elero PatioControl User manual

PaoControl
Pergola-Steuerung / Pergola Control Unit / Commande de pergola /
Unità di controllo pergola / Mando de pérgola
Montageanleitung
Bitte bewahren Sie die Montageanleitung auf!
Operating instructions
Please take care of the operating instructions!
Instructions de montage
Veuillez conserver les présentes instructions de montage!
Istruzioni per l‘uso
La preghiamo di conservare le istrzioni per l‘uso!
Instrucciones de montaje
Por favor, conserve estas instrucciones de montaje!
[TN: 2011781]
DE
EN
FR
IT
ES

Originalmontageanleitung
Änderungen vorbehalten. Alle Rechte für den Fall der Patent-, Gebrauchsmuster- oder
Geschmacksmustereintragung vorbehalten.
Translation from the original German version
Subject to change without notice. All rights reserved in the event of registration of patents,
working models or design patents.
Traduction à partir des instructions de montage d‘origine en langue allemande
Sous réserve de modifications. Tous droits réservés pour l‘enregistrement de brevet, de modèle
d‘utilité ou de modèle déposé.
Traduzione dalla versione originale in lingua tedesca
Con riserva di modifica. Tutti i diritti riservati per la registrazione di marchi registrati, disegni o
modelli di utilità.
Traducción del original alemán
Reservado el derecho a realizar modificaciones. Reservados todos los derechos de registro de
patentes, modelos de utilidad o modelos o diseños industriales.
FR
DE
ES
IT
EN

EN
Tables of contents
1General............................................................................................................................................................................................... 3
1.1 Notes on the installation instructions ........................................................................................................................................ 3
1.2 Standards and guidelines.............................................................................................................................................................. 3
1.3 Use in line with intended use ....................................................................................................................................................... 3
1.4 Foreseeable misuse........................................................................................................................................................................ 4
1.5 Guarantee and liability ................................................................................................................................................................... 4
1.6 Customer service of the manufacturer...................................................................................................................................... 5
2 Safety .................................................................................................................................................................................................. 6
2.1 General safety notices.................................................................................................................................................................... 6
2.2 Formulation of safety information............................................................................................................................................... 6
2.3 Safety principles............................................................................................................................................................................... 7
2.4 General duties of the plant operator ......................................................................................................................................... 8
2.5 Personnel requirements................................................................................................................................................................ 8
2.6 Safety information on the technical condition......................................................................................................................... 9
2.7 Safety information on transport, assembly and installation................................................................................................. 9
2.8 Safety information on operation.................................................................................................................................................. 9
2.9 Safety information on the electrical installation ...................................................................................................................... 9
3 Structure/description ...................................................................................................................................................................11
3.1 Technical data.................................................................................................................................................................................11
3.2 Items supplied................................................................................................................................................................................13
3.3 Connection of the control unit...................................................................................................................................................14
3.4 Building electrical connection.....................................................................................................................................................16
3.5 Icons and explanation of terms .................................................................................................................................................16

4 Teach-in hand-held transmitter.................................................................................................................................................17
4.1 Functions of the switches and LEDs .........................................................................................................................................19
4.2 Delete the current radio channel in the control unit ...........................................................................................................22
4.3 Deleting all radio channels in the control unit .......................................................................................................................22
5 Teach-in of the limit positions of the actuators .....................................................................................................................24
5.1 Current values................................................................................................................................................................................25
5.2 Operation ........................................................................................................................................................................................26
6 Teach-in Sensero/Sensero plus weather sensor...................................................................................................................27
6.1 Functions of the pergola with the Sensero/Sensero plus weather sensor.....................................................................30
6.2 Threshold values of the sensors................................................................................................................................................31
6.3 Delay times......................................................................................................................................................................................32
6.4 Faults.................................................................................................................................................................................................32
7 Light module...................................................................................................................................................................................33
7.1 Installation.......................................................................................................................................................................................33
7.2 Overview ..........................................................................................................................................................................................34
7.3 Teach-in hand-held transmitter for the light module...........................................................................................................35
8 Fault rectification ...........................................................................................................................................................................37
9 Declaration of Incorporation ......................................................................................................................................................40
10 Waste disposal ...............................................................................................................................................................................41
11 Annex .......................................................................................................................................................................... 42

