Elenco Electronics TEACH TECH King Lizard TTR-892 Installation guide

From the Makers of
TTR-892 10 +
ASSEMBLY & INSTRUCTION MANUAL
All manuals and user guides at all-guides.com
all-guides.com

1
I ntroduction
Mechanical Parts L ist
H ead Module Assembly
H ead Module T esting
B ody Module T esting
S tickers
P.2
T ools Y ou May N eed P.2
P.2
Plastic Parts P.4
P.5
P.8
P.19
B ody Module Assembly P.17
P.34
H ow to Play P.35
Escape Mode
F ollow- me Mode P.36
P.37
W arning P.38
T rouble S hooting P.39
C o n t e n t s
All manuals and user guides at all-guides.com

1 : 1 1 : 1 1 : 1
Introduction
Mechanical Parts List
Gear With Shaft
Pinion Gear (White)
Tapping Screw
Gear (Red)
Gear (Purple)
Hex Shaft (Middle) Hex Shaft (Long)Hex Shaft (Short)
Gear (White)Gear (Yellow)
QTY
1
511
111
QTY
1
QTY
1
QTY
QTY QTY QTY
QTY QTY QTY
2
P4P3P2P1
P5 P6 P7
P8 P9
P10
King Lizard is modeled after Australian Frilled Lizards. When these lizards are surprised or
threatened they exhibit a pretty spectacular display. First it's the wide open, hissing mouth with
sharp little canine teeth. Then comes the big reveal, the neck frills jump from limp to frightening
in a snap. This aggressive behavior is truly a bluff and if you don't run away, the lizard will.
The King Lizard functions with two modes, "Follow-me" and "Escape". With the 2 mode switch,
when the infrared (IR) sensor is activated in the Elude mode, the King Lizard will act startled.
The frill will deploy, jaws gape and LED eyes blaze all before scurrying away to a safe
distance. When the IR sensor is activated in the Follow-me mode, your King Lizard will bluff
the threat (you) with an energetic frill display. If your King Lizard does not sense danger it will
follow you like a pet.
2
Alkaline batteries are
recommended
Tools You May Need
Diagonal Cutter Knife
Battery (AAA) x 4 Screwdriver Hammer Safety Glasses
Important: If any parts are missing or damage, DO NOT RETURN TO THE
RETAILER. E-mail us at [email protected]om or call [phone]
•
•Product contains functional edges and sharp points.
All manuals and user guides at all-guides.com

(Spare part : 1 pc)
Sticker
Round Shaft Round Shaft PC Board
112
QTY QTY QTY
P13P11 P12
Motor With Connector Motor With Connector
Battery Holder With Connector
11
QTY QTY
P15P14
Black
W / Short Wires
Black
Red Red
PC Board With Connector
11
QTY QTY
P17P16
Frill
Spare Parts
1
1
QTY QTY
P18
1
QTY
P20
Adhesive Tape
P19
W / Long Wires
3
DC 6V
All manuals and user guides at all-guides.com

Cut the plastic parts when they are required.
Do not cut them in advance.
2
2 1
E
5
4
32
6
7
89
1B
10
11
12
9
12
16
17
181920212223
24
25
15
14 10
11
13
8
3
45 2
1
C
L
67
C3
C4
R
1
6
7
8
9
A8
A11
A1
A2
2
3
5
12
13
11
10
10
9
4
A
1
2
34
D
012
Plastic Parts
burr burr
burr
Tip:cut off the burrs before assembly
Spare Parts
Spare Part
4
All manuals and user guides at all-guides.com

H e a d M o d u l e A s s e m b l y
5
1
C9
2
C6
C15
C5
All manuals and user guides at all-guides.com
all-guides.com

S ide V iew
P2 ( R ed)
P8
( S hort)
C13
P1
P14
B 3
R edB lack
6
3 4
5
1
1
1
2
2
1: 1
W / Short Wires
All manuals and user guides at all-guides.com

Make sure “ “ is positioned as shown below.
It is to assist you in assembling C8 correctly.
7
6
7
8
1
2
2
C8
B4x6
Black
Red
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

9
9
10
P19
A13
P18
A7
A9 A9
A10A10
Cut the frill as illustrated below.
Make sure adhesive tapes come with thin glued films while tearing off.
*Extra frill included
All manuals and user guides at all-guides.com