Elite Screens Evanesce B Series User manual

Rev.060116-D 1 www.elitescreens.com
In-Ceiling Electric Motorized Front Projection Screen
Evanesce B Series
User’s Guide
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra
Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens.
Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this
unit are prohibited and will void your warranty. For more information, please contact our Technical
Support Department at [phone] Ext. 604.
•Please retain this user’s guide for future reference.
•To avoid damaging the unit, do not use with any unauthorized accessories not recommended by
the manufacturer.
•Handle the unit carefully during transportation to avoid any damages.
•To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
•The power outlet supplying power to the unit should be close to the unit and easily accessible.
•Do not install the unit on uneven, inclined surfaces;
•Do not install in damp places to avoid an electric shock or short circuit.
•Do not place any heavy objects over the power cord.
•Position the power cord properly to avoid creating a trip obstacle.
•To avoid an electrical shock or fire, due to a loose contact or short circuit, do not overload the
power cord.
•The internal & external parts of this unit are not end user serviceable. Do not attempt to
disassemble this unit by yourself. No one except authorized technicians can open and make
repairs to this unit.
•Make sure the power source that this unit is connected to has a continuous power flow.
•If there is need to use an extension cord, make sure the cord has an equal rating as the appliance
to avoid over heat.
•Do not handle the power plug when your hands are wet or your feet are in contact with water.
•Properly dispose of this equipment according to the environmental regulations in your area when
product is no longer of service.

Rev.060116-D 2 www.elitescreens.com
Do not use this unit under the following circumstances.
•Disconnect the power cord under the conditions of heavy rain, wind thunder or lightning.
•Avoid direct sun light, rain shower and moisture.
•Keep away from fire sources and high temperature to prevent this device from overheating.
•Cut off the power supply first before transportation or maintenance.
•To avoid possible injury and/or an electric shock, do not attempt to use this screen if there is
obvious damage or if there are any evident broken parts.
Installation Warning
The instructions provided in this user’s guide are for reference only. Please consult a
professional installation company for further installation and safety advice. The installer must
insure that proper mounting hardware is used to provide adequate strength suitable for the
installation. Elite Screens is not liable for any faulty installations. For limit adjustment instructions,
please contact our Technical Support Department at [phone] Ext. 604
The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black
drop in the roller. Please be aware of this as it will void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the warranty with the manufacturer.
Please contact Elite Screens Customer Service for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures.
✓Reorient or relocate the receiving antenna of the device which may be casing the
interference.
✓Increase the separation between the screen and the device’s receiver.
✓Connect the equipment into a different power outlet other than the device.
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign
particles such as dust, sawdust, and/or liquids.
NOTE
Regardless of the mounting method, the screen should be securely supported so that the vibration or
pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure
the fasteners that are used are of adequate strength and suitable for the installation location.

Rev.060116-D 3 www.elitescreens.com
Evanesce B Series| Controls and Accessories
A. IR Remote
B. RF Remote
C. Wall switch control box
D. 5-12 volt trigger cable
E. IR extended “eye” receiver
F. Wireless 5-12v (3.5 mm)
mono trigger cable
G. AAA batteries
H. Bubble leveler
Screen Operation
Electric Current: Depending upon region, your Elite Screen will operate on 100v, 110v, or 220v voltage.
1.After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the poweroutlet.
2. Once the screen has power, you’ll be able to control it using any of the 6 methods described below.
6 ways to control your Evanesce B
1. IR remote control (Item A, Fig 1): The Infrared functions by direct line
of sight contact with a beam range of 30 feet. Aim the IR remote at the
“eye” receiver once it has been connected to the control box’s RJ45 port.
2. IR “Eye” Receiver (Item E, Fig 2): The IR “Eye” Receiver plugs
directly into the control box’s RJ45 port to present a low profile line-of-
sight control option for your IR remote control even in a recessed ceiling
installation.
3. RF Remote Control (Item B): The radio waves eliminate the need for a
direct line of sight with a range of 100 feet.
4. 3-Way Wall Switch (Item C, Fig 3): The 3-way wall switch is a wall
mount switch with an up/stop/down button and plugs directly into the
control box’s RJ45 port.
Fig.3
UP
STOP
DOWN
Fig.1
IR/RF remote
IR “eye” receiver
Fig.2
3 Way Wall Switch
(does not have IR sensor)
Control box
Control box