General 3
PatioControl
EN
1 General
1.1 Notes on the installation instructions
The contents are classified by the service life phases of the PatioControl control unit.
The manufacturer reserves the right to make changes to the technical specifications stated in these installation
instructions. In detail these can differ from the respective version of the device without the factual information being
fundamentally changed and without losing their validity. The current status of the technical specifications can be
requested from the manufacturer at any time. Claims may not be asserted in this respect. Deviations from the text
and pictorial statements are possible and are dependent on the technical development, equipment and accessories
of the device. The manufacturer shall provide information on any differing details relating to special versions by means
of the sales documentation. Other specifications shall remain unaffected by this.
1.2 Standards and guidelines
The basic health and safety requirements of the applicable laws, standards and guidelines were applied during the
design phase.
The safety of the device is confirmed by the Declaration of Incorporation (see chapter “Declaration of Incorporation”).
All information relating to safety in these installation instructions refers to the laws and regulations that are currently
valid in Germany. All information in these installation instructions must be complied with at all times and without
limitation. In addition to the safety information in these installation instructions, the regulations applicable at the place
of installation with regard to accident prevention, environmental protection and occupational safety must be observed
and adhered to. The guidelines and standards for safety assessment can be found in the Declaration of Incorporation.
1.3 Use in line with intended use
The device is intended for control of actuators for opening and closing pergolas. One or two actuators can be
connected to the device.
The operator alone is liable for any damage arising from the non-intended use of the device. The manufacturer

4
assumes no liability for personal injury or damage to property caused by misuse or procedural errors, improper
operator control or improper start of operation.
Safe and fault-free operation and reliability of the devices can be guaranteed only when it is used as intended.
Proper use also includes compliance with and observance of all safety instructions contained in this manual.
1.4 Foreseeable misuse
Installation different from the intended purpose approved by the manufacturer is considered foreseeable misuse.
1.5 Guarantee and liability
In principle, the General Terms & Conditions of Sale and Delivery of the manufacturer apply. The Terms & Conditions
of Sale and Delivery are part of the sales documentation and are given to the operator at the time of delivery. Liability
claims for personal injury and damage to property are excluded if they can be attributed to one or more of the
following causes:
• Use not in compliance with the intended use of the device.
• Improper installation or operation of the device.
• Structural modifications to the device without the written approval of the manufacturer.
• Operation of the device with improperly installed connections and defective or improperly attached safety and
protection devices.
• Non-compliance with the safety regulations and information provided in these instructions.
• Exceeding the limits of the technical specifications.

General 5
PatioControl
EN
1.6 Customer service of the manufacturer
The device may be repaired only by the manufacturer in the event of a fault. The address for sending the device to the
customer service department can be found on the inside of the back cover.
If you have not purchased the device directly from elero, please contact the manufacturer of the machine or the
supplier of the device.

6
2 Safety
2.1 General safety notices
These instructions contain all safety instructions that must be observed to avoid and prevent dangers in working with
the PatioControl control unit. Safe use of the device is guaranteed when all the specified safety notices and directions
are complied with.
2.2 Formulation of safety information
The safety notices in this document are marked with safety symbols and formulated in accordance with the SAFE
principle. They contain specifications relating to the type and source of danger, the possible consequences, as well as
the prevention of the danger.
DANGER
Warns of an accident that will occur if the instructions are not followed. The
accident will lead to severe, possibly life-endangering injury or death.
WARNING
Warns of an accident that may occur if the instructions are not followed. The
accident may lead to severe, possibly life-endangering injury or death.
CAUTION
Warns of an accident that may occur if the instructions are not followed. The
accident may lead to moderate injury, for example burns, injury to the skin or
crushing.
WARNING
Warns of the possibility of material damage.

Safety 7
PatioControl
EN
NOTE
Important general notice.
DANGER DUE TO AN ELECTRICAL VOLTAGE, ELECTRIC SHOCK
This symbol refers to dangers associated with electrical currents.
2.3 Safety principles
The device has been built using state-of-the-art technology in accordance with generally accepted rules of safety
and is safe to operate. The basic safety and health requirements of the applicable laws, standards, directives
and guidelines have been applied in the construction of the device. The safety of the device is confirmed by the
Declaration of Incorporation.
All specifications pertaining to safety relate to the currently valid regulations of the European Union. In other
countries, the operator must ensure that the relevant laws and national regulations are adhered to.
In addition to the safety instructions in this manual, general accident prevention and environmental protection
regulations must also be complied with.
The device must only be used in a technically perfect condition, for its intended use and in a safety and risk-conscious
manner. The device is designed for use as described in the “Intended use” section. In the event of use that is not in
compliance with the intended use, injury to the life and limb of the user or third parties or impairments to the device
and other property can arise. Any accidents or almost accidents during the use of the device that lead to or could
have led to personal injuries and/or damage in the working environment must be reported directly and without delay
to the manufacturer.
All safety information specified in the instructions and on the device must be observed. In addition to this safety
information, the operator must ensure that all national and international regulations applicable in the respective
country of use, as well as other binding regulations relating to operational safety, accident prevention and
environmental protection, are complied with. All work on the device must be performed only by trained and
authorised personnel who have been instructed on safety.

