elero Lumero-868 User manual

Operating instructions (translation)
181008706_EN_0216
LED (transmit)
DOWN button
( )
General information
The Lumero-868 is a wireless sun sensor for your shade
system (roller shutters, awnings, ventetian blinds).
Integrated solar cells enable autonomous function of the
device. Radio signals (fequency 868 MHz) are transmitted
between the Lumero-868 and the receiver.
Important!
The Lumero-868 only operates in combination with radio
receivers from the elero ProLine and ProLine 2 radio-
system.
Manual operation oft the system is carried out with a
manual/wall transmitter. This item ist not included in the
scope of delivery.
Recommendation:
Use a LumeroTel or VarioTelPlus hand-held transmitter to
deactivate the sun function.
Warning!
Important safety instructions!
Observe the following instructions: .
• Only use unmodified original elero electrical
parts.
• Keep persons away from the operating range
of the system.
• Keep children away from the controls.
• Follow the relevant country-specific regulati-
ons.
• If one ofr more devices are used for control-
ling the system, the operating range mus stay
visible during operation.
• The device contains swallowable small parts.
Safety instructions
Intended use
The Lumero-868 may only be used for controlling roller
shuttter, awning and blind systems.
Third-party devices should only be connected after con-
sultation with your specialised dealer.
• Please ensure that the radio installations are not ope-
rated in areas of heightened possible interference (e.g.
hospitals, airports ...).
• The remote control is only approved for devices and
systems for which any malfunction of the manual trans-
mitter or receiver would not result in a risk for persons,
animals or properly, or if such a risk is covered by
other safety devices.
• The operator has no protection whatsoever from inter-
ferences by other radio emitters and local terminals
(e.g. also from radio installations), that are normally
used on the same frequency range.
• Only use radio receivers with equipment and units
approved by the manufacturer. .
Device function
The light intensity is measured at intervals and compared
with the set values.
Brightness above
set value (delay time
approx. 5 - 7 min.)
→ Awning moves out, roller shutter,
venetian blind moves down
(flashing LED).
Brightness below
set value (delay time
approx. 15 - 17 min.)
→Awning moves in or remains in,
roller shutter, venetian blind moves
up.
The sliding switch at the programmed manual transmitter
can be used to switch the light function of the Luemr-868
on or off.
Technical data
Power supply Solar
Temperature range –25 °C bis +60 °C
Detection angle 190 °
Protection class IP 54
Radio frequency
for USA and some countries from south
america, Canada, Australia
868 MHz
915 MHz
Standby approx. 1 hour
Multiple contact
switch
STOP /
P button
UP button
( )
Lumero-868
28 680 0006
٭

2 | EN
Charging the Lumero-868
The Lumero-868 is delivered in the discharged condition.
Place the Lumero-868 under a lamp for at least 30
minutes or push the DOWN-button on the Lumero-868 for
at least 3 minutes before starting up.
Note: The travel keys have two levels.
The first level transfers energy from a built-in battery to
the energy store.
The second level activates the travel command.
Programming Lumero-868
Condition
The end positions of the awning, the roller shutter or the
venetian blind have been set, a transmitter has been pro-
grammed, and the Lumero-868 has been loaded (LED
lights and/or flashes wehn a button ist pressed).
For bidirectional use, the device version of the installed
radio receiver is relevant:
elero Combio form version 75 onwards
elero RevoLine from version 21 onwards or
elero radio receiver from manufacturing date May 2012.
1. Move the blind to an intermediate position.
2. Press and hold the UP, DOWN and Pbuttons on
the programmed hand-held transmitter for at least 3
seconds.
If the blind not travels UP and DOWN, continue at 4.
If the blind does not travel UP and DOWN, continue
at 3.
3. Press an hold the STOP/P button on the Lumero-868
for 3 seconds until the transmission LED begins flas-
hing ornage rapidly. The blind now moves UP and
DOWN for 2 minutes. The transmission LED will flash
ornage rapidly every time a button is pressed if the sys-
tem is in programming mode.
4. Press the UP button on the unit immediatedly after the
start of an up movement (retract) begins.
The drive will stop briefly.
5. Press the DOWN button on the unit immediately after
the start of an down movement (extend) begins.
The drive will stop briefly.
The Lumero-868 ist now programmed.
Possible modes of operation
The Lumero-868 can be operated in four different modes.
The operating mode is indicated by the flashing signal:
1. Awning mode
(1 x flashing of the transmission LED)
2. Visual protection mode
(2 x flashing of the transmission LED)
3. Roller shutter mode
(3 x flashing of the transmission LED)
4. Test mode (checking the light function)
The current mode of the Lumero-868 is displayed by
means of the flashing of the LED.
The awning mode is set as standard in the delivery con-
dition.
In the case of OEM versions, a different mode can also be
set.
Awning mode
The awning is automatically retracted whend the current
measured sun value changes form 1 to 0 (late evening) or
when the current measured light value changes from 0 to
1 (early morning).
Visual protection mode
(protection against prying eyes)
To keep the blind closed even in the evening, close the
blind manually using your hand-held transmitter or a
timer.
The current transitions of the measured light values from
1 to 0 (late in the evening) of from 0 to 1 (early in the
morning) will be ignored.
The blind will remain closed throughout gthe night.
The switching commands such as tilting position (venetian
blind) or ventilation position (roller shutter) will be executed
automatically the next day.
Roller shutter mode
If the roller shutter is driven manually or by a timer of the
lower end position, the light function (driving according to
set light value) will be switched off.
The current transitions of the measured light values from
1 to 0 (late in the evening) of from 0 to 1 (early in the mor-
ning) will bie ignored.
Test mode (checking the light function)
Condition:
The blind is retracted.
The delay times are shortened in the test mode (from
minutes to seconds). You can then test the travel move-
ment of your system when the light threshold is exceeded.
Warning!
Risk of injury by the upward and downward tra-
vel of the awning/venetian blind.
The test mode is active for 5 minutes. This time can-
not be sortened.
Keep away from the operating range of the system.
1.Press the UP button for at least 3 seconds until the
transmission LED flashes.
The test mode stays active for 5 minutes but the LED
goes out.
2.Shine a torch (not a LED lamp) on the light sensor.
Specified light threshold value is exceeded.
➙blind extends/lowers after 5 seconds.
Light value falls below the specified threshold.
➙upward travel of the awning/blind after 15 seconds.
You can repeat the operation as often as you want within
5 minutes.
©elero GmbH

