no spare fuse way, then the
installation will not be straightforward and
may require a new consumer unit serving the
house or just the shower. In this case, you
will need to contact the local electricity
company. They will check the supply and
carry out what is necessary.
WARNING!
Rating at 240V Rating at 230V
8.5kW 7.8kW
9.5kW 8.7kW
10.5kW 9.5kW
Consumer unit
Double pole switch

9ENGLISH
3. Electrical Requirements
The current rating will be reduced if the
cabling is bunched with others, surrounded
by thermal loft or wall insulation or placed in
areas where the ambient temperature is
above 30°C. Under these conditions, derating
factors apply and it is necessary to select a
larger cable size.
In the majority of installations, the cable will
unavoidably be placed in one or more of the
above conditions. If so, it is strongly
recommended to use a minimum of 10mm
cabling throughout the shower installation.
In any event, it is essential that individual site
conditions are assessed by a competent
electrician in order to determine the correct
cable size and permissible circuit length.
Circuit Protection table.
Where shower cubicles are located in any
rooms other than bathrooms, all socket
outlets in those rooms must be protected by
a 30mA RCD.
The current carrying capacity of the cable
must be at least that of the shower circuit
protection (see Cable current carrying
capacity table).
To obtain full advantage of the power
provided by the shower, use the shortest
cable route possible from the consumer unit
to the shower.
The shower circuit should be separated from
other circuits by at least twice the diameter of
the cable or conduit.
Unit Rating
(240V)
Circuit Protection Device
MCB Cartridge Fuse
8.5kW
9.5kW
10.5kW
40A 45A
40/45A 45A
45A 45A
Cable current carrying capacity table (for twin and earth PVC insulated cable)
Current carrying capacity
In an insulated wall In conduit or trunking Clipped direct or buried
in a non insulated wall
6mm² 32A 6mm² 38A 6mm² 46A
10mm² 43A 10mm² 52A 10mm² 63A
Note: Cable selection is dependant on derating factors
For close circuit protection DO NOT use a
rewireable fuse. Instead use a suitably rated
Miniature Circuit Breaker (MCB) or cartridge
fuse (see Circuit protection table).
A 30mA residual current device (RCD) must
be installed in all UK electric and pumped
shower circuits. This may be part of the
consumer unit or a separate unit.
A 45 amp double pole isolating switch with a
minimum contact gap of 3 mm in both poles
must be incorporated in the circuit.
It must have a mechanical indicator showing
when the switch is in the OFF position, and
the wiring must be connected to the switch
without the use of a plug or socket outlet.
The switch must be accessible and clearly
identiable, but out of reach of a person
using a xed bath or shower, except for the
cord of a cord operated switch, and should
be placed so that it is not possible to touch
the switch body while standing in a bath or
shower cubicle. It should be readily
accessible to switch off after using the
shower.

Temperature
10 www.electrolux.com
Isolating stop valve
Mains water
supply Shower unit
Bath spillover
level
Hose retainer
Minimum 25mm
between showerhead
and spillover
1m minimum
height from
shower unit to
floor
4. Water Requirements
This shower needs to be installed in
accordance with the following Installation
Requirements and Notes (IRN) to ensure
they meet the requirements of the Water
Supply (Water Fittings) Regulations 1999
and the Scottish Byelaws 2004.
If the riser kit is supplied with a ‘soapdish
hose retainer’ or bespoke ‘hose retainer’, it
will in most cases meet this requirement. If
the showerhead can still be placed within a
bath, basin or shower tray within the 25mm
limit, then a double check valve, or similar,
It is required that the showerhead be
so that it can only discharge water at a point
not less than 25mm above the spill-over level
of the relevant bath, shower tray or other
If the shower is to be installed in a hard water
area, we recommend that an in-line scale
the shower. Please refer to your supplier for
advice.
The shower must be connected to a mains
water supply only with a minimum working
inlet pressure of 0.07MPa (0.7bar) at a
maximum static inlet pressure must not
exceed 1.0MPa (10bar).
If it is intended to operate the shower at
pressures above the maximum stated, a
suitable pressure reducing device (PRD)
should be used.
Do not operate the shower unit if
you suspect the water inside is
frozen. The shower must not be
installed in an area subject to
freezing conditions.
WARNING!