8
2.4 General duties of the plant operator
• The operator is obligated to use the device only when it is in perfect working order and is safe to operate. The
operator must ensure that, in addition to the safety information in the instructions, the generally accepted
safety and accident-prevention regulations, the specifications of DIN VDE 0100 and the provisions relating to
environmental protection of the respective country of use are observed and complied with.
• The operator is responsible for ensuring that all work with device is carried out only by appropriately trained and
authorised personnel who have been instructed on safety.
• Ultimately responsible for accident-free operation is the plant operator of the device or the personnel authorized by
the plant operator.
• The operator is responsible for adhering to the technical specifications.
2.5 Personnel requirements
• Any person commissioned with performing work on the device must have read through and understood the
instructions completely before performing the corresponding work. This also applies if the person concerned has
previously worked with such a device or has been trained to do so.
• All work on the device must be performed only by trained and authorized personnel who have received safety
instruction. Before starting any operations, personnel must be made aware of the dangers involved in handling the
device.
• All persons may only carry out work commensurate with their qualifications. The area of responsibility of the various
persons must be clearly defined.
• Any personnel commissioned with working on the device must have no physical limitations that could temporarily or
permanently impair their attentiveness or judgement (e.g. due to excessive fatigue).
• Minors or persons under the influence of alcohol, drugs or medication are prohibited from working with the device
and performing any installation, dismantling or cleaning work.

Safety 9
PatioControl
EN
2.6 Safety information on the technical condition
• The device must be checked for damage and correct operation before installation.
• The operator is obligated to operate the device only when it is in perfect working order and is safe to operate. The
technical condition must comply with the legal requirements at all times.
• If dangers to personnel or changes in operating behaviour are identified, the device must be shut down immediately
and the incident reported to superiors or the operator.
• Modifications and attachments to or conversions of the device are not permitted without the authorisation of the
manufacturer.
2.7 Safety information on transport, assembly and installation
The relevant transport company is fundamentally responsible for the transport of the device. The following safety
requirements must be complied with during transport, erection and installation of the device:
Assembly and installation work must only be carried out by trained and qualified personnel.
2.8 Safety information on operation
The operator of the device is obligated to ensure the safe and proper state of the device before the initial start of
operation.
This is also necessary during operation of the device at regular intervals to be determined by the plant operator.
2.9 Safety information on the electrical installation
• All work on the electrical system must be performed only by authorized skilled electricians in accordance with
the applicable rules and stipulations of the trade association, in particular the stipulations of DIN VDE 0100.
Furthermore, the national statutory regulations of the respective country of application must be observed.
• In the event of any defects, such as loose connections or defective or damaged cables, the device must not be put
into operation.
• In the event of faults with the electrical equipment, the device must be switched offimmediately.
• The device must be de-energised before any inspection, installation or dismantling work.

10
• The device must not be hosed down with a high-pressure cleaner or steam jet.
The following must be checked before connecting the device to the power supply:
• Are all electrical connections, safety devices, fuses, etc. properly installed, connected and earthed?
• Is the power connection provided in accordance with the information in the electrical wiring diagram (voltage type,
voltage level)?
• Has the supply line been de-energised?