Rev.060116-D 4 www.elitescreens.com
6. Wireless 5-12 volt trigger (Item F, Fig 5): The RF
remote control serves as a dual purpose, independently as a
handheld remote control, or in conjunction with the
Wireless 5-12 volt trigger cable. The radio frequency
technology can be programmed to send a wireless signal to
synchronize its drop/rise with the projector’s power cycle.
Here’s how to set up your Wireless 5-12 volt trigger | Synchronization Instructions
Step1: Connect one end of the 3.5 mm wireless 5-12 volt trigger cable to the RF remote.
Step 2: Connect the other 3.5 mm end of the wireless 5-12 volt trigger cable to your projector
Step 3: Make sure to unplug your screen from the power outlet
Step 4: Hold the UP button on your RF remote
Step 5: While holding the UP button, plug the screen back to the power outlet
Step 6: Wait 5 seconds and then release the UP button
Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and
able to control your screen with your projector’s power cycle
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-
30seconds for full off and on cycle each time)
Hardware Parts List for Evanesce B Series
Please make sure all parts listed below are included before proceeding with the installation.
Hardware Parts List for above ceiling installation
A. Suspension Bracket x 2
B. Suspension Bar x 4
C. End Flange x 2
C. M8x16mmx1.5mm washer x 8
D. M6x13mmx2mm washer x 8
E. M8 nut x 4
F. M6 nut x 4
G. M8x40mm hex screw x 4
H.M6x20mm screw x 4
DC 5-12V
out
The back ofthe
projector
Wireless 5-12V trigger cable
UP
Stop
Down
Fig 5
5. 5-12 volt trigger (Item D, Fig 4): The built-in 5-12V
trigger input allows your screen to synchronize its drop &
rise with the projector’s power cycle. The screen deploys
when the projector powers up and will retract when the
projector powers down. The 5-12 volt RJ45 cable connects
to your projector’s trigger output via a separate cable that
may or may not be provided by the manufacturer of the
projector. The trigger feature will not work without an
output cable from the projector, but it can be tested by
connecting the Red (+) and Green (-) cable to a 9-volt
battery.
RJ45 Input
5-12 volt trigger cable
Fig.4

Rev.060116-D 5 www.elitescreens.com
Installation Instructions
The Evanesce B allows access for above or below ceiling installation. Please follow the instructions
described in the following steps below for your type of installation.
Power
The Evanesce B Series includes a 3-Prong
Power Cord (2-Prong Power Cord for some
countries) for use in a non-concealed power
outlet. If your installation will be entirely
concealed (including power outlet), Elite
Screens strongly recommends a hardwire
connection. Please refer to the image below
for both 110v & 220v wiring information.
A. Above Ceiling Installation Instructions
Assembly
1. Place the hanging bracket (A) over the left and right side ends of the housing and secure each
one using the M8x40mmhex screw (G), M8x16mmx1.5mm washers (C) and M8 nut (E) as
shown below.
Hanging Bracket
(A)
G
C
E

Rev.060116-D 6 www.elitescreens.com
2. Place the Suspension Bar (B) over the Hanging Bracket (A) and align with the hole as shown
below according to the height requirement for your installation area. Secure the Suspension Bar
(B) with the M6x20mmScrew (B), M6x13mmx2mmWasher (E) and the M6 Nut (F). Repeat
the process for the other side.
3. Insert the end flange piece (C) on the edge of the housing as shown below to complete the assembly.
The screen is now ready for installation.
B. Below ceiling installation instructions
Please make sure all parts listed below are included before proceeding with the installation.
Hardware Parts List for below ceiling installation
A. End Flange x 2
B. Hanging bracket x 2
C. Threaded rod x 4
D. Socket wrench x 1
E. M8x16mmx1.5mm
washer x 28
F. M8 nut x 20
G.M8 Top expanding bolt x 4
H. M8x40mm hex screw x 4
H
D
F
Push end flange piece into
housing end until it snaps in
B
A

Rev.060116-D 7 www.elitescreens.com
D
H
G
1. Measure and cut the ceiling installation slot:
The width should not exceed 100mm and not less than the width of the screen’s housing. Measure the
length of your screen to determine the length.
2. Drill 4 holes in the ceiling that correspond with the attachments on the various casing sizes. The
width should be 120mm. The length of (A5) in the diagram below depicts the distance between the
holes located on each ear end of the screen’s case.
3. The M8expanding bolts (G) mount into thick wood beams, stone or concrete and will support the
screen. Use the Socket wrench (D) to attach the M8x40mm hexagonal screws. The expanding bolts
should be firmly tightened and tested to make sure that they will hold the weight of the screen.
The ceiling wall
Install screw holes
70
Ceiling
Ceiling Truss
Screen installation slot
100

Rev.060116-D 8 www.elitescreens.com
4. Insert the threaded rods(C) through the M8 expanding bolts and then attach the M8x40mm
hexagonal screws with the washer (E). Last put the Hanging Bracket (B) through the threaded rod
equal to the height of the screen’s housing. Once they are firmly in place (as shown below) make sure
that they will hold the weight of the screen.
5. Push the screen up into the space. Use the threaded rods (C) to attach the screen assembly to the
ceiling. The hexagonal screws (E) will connect the screen to the rest of the assembly. Once firmly in
place; use the nuts (F) to ensure a firm connection. Use the socket wrench (D) to make sure that the
bolts are firmly tightened.
6. Install end flange cover panel (A) between the gap and the screen to complete the installation.
For local Elite Screens contact or Technical Support, please visit
www.elitescreens.com
Ceiling
Socket wrench (H)
Ceiling
E and F
C
B
C
Push
Push the screen to
the hole of the
ceiling，the
screw across the
hole of the end
cap.
Use the Socket wrench
to attach the washer
and the outside
hexscrews, and then
adjust the bottom of
the screen to make it
parallel with the
ceiling, and then fasten
the screw.