EN | 3
Setting the threshold values
Insight the Lumero-868 you will find a multi-way switch for
setting the threshold value for light; this can be adjusted
using a small screwdriver.
Setting the threshold values at the Lumero-868
Step 0 light function is switched o󰀨 /
change over the mode
Step 1 extend in low light level
minimum responsivity
Steps
2 - 9 and
A - E
13 Steps
Step 7 factory setting
(intermediate levels)
Step F extend at a high level
maximum responsivity
Deleting the programmed Lumero-868
Press the - and the -button simultaneously.
The LED goes out. Wait until the LED lights up again after
approx. 3 seconds.
The lumero-868 is deleted.
Change the mode
There is a multiple contact switch inside the Lumero-868.
1. Use a small screwdriver to set the multi-way switch to 0.
2. Press and hold the UP and DOWN buttons for at least 3
seconds. Pressing the two buttons again switches to the
next mode.
The current mode of the Lumero-868 is indicated by the
transmit LED flashing:
Transmission LED flashes 1x →awning mode
Transmission LED flashes 2x →visual protection mode
Tansmission LED flashes 3x →roller shutter mode
The mode set is indicated at each radio transmission by
the flashing of the transmission LED (LED flashing pattern
every 3 minutes).
Set the multi-way switch back from 0 to a light value of your
choice.
Installation
Check whether a perfect radio connection exists between
the Lumero-868 and the receiver before installation at the
desired installation position.
Hinweis
Fix the Lumero-868 with the screws provided.
149,7
42
14,5
4,5
4,5
14,5
118,5
28
1,7
149,7
28
1,7
Vertical installation
position
Horizontal installation
position
Sensor-
surface
Sensor-
surface
Maintenance
The Lumero-868 is maintenance-free, but the cover must
be cleaned from time to time. Otherweise, light entry is limi-
ted and shortens functioning time.
Troubleshooting
Fault Cause Remedy
• Awning does
not move
out in sunny
conditions
• Threshold set
incorrectly
• Manual mode is set
• Poor radio connection
• Light sensor is dirty
• Sun threshold (level 0)
• Set correct value
• Set automatic mode
• Change the position of
the Lumero-868
• Clean light sensor
• Set appropriate level
x
©elero GmbH

EN
EC-DECLARATION OF CONFORMITY
We hereby declare that the following mentioned product/s meet/s the standards of the European Community.
Product designation:
ProLine 2
•Lumo-868 all versions
•Lumero-868 / -915 all versions
•Aero-868 / -915, Aero-868 / -915 Plus, Aero-868 / -915 AC all versions
•Sensero-868 / -915 AC, Sensero-868 / -915 AC Plus all versions
Description: Sun, dusk, wind and rain sensors with bidirectional and unidirectional
radio-based sensor system.
Can be used in conjunction with controllers for opening and closing roller shutter and
other shading systems as well as other actuators.
The conformity of the above mentioned products with the relevant health and safety requirements is taken into
account by the following directives and standards:
•EMC Directive 2004/108/EC
EN 61000-6-2:2005, EN 61000-6-3:2001
EN 60730-1:2000, EN 60730-2-7:1991
•Low Voltage Directive 2006/95/EC
EN 60335-1:2002
•R&TTE Directives 1999/5/EC
ETSI EN 301 489-3 V1.4.1
ETSI EN 300 220-2 V2.1.2
•RoHS Directive 2002/95/EC
Beuren, 05.07.2012
Ralph Trost
-CE Manager-, -Representative documentation -
EG-Konformitätserklärung
elero GmbH
Antriebstechnik
Maybachstr. 30
73278 Schlierbach
Fon: [phone]
Fax: [phone]
[email protected]
www.elero.com We reserve the right to make technical changes