Structure/description 11
PatioControl
EN
3 Structure/description
3.1 Technical data
Technical data of control unit and power supply
Minimum Nominal Maximum
Building power feed 3 x 1.5 mm²
Power supply
Connection voltage 205 V 230/240 V - 1 AC 264 V
Recommended back-
up fuse
2 A 6 A
Power consumption 2.2 A
Control unit Rated voltage 22 V DC 24 V DC 26 V DC
Power consumption 10 A
Cut-offcurrent of actuator for the closing force 0.2 A in 10 stages 2.0 A
Operating temperature range -20 °C 20 °C 50 °C
Degree of protection of control unit and power
supply
Degree of protection IP 65 - as per VDE 0470/DIN 40050/EN 60529
Installation position user-defined
Housing dimensions 190 x 75 x 75 mm
(without screw fastenings)
Colour silver-grey

12
Technical data of control unit and power supply
Radio frequency 868 MHz / 915 MHz
Minimum Nominal Maximum
Radio system elero bidirectional
Number of usable transmitters 16
Actuators
Number 1 2
Rated voltage 24 V DC
Performance 50 W
Limit switch Limit switches or closing force
Runtime 3 min
Light module
Type of lighting LED (common positive pin)
Number of light
channels
14
Rated voltage 22 V DC 24 V DC 26 V DC
Power per light
channel
50 W
Total power of light 150 W
Tab. 1: Technical data of control unit and power supply

Structure/description 13
PatioControl
EN
3.2 Items supplied
• PatioControl control unit
• Power supply 230 V/AC / 24 V/DC 150 W or 240 W
• Variotel2, Tempotel2 or Multitel2 hand-held transmitter
• Temperature sensor (optional)
• optional Sensero 868 AC or Sensero 868 AC Plus weather sensor
• Assembly Manual

14
3.3 Connection of the control unit
DANGER DUE TO AN ELECTRICAL VOLTAGE, ELECTRIC SHOCK
Electrical work must only be performed by an authorised electrician.
WARNING
Damage to the device through incorrect assembly
Observe the protection class.
NOTICE
After connecting the control system, the threaded connections must be
tightened to the following torque:
[1] to 3,0 Nm
[2], [4], [5] to 1,5 Nm
[3] to 6,0 Nm
Housing cover to 2,5 Nm
5
1
24
3
1 Power supply
2 Temperature sensor
3 Light cables
4 Motor M2
5 Motor M1
NOTE
A multiple sealing insert 4 x 4 mm is optionally
available for the light cables [3].
Fig. 1: Casing with screw fastenings

Structure/description 15
PatioControl
EN
1. Connect the 24 V power supply to the + and - terminals.
Use the applicable cable gland.
T+T-
S
5
S
4
P
2. Connect the first actuator to the M1+ and M1- terminals.
M1M2
3. Connect an optional temperature sensor to the T+ and T- terminals.
NOTE
Install the temperature sensor outside and close to the slats.
T+T-
S
5
S
4
P
Option:
4. If necessary, connect a second actuator to the M2+ and M2- terminals.
M1M2

16
3.4 Building electrical connection
The operator must connect the included power supply to a suitable 230 V AC power supply.
WARNING
The housing of the power supply must be connected to the PE conductor of the
feed line at the customer.
3.5 Icons and explanation of terms
• INT-1: intermediate position 1
default value = approx. 33% open (may vary depending on customer)
• INT-2: intermediate position 2
default value = approx. 66% open (may vary depending on customer)
• Protected position
position for protection of the pergola in a storm (default value = 100% open)
• DIP switch
The active position is shown in white. In the example DIP-1 is switched to OFF and DIP-2 to ON.

[Teach-in hand-held transmitter] 17
PatioControl
EN
4 Teach-in hand-held transmitter
Controls of the hand-held transmitter
Example: Tempotel2, Multitel2
1
2 3
5
4
6
7
9
10
11
8
1 Display
2 Menu key left
3 Menu key right
4 Joystick
5 Display of operating mode
6 DOWN key
7 STOP key
8 Status indicator
9 DOWN key
10 Selector key
11 Teach-in key P
NOTE
The layout of the controls may be different on other hand-
held transmitters.
For information see:
• www.elero.de/de/produkte/steuerungen
• www.elero.com/en/products/control-systems

18
1 "S4" key: close pergola
2 "S5" key: open pergola
3 "S2" switch: select options
1 ... lock at < -5 °C
2 ... snow function
3 ... only one actuator (M1)
4 ... rain alarm direction of travel
4 "S3" key: reset limit positions (reset)
5 "S1" key: power supply
1 ...actuator radio receiver
2 ...light control radio receiver
6 Light module (optional)
7 "FORCE" regulator: adjustment of cut-out force
8 "SPEED" regulator: adjustment of travel speed
9 LED-1 green
10 LED-2 red
Overview of base module
S1
S2
FORCE
SPEED
T+T-
S3
S5 S4
13
12
ON
12
ON
4
3
12
4
3
5
6
7
8
